Hearth and Home Technologies QVI-25FB-S owner manual Placing, Securing and Leveling the Appliance

Page 13

CUT AND BEND

FLASHING AS NEEDED

TO FIT CHIMNEY

SEALANT

ADHESIVE

Figure 7.2

•Trim chimney top plate to minimize excess overhang or bend over flue tile (see Figure 7.2).

•Place 3/8 inch bead of 300º F silicone on flue tile top.

C.Placing, Securing and Leveling the Appliance

•Install insert (without surround attached) into existing fireplace while pulling collar slide plate forward.

•Install gas line into hole provided on insert side.

•If applicable install remote control wires into insert side (see Section 6, F.).

•Secure collar slide plate to appliance by placing locking handle into position with locking tabs (see Figure 7.1) and secure with #8 screw.

•Level the appliance from side to side and front to back. If necessary, use the leveling legs included with the manual bag to set each corner of the base.

•Position any excess flexible vent pipe back up into chimney without sagging. Twist and push flex vent together to shorten.

•Install fiberglass insulation pieces to back face of surround.

•Attach surround. Follow instructions accompanying surround.

•Push insert so that surround becomes tight against face of fireplace.

WARNING

Fire Risk.

Only an approved Hearth & Home Technologies surround may be used to cover integral grills on solid fuel burning fireplaces.

• No other components such as shrouds, sheet- metal plates, etc., may be used to seal off vents.

WARNING

Failure to position the parts in accordance with these diagrams or failure to use only parts specifically approved with this appliance may result in property damage or personal injury.

WARNING

Explosion Risk.

Combustion Fume Risk.

•Connect vent sections per installation instructions.

•The 3 foot section of stainless steel flexible pipe MUST be attached directly to the exhaust collar on the collar slide plate.

•Connect exhaust vent pipe ONLY to exhaust starting collar and termination cap center collar.

•Connect inlet air vent ONLY to inlet air collar on appliance and either the termination cap inlet air collar OR terminate within chimney.

•Do NOT allow vent to sag below connection point to appliance.

Quadra-Fire • QVI-25FB-S • 2031-910 Rev. E • 9/08

13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents What to do if you smell gas ModelHOT Surfaces Xxxxxxxx Homeowner Reference InformationTable of Contents Listing and Code Approvals Getting Started Design and Installation ConsiderationsInspect Appliance and Components Tools and Supplies NeededMinimum Fireplace Opening Fireplace Size RequirementsClearances to Mantels or other Combustibles above Appliance ClearancesVent Termination Minimum Clearances Termination LocationsVent Table Key Vent Information and DiagramsHorizontal Venting Measuring StandardsInstallation Preparation Connecting Vent Pipe Installing Vent Pipe and ApplianceVenting Components Class a Wood Pipe Inlet AIR Vent Pipe Stainless Steel Placing, Securing and Leveling the Appliance Masonry Installing Adaptor and Termination CapFactory Built Wood Burning Damper Flashing Kit OptionalFuel Conversions Gas Connection Gas InformationGas Pressures Check for GAS Leaks High Altitude InstallationsON/OFF Switch Wiring the ApplianceElectrical Information Appliance RequirementsInstallation for Fan Optional Junction Box InstallationOptional Accessories Fan Wiring Diagram Mantel Projections FinishingClean the Appliance Appliance SetupAccessories Ember PlacementLog Placement Log Set Assembly LOGS-2031Positioning the Logs Quadra-Fire QVI-25FB-S 2031-910 Rev. E 9/08 Air Shutter Setting Glass AssemblyRemoving Glass Assembly Replacing Glass AssemblyBefore Lighting Appliance Operating InstructionsBefore operating this appliance have a qualified technician Standing Pilot Ignition Lighting ApplianceWhat to do if YOU Smell GAS Pilot Adjustment Initial Break-in ProcedureCheck Pilot Flame Appearance After Appliance is LitIssue Solutions Frequently Asked QuestionsSymptom Possible Causes Corrective Action TroubleshootingStanding Pilot Ignition System Symptom Possible Cause Corrective Action TroubleshootingMaintaining and Servicing Appliance Maintenance TasksDoors, Surrounds Inspect Maintenance TasksQVI-25FB-S Model Dimensions Appliance Dimension DiagramReference Materials Direct Vent Flex Liner Kits Vent Kits ComponentsService Parts List Log Set Assembly119 1312 Part number list on followingStocked Service PartsAt Depot Valve Assembly CONDITIONS, Exclusions & Limitation of Liability Limited Lifetime Warranty Contact Information

QVI-25FB-S specifications

Hearth and Home Technologies has carved a niche for itself in the realm of modern heating solutions, and the QVI-25FB-S fireplace is a testament to their commitment to innovation, efficiency, and aesthetic appeal. This model brings together cutting-edge technologies and design elements that elevate any living space, combining functionality with style.

The QVI-25FB-S is a direct vent gas fireplace insert, which means it can be installed into an existing fireplace or new construction. One of its standout features is its aesthetic versatility, available in multiple finishes and styles to fit seamlessly into various home decors. Its clean, contemporary lines and realistic flame presentation create an inviting ambiance, making it a perfect focal point in any room.

This model excels in energy efficiency, boasting an impressive efficiency rating. It utilizes advanced combustion technology that ensures minimal energy wastage while providing consistent heat output. The direct venting system is designed to draw air from outside, making it a great choice for energy-conscious homeowners looking to reduce their heating bills without sacrificing comfort.

One of the hallmark features of the QVI-25FB-S is its user-friendly interface. Equipped with a simplified remote control, this fireplace enables easy adjustment of flame height and heat output, catering to the user's comfort preferences. This allows for maximum convenience, whether you want to create a cozy atmosphere on a chilly night or provide moderate warmth during cooler seasons.

For safety and reliability, the QVI-25FB-S includes several important safety features. An automatic shut-off system ensures the unit will turn off if it detects any irregularities. Additionally, its glass front comes with a safety screen to prevent accidental contact with the hot surface, making it an ideal choice for homes with children or pets.

The QVI-25FB-S also supports eco-conscious lifestyles. By utilizing natural or propane gas, it produces lower emissions compared to traditional wood-burning fireplaces, making it a cleaner option for heating. The fireplace's innovative design minimizes pollutants while maximizing heat output, aligning perfectly with sustainable living practices.

In conclusion, the Hearth and Home Technologies QVI-25FB-S fireplace insert is a superior choice for those seeking an efficient, stylish, and user-friendly heating solution. With its advanced technology, safety features, and environmental considerations, it is well-suited for today’s modern home, delivering warmth and elegance year-round. Whether you are remodeling or building anew, this fireplace promises to be a stunning and practical addition to your living space.
Top Page Image Contents