Hearth and Home Technologies NorthStar-GT, NorthStar-NT, NorthStar-BK Remove & Replace Timer

Page 36

7.Move slider control rod and linkage arm to the right and out of the way. Pull rod down and out towards you. Lay the control arm down. Figures 36.1 and 36.2.

8.The timer assembly is bolted under the face. Use a 7/16 socket wrench to remove the 2 bolts. Figure 36.3.

9.There is very little room to pull the timer assembly out the front of the fireplace. Place your hand through the access door in the floor of the fireplace. Let the timer assembly drop down and then rotate it up through the access door. Figures 36.3 and 36.4.

Linkage Arm

Slider Control Rod

Figure 36.1

Remove 2 bolts from timer assembly

Slider Control Rod

Linkage Arm

Figure 36.2

Figure 36.3

Timer Assembly with Gasket

Figure 36.4

REMOVE & REPLACE TIMER

1. Loosen set screw on timer, remove 2 screws and remove timer. See Figure 36.5.

2.Install new timer using same 2 screws. It is very impor- tant that the D cut side of the timer shaft is facing the opposite side of the linkage timer arm. Figure 36.6.

Remove 2 screws

Remove Timer

Loosen Set Screw

Figure 36.5

D cut side of timer shaft must face away from the Linkage Timer Arm

Figure 36.6

Page 36

Heat & Glo • NorthStar EPA Fireplace • 480-1081C

September 1, 2008

Page 35 Page 37
Image 36
Page 35 Page 37
Contents Installation and Operation Hot glass will cause burnsFire Risk 007 Serial No Model Name Test Lab Report No Manufactured DateTable of Contents Listing and Code Approvals Appliance CertificationMobile Home Approved Glass Specifications BTU & Efficiency SpecificationsDesign and Installation Considerations Getting StartedNegative Pressure Asphyxiation RiskSeptember 1 Heat & Glo NorthStar EPA Fireplace 480-1081C Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationModel #NorthStar Clearances Clearances to Combustible MaterialsFrame the Fireplace Minimum Clearances to CombustiblesOptional Framing Construction / Reduced Mantel Height Non-Combustible MaterialsElectrical Access and Wiring Diagram SuggestionsConstruct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitFire Risk Asphyxiation Risk Risk of Smoke SpillageHandle Left Closed Handle Right OpenSecure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Level the Fireplace Position the Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsAssembling Chimney Sections for the SL- 300 Series Install the Ceiling Firestops Installing Flex PipeInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Complete the Enclosure Chimney Termination 2-10-3 RuleChimney Termination Requirements See Figures 25.1 Slanted RoofsInstall the Roof Flashing Install the Chimney Air Kit required in CanadaMark the Exit Point of the Roof Cut Out the Hole in the RoofSL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsInstall the Termination Cap Chase TopChase Top Framing ‑1/2 in mm below the chase top. See Figure Accessories Fan ReplacementBaffle Removal and Installation Door and Door GasketHeat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe Ft 6-12m 20 ft 3 6m 10 ft 1 3m No cut needed4 wall Timer Assembly Replacement Timer AssemblyRemove & Replace Timer Exploded View of Entire Assembly for Point of Reference only Finishing Hearth ExtensionCalculating Alternate Floor Protection Material Model # NorthStar Positioning the Protective Metal Hearth StripsFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Non-Combustible Facing Material Installation Risk of FireMantel Specifications MantelSymptoms of Over-Firing Operating InstructionsOver-Firing Your Appliance General InformationOutside Air Keep open during useClear Space Near the Fireplace FirescreenGlass Doors Fan OperationMoisture content Wood Fuel Hardwood vs. SoftwoodSeasoning Storing Wood Starting a FireFire Risk Correct Baffle & Blanket Placement Incorrect PositionsBurning Process Automatic Combustion Control ACCBurning Guidelines Burn RatesOpacity Burn Rate BTU / Hr Slide Air ControlFire Safety Chimney FireTroubleshooting Understanding Vent ProblemsDraft Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Maintenance and Servicing the Fireplace General MaintenanceClean Creosote Chimney CleaningGlass Replacement Glass CleaningDisposal of Ashes Fire Risk Injury RiskFirebrick Replacement Care and Cleaning of Plated Surfaces Maintenance Task ListInspect Maintenance Tasks Service And Maintenance Log Date of Service Performed By Description of ServiceFireplace Dimensions Reference MaterialsNorthStar Chimney Components 15-3/4 Parts Diagram NorthStar Fireplace DiagramService Parts and Accessories NorthStar FPService Parts Alpabetical Order Description Comments Serial Number Date Stocked DepotAccessories Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d NorthStar EPA Certified Woodburning FireplaceContact Information Dealer Telephone

NorthStar-GT, NorthStar-BK, NorthStar-NT specifications

Hearth and Home Technologies has established itself as a leader in the production of innovative heating appliances, particularly with the launch of its NorthStar series: NorthStar-NT, NorthStar-BK, and NorthStar-GT. These models are designed to deliver superior performance, aesthetic appeal, and advanced technology, making them an excellent choice for modern homes.

The NorthStar-NT model is ideally suited for those seeking a reliable and efficient heating solution. It boasts a powerful, advanced heating technology that maximizes heat output while minimizing fuel consumption. The NorthStar-NT employs a unique combustion system that ensures a cleaner burn, resulting in fewer emissions and a lower environmental impact. The sleek design of the NorthStar-NT allows it to blend seamlessly into any room, making it not just a heating unit but also an attractive focal point.

On the other hand, the NorthStar-BK variant stands out for its versatility and aesthetic flexibility. It offers an array of customizable options, enabling homeowners to match the unit's appearance with their interior decor. The NorthStar-BK features a large viewing area, which enhances the visual appeal of the flames while providing efficient heat distribution. This model incorporates user-friendly controls that allow for easy temperature adjustments, ensuring that comfort is just a button away.

The NorthStar-GT model elevates the heating experience with its advanced smart technology features. Equipped with Wi-Fi connectivity, the NorthStar-GT allows users to control the appliance remotely via a smartphone app. This model also supports voice-activated commands, integrating seamlessly with smart home systems. The NorthStar-GT emphasizes energy efficiency, with programmable settings that enable users to optimize heating schedules to their lifestyle, ultimately contributing to energy savings.

All three NorthStar models feature durable construction and high-quality materials designed to withstand years of use. Their construction ensures not only longevity but also safety, with multiple safety features integrated into each model. Easy maintenance and cleaning options further enhance their user-friendly design.

In summary, the Hearth and Home Technologies NorthStar series including the NorthStar-NT, NorthStar-BK, and NorthStar-GT brings together cutting-edge technology, unparalleled efficiency, and stunning aesthetics. Each model caters to different needs, ensuring that homeowners can find the perfect heating solution that fits their style and requirements.
Top Page Image Contents