Hearth and Home Technologies RCOR-HVB-IPI, LCOR-HVB-IPI owner manual Venting with Two 90 Elbows

Page 24

	NATURAL GAS		H1	V
	VENTING WITH TWO 90° ELBOWS			H
	V (FT.)	H + H1 (FT.)		H
	V (FT.)	H + H1 (FT.)
	900 Elbow on top	2.5’ MAX. (64mm)
	1' MIN. (305mm)	3' MAX. (914mm)
	2' MIN. (610mm)	6' MAX.	(1.83m)
	3' MIN. (914mm)	9' MAX.	(2.7m)
	4' MIN. (1.22m)	12' MAX.	(3.6m)
	5’ MIN. (1.5m)	15’ MAX.	(4.5m)
	6’ MIN. (1.83m)	18’ MAX.	(5.5m)
	V + H + H1 = 50’ MAX. (15.2m)
	H + H1 = 18’ MAX. (5.5m)
		PROPANE
	VENTING WITH TWO 90° ELBOWS
	V (FT.)	H + H1 (FT.)
	900 Elbow on top	2’ MAX. (610mm)
	1' MIN. (305mm)	2' MAX. (610mm)
	2' MIN. (610mm)	4' MAX.	(1.22m)
	3' MIN. (914mm)	6’ MAX. (1.83m)
	4' MIN. (1.22m)	8' MAX.	(2.4m)
	5’ MIN. (1.5m)	10' MAX.	(3.0m)
	6’ MIN. (1.83m)	12' MAX.	(3.6m)
	V + H + H1 = 50’ MAX. (15.2m)
	H + H1 = 12’ MAX. (3.6m)
	NATURAL GAS
	VENTING WITH TWO 90° ELBOWS
	V + V1 (FT.)	H (FT.)
	900 Elbow on top	2.5’ MAX. (64mm)
	1' MIN. (305mm)	3' MAX. (914mm)
	2' MIN. (610mm)	6' MAX.	(1.83m)	V1
	3' MIN. (914mm)	9' MAX.	(2.7m)	V1
	3' MIN. (914mm)	9' MAX.	(2.7m)
	4' MIN. (1.22m)	12' MAX.	(3.6m)
	5’ MIN. (1.5m)	15’ MAX.	(4.5m)
	6’ MIN. (1.83m)	18’ MAX.	(5.5m)	V
	V + V1 + H = 50’ MAX. (15.2m)			V
				H
		PROPANE
	VENTING WITH TWO 90° ELBOWS
	V + V1 (FT.)	H (FT.)
	900 Elbow on top	2’ MAX. (610mm)
	1' MIN. (305mm)	2' MAX. (610mm)
	2' MIN. (610mm)	4' MAX.	(1.22m)
	3' MIN. (914mm)	6’ MAX. (1.83m)
	4' MIN. (1.22m)	8' MAX.	(2.4m)
	5’ MIN. (1.5m)	10' MAX.	(3.0m)
	6’ MIN. (1.83m)	12' MAX.	(3.6m)
	V + V1 + H = 50’ MAX. (15.2m)
	Figure 15. Venting with Two 90° Elbows
				24

Image 24

Contents ST-HVB-IPI LCOR-HVB-IPI RCOR-HVB-IPI What to do if you smell gasSafety and Warning Information Table of Contents Pier-HVB-IPI NG, LP Exploded Parts Diagram / Vue éclatée des pièces PIER-HVB-IPIST-HVB-IPI ST-HVB-IPI LCOR-HVB-IPI LCOR-HVB-IPI RCOR-HVB-IPI RCOR-HVB-IPI PIER-HVB-IPI, ST-HVB-IPI L&RCOR-HVB-IPI Installation Codes High Altitude InstallationsAppliance Certification CertificationPre-install Preparation Introducing the Heat & Glo Gas FireplacesANY Such Action MAY Possibly Cause a Fire Hazard Diagram of the PIER-HVB-IPI Diagram of the ST-HVB-IPI Diagram of the LCOR-HVB-IPI and RCOR-HVB-IPI 121mmFireplace Dimensions and Locations Locating the FireplaceFraming the Fireplace Clearance RequirementsModel AT Each Joint Installing the Vent System Vent System Approvals Tems or Components MAY be Used Identifying Vent ComponentsStraight UP Vertical Venting MAX .2 MStraight OUT Max. Run 24 610 mmVenting with One 90 Elbow Venting with Two 90 Elbows Venting with Two 90 Elbows Venting with three 90 elbows Venting with three 90 elbows Installing Vent Components Attach the First Vent Component to the Starting CollarsInstall Support Brackets Continue Adding Vent ComponentsAttic Firestop Positioned SO That the Arrow is Pointing UPVent Termination Minimum Clearances Minimum Height from Roof to Lowest Discharge Opening Positioning, Leveling, and Securing the Fireplace Gas Control SystemSecuring of a Fireplace Fireplace Junction BOX in a IPI SystemGas Supply Line Gas Pressure RequirementsWiring the Fireplace For Intermittent Pilot Ignition Wiring Operation using Battery PowerAppliance Requirements Fan Wiring Diagram Optional Accessories Wall Switch Corner fan locationFinishing ANY MannerHearth Extensions Installing Trim, Logs & Ember Material Using a 5/16 nut driver remove the two bolts see Figure Placing the Ember MaterialAfter the Installation Double-check for faulty componentsBefore Lighting the Fireplace Lighting the FireplaceFireplace Maintenance Important Turn OFF the GAS Before Servicing Your Fireplace