Hearth and Home Technologies QVI-25FB-S owner manual Installation Preparation

Page 10

6 Installation Preparation

Prepare the existing solid fuel masonry or factory built non-combustible firebox for installation.

A. Flue Damper

Fully lock the solid fuel fireplace’s flue damper in the open position, OR completely remove it.

E. Fireplace Conversion Notice

Permanently attach the label with the following warning to the inside lower back of the fireplace firebox into which the insert is being installed. Silicone may be required to properly secure the label.

B. Chimney

•Ensure chimney is constructed of non-combustible materials.

•Ensure chimney is clean and in good working order.

•Ensure that all chimney cleanouts fit properly to prevent air leakage into chimney.

C. Gas Line

Note: If the factory built fireplace has no gas access hole provided, an access hole of 1 inch (25 mm) diameter or less may be drilled through the lower sides or bottom of the firebox in a proper workmanship - like manner. This access hole must be plugged with non-combustible insulation after the gas supply line has been installed.

•Install gas line into firebox cavity.

•Check local codes and gas line sizing requirements following NFPA54. See Section 8.

WARNING

Fire Risk.

This fireplace has been converted for use with a gas fireplace insert only and cannot be used for burning wood or solid fuels unless all original parts have been replaced, and the fireplace re- approved by the authority having jurisdiction.

Prior to installing the gas insert:

•Have the chimney and adjacent structure inspected and cleaned by qualified professionals. Hearth & Home Technologies recommends that NFI or CSIA certified professionals, or technicians under the direction of certi- fied professionals, conduct a minimum of a NFPA 211 Level 2 inspection of the chimney.

•Replace component parts of the chimney and fireplace as specified by the professionals.

•Ensure all joints are properly engaged and the chimney is properly secured.

D. Hearth or Hearth Extension

WARNING

Fire Risk.

A hearth or hearth extension (if present) must comply with either of the following:

•The solid fuel burning fireplace manufacturer’s specification.

• Local building codes required by authority having jurisdiction.

• NFPA 211

F. Remote Control

The receiver for the remotes must be installed BETWEEN the base pan of the insert and the firebox of the wood- burning fireplace (see photo below).

EXISTING SIDE

REFRACTORY

REMOTE

RECEIVER

UNIT

EXISTING BOTTOM OF

FIREPLACE

10

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. E • 9/08

Page 9 Page 11
Image 10
Page 9 Page 11
Contents What to do if you smell gas ModelHOT Surfaces Homeowner Reference Information XxxxxxxxTable of Contents Listing and Code Approvals Inspect Appliance and Components Design and Installation ConsiderationsGetting Started Tools and Supplies NeededFireplace Size Requirements Minimum Fireplace OpeningClearances Clearances to Mantels or other Combustibles above ApplianceTermination Locations Vent Termination Minimum ClearancesHorizontal Venting Vent Information and DiagramsVent Table Key Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Class a Wood Pipe Inlet AIR Vent Pipe Stainless Steel Placing, Securing and Leveling the Appliance Factory Built Wood Burning Installing Adaptor and Termination CapMasonry Damper Flashing Kit OptionalFuel Conversions Gas Connection Gas InformationGas Pressures High Altitude Installations Check for GAS LeaksElectrical Information Wiring the ApplianceON/OFF Switch Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Fan Wiring Diagram Finishing Mantel ProjectionsAccessories Appliance SetupClean the Appliance Ember PlacementLog Placement Log Set Assembly LOGS-2031Positioning the Logs Quadra-Fire QVI-25FB-S 2031-910 Rev. E 9/08 Removing Glass Assembly Glass AssemblyAir Shutter Setting Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Standing Pilot Ignition Lighting ApplianceWhat to do if YOU Smell GAS Check Pilot Flame Appearance Initial Break-in ProcedurePilot Adjustment After Appliance is LitFrequently Asked Questions Issue SolutionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Troubleshooting Symptom Possible Cause Corrective ActionMaintenance Tasks Maintaining and Servicing ApplianceInspect Maintenance Tasks Doors, SurroundsQVI-25FB-S Model Dimensions Appliance Dimension DiagramReference Materials Vent Kits Components Direct Vent Flex Liner Kits119 1312 Log Set AssemblyService Parts List Part number list on followingStocked Service PartsAt Depot Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

QVI-25FB-S specifications

Hearth and Home Technologies has carved a niche for itself in the realm of modern heating solutions, and the QVI-25FB-S fireplace is a testament to their commitment to innovation, efficiency, and aesthetic appeal. This model brings together cutting-edge technologies and design elements that elevate any living space, combining functionality with style.

The QVI-25FB-S is a direct vent gas fireplace insert, which means it can be installed into an existing fireplace or new construction. One of its standout features is its aesthetic versatility, available in multiple finishes and styles to fit seamlessly into various home decors. Its clean, contemporary lines and realistic flame presentation create an inviting ambiance, making it a perfect focal point in any room.

This model excels in energy efficiency, boasting an impressive efficiency rating. It utilizes advanced combustion technology that ensures minimal energy wastage while providing consistent heat output. The direct venting system is designed to draw air from outside, making it a great choice for energy-conscious homeowners looking to reduce their heating bills without sacrificing comfort.

One of the hallmark features of the QVI-25FB-S is its user-friendly interface. Equipped with a simplified remote control, this fireplace enables easy adjustment of flame height and heat output, catering to the user's comfort preferences. This allows for maximum convenience, whether you want to create a cozy atmosphere on a chilly night or provide moderate warmth during cooler seasons.

For safety and reliability, the QVI-25FB-S includes several important safety features. An automatic shut-off system ensures the unit will turn off if it detects any irregularities. Additionally, its glass front comes with a safety screen to prevent accidental contact with the hot surface, making it an ideal choice for homes with children or pets.

The QVI-25FB-S also supports eco-conscious lifestyles. By utilizing natural or propane gas, it produces lower emissions compared to traditional wood-burning fireplaces, making it a cleaner option for heating. The fireplace's innovative design minimizes pollutants while maximizing heat output, aligning perfectly with sustainable living practices.

In conclusion, the Hearth and Home Technologies QVI-25FB-S fireplace insert is a superior choice for those seeking an efficient, stylish, and user-friendly heating solution. With its advanced technology, safety features, and environmental considerations, it is well-suited for today’s modern home, delivering warmth and elegance year-round. Whether you are remodeling or building anew, this fireplace promises to be a stunning and practical addition to your living space.
Top Page Image Contents