Hearth and Home Technologies NorthStar-NT Electrical Access and Wiring Diagram, Suggestions

Page 13

Suggestions:

1.Insulate chase.

2.Finish chase walls with dry wall 5/8 in. (16mm) Type X face tape.

3.All dimensions are to finished walls and ceilings.

Figure 13.1 Sheetrocked Chase

WARNING

Fire Risk

Comply with all minimum clearances speci- fied.

•A minimum 1/2 in. (13mm) air clearance must be maintained at the back and 1 in. (25mm) to the sides of the fireplace assembly.

•Chimney sections at any level require a 2 in. (51mm) minimum air space clearance between the framing and chimney section.

WARNING

Fire Risk

Do not apply combustible finishing materials over any part of the front of this fireplace.

•The metal fireplace face may only be covered with noncombustible materials such as ceramic tile, brick, or stone.

•Do not cover or block any cooling air slots.

The decorative fascia must be removable for future serviceability of the Automatic Combustion Control.

WARNING

Fire Risk

•Maintain clearances.

•Use only non-combustible material below standoffs, material such as cement board is acceptable.

•Framing or finishing material used on the front of, or in front of, the appliance closer than the minimums listed, must be constructed entirely of noncombustible materials (i.e., steel studs, concrete board, etc.).

D. Electrical Access and Wiring Diagram

NOTE: The manual override switch, rheostat speed control and cover plate are supplied. You will need to supply: 14-3 wire with ground; 14-2 wire with ground; standard wall mount junction box; and wire nuts.

1.

Remove junction box cover plate on the

 

bottom right side of the fireplace.

2.

Thread the 14-3 with ground wire through

 

the opening with the strain relief on the cover

 

plate.

3.

Match colors to wire harness, (red to red,

 

14-3 w/ground

Match colors to wire

WHITE

harness (red to red,

 

white to white, etc) and

 

secure with a wire nut

 

Standard wall mount with Junction Box

14-2 w/ground

WIRE NUT

WHITE

GREEN

white to white, etc) and secure with wire

nuts.

NOTE: Wiring for fans must be done before framed enclosure is completed. If using a Heat Zone kit, it also must be installed before enclosure is complete.

Power to the Fireplace

 

Snap Disc

RED

bypass switch

 

 

BLACK

Figure 13.2 Fan Wiring Diagram

BLACK

Incoming Power

(110V)

September 1, 2008

Heat & Glo • NorthStar EPA Fireplace • 480-1081C

Page 13

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Hot glass will cause burns Installation and OperationFire Risk Serial No Model Name Test Lab Report No Manufactured Date 007Table of Contents Appliance Certification Listing and Code ApprovalsMobile Home Approved BTU & Efficiency Specifications Glass SpecificationsGetting Started Design and Installation ConsiderationsNegative Pressure Asphyxiation RiskSeptember 1 Heat & Glo NorthStar EPA Fireplace 480-1081C Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesModel #NorthStar Clearances to Combustible Materials ClearancesMinimum Clearances to Combustibles Frame the FireplaceOptional Framing Construction / Reduced Mantel Height Non-Combustible MaterialsSuggestions Electrical Access and Wiring DiagramMaterials Construct the ChaseInstall the Outside Air Kit Installation of FireplaceRisk of Smoke Spillage Fire Risk Asphyxiation RiskHandle Left Closed Handle Right OpenPosition the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Position the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Chimney Termination Requirements Chimney RequirementsExample Using Offsets/ReturnsAssemble the Chimney Sections Installing CAK4A and Flex PipeAssembling Chimney Sections for the SL- 300 Series Installing Flex Pipe Install the Ceiling FirestopsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Chimney Termination 2-10-3 Rule Complete the EnclosureChimney Termination Requirements See Figures 25.1 Slanted RoofsInstall the Chimney Air Kit required in Canada Install the Roof FlashingMark the Exit Point of the Roof Cut Out the Hole in the RoofConsult local codes for framing details SL-300 Series Ceiling/Roof ThimbleChase Top Install the Termination CapChase Top Framing ‑1/2 in mm below the chase top. See Figure Fan Replacement AccessoriesDoor and Door Gasket Baffle Removal and InstallationMinimum Clearance to Combustibles Heat Zone Kit20 ft 3 6m 10 ft 1 3m No cut needed Run Length Cut Pipe Ft 6-12m4 wall Timer Assembly Timer Assembly ReplacementRemove & Replace Timer Exploded View of Entire Assembly for Point of Reference only Hearth Extension FinishingCalculating Alternate Floor Protection Material Positioning the Protective Metal Hearth Strips Model # NorthStarFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Risk of Fire Non-Combustible Facing Material InstallationMantel Mantel SpecificationsOperating Instructions Symptoms of Over-FiringOver-Firing Your Appliance General InformationKeep open during use Outside AirFirescreen Clear Space Near the FireplaceGlass Doors Fan OperationWood Fuel Hardwood vs. Softwood Moisture contentSeasoning Starting a Fire Storing WoodFire Risk Incorrect Positions Correct Baffle & Blanket PlacementAutomatic Combustion Control ACC Burning ProcessBurn Rates Burning GuidelinesOpacity Burn Rate BTU / Hr Slide Air ControlChimney Fire Fire SafetyUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostic Question Possible Causes of Condition Solutions Diagnostics and Problem SolvingDon’t get enough/any heat. What can I do about it? General Maintenance Maintenance and Servicing the FireplaceClean Creosote Chimney CleaningGlass Cleaning Glass ReplacementDisposal of Ashes Fire Risk Injury RiskFirebrick Replacement Maintenance Task List Care and Cleaning of Plated SurfacesInspect Maintenance Tasks Date of Service Performed By Description of Service Service And Maintenance LogReference Materials Fireplace DimensionsNorthStar Chimney Components 15-3/4 NorthStar Fireplace Diagram Parts DiagramNorthStar FP Service Parts and AccessoriesDescription Comments Serial Number Date Stocked Depot Service Parts Alpabetical OrderAccessories CONDITIONS, Exclusions & Limitation of Liability Warranty Policy Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Woodburning Fireplace NorthStar EPA CertifiedContact Information Dealer Telephone

NorthStar-GT, NorthStar-BK, NorthStar-NT specifications

Hearth and Home Technologies has established itself as a leader in the production of innovative heating appliances, particularly with the launch of its NorthStar series: NorthStar-NT, NorthStar-BK, and NorthStar-GT. These models are designed to deliver superior performance, aesthetic appeal, and advanced technology, making them an excellent choice for modern homes.

The NorthStar-NT model is ideally suited for those seeking a reliable and efficient heating solution. It boasts a powerful, advanced heating technology that maximizes heat output while minimizing fuel consumption. The NorthStar-NT employs a unique combustion system that ensures a cleaner burn, resulting in fewer emissions and a lower environmental impact. The sleek design of the NorthStar-NT allows it to blend seamlessly into any room, making it not just a heating unit but also an attractive focal point.

On the other hand, the NorthStar-BK variant stands out for its versatility and aesthetic flexibility. It offers an array of customizable options, enabling homeowners to match the unit's appearance with their interior decor. The NorthStar-BK features a large viewing area, which enhances the visual appeal of the flames while providing efficient heat distribution. This model incorporates user-friendly controls that allow for easy temperature adjustments, ensuring that comfort is just a button away.

The NorthStar-GT model elevates the heating experience with its advanced smart technology features. Equipped with Wi-Fi connectivity, the NorthStar-GT allows users to control the appliance remotely via a smartphone app. This model also supports voice-activated commands, integrating seamlessly with smart home systems. The NorthStar-GT emphasizes energy efficiency, with programmable settings that enable users to optimize heating schedules to their lifestyle, ultimately contributing to energy savings.

All three NorthStar models feature durable construction and high-quality materials designed to withstand years of use. Their construction ensures not only longevity but also safety, with multiple safety features integrated into each model. Easy maintenance and cleaning options further enhance their user-friendly design.

In summary, the Hearth and Home Technologies NorthStar series including the NorthStar-NT, NorthStar-BK, and NorthStar-GT brings together cutting-edge technology, unparalleled efficiency, and stunning aesthetics. Each model caters to different needs, ensuring that homeowners can find the perfect heating solution that fits their style and requirements.
Top Page Image Contents