Hearth and Home Technologies NorthStar-NT, NorthStar-GT, NorthStar-BK owner manual Chimney Assembly

Page 19

5 Chimney Assembly

Chimney must extend beyond combustible roof structure

Maintain minimum height of chimney above roof

Install roof flashing according to minimum requirements

Offsets/returns may not exceed 30° from vertical

Termination Cap

Additional support for tall chimneys

Storm Collar

Maintain minimum

clearances to combustibles as specified

Support straps for offsets/ returns must be secured to adequate framing

Ceiling firestops are required where chimney passes through ceiling or floor

Figure 19.1 Typical Chimney System - Guidelines for Chimney System Installation

NOTE:

•Chimney performance may vary.

•Trees, buildings, roof lines and wind conditions affect performance.

•Chimney height may need adjustment if smoking or overdraft occurs.

September 1, 2008

Heat & Glo • NorthStar EPA Fireplace • 480-1081C

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Hot glass will cause burns Installation and OperationFire Risk Serial No Model Name Test Lab Report No Manufactured Date 007Table of Contents Appliance Certification Listing and Code ApprovalsMobile Home Approved BTU & Efficiency Specifications Glass SpecificationsAsphyxiation Risk Design and Installation ConsiderationsGetting Started Negative PressureSeptember 1 Heat & Glo NorthStar EPA Fireplace 480-1081C Typical Fireplace System Typical Fireplace SystemInspect Fireplace and Components Tools and Supplies NeededFire Risk Explosion Risk Selecting Fireplace Location Framing and ClearancesModel #NorthStar Clearances to Combustible Materials ClearancesNon-Combustible Materials Frame the FireplaceMinimum Clearances to Combustibles Optional Framing Construction / Reduced Mantel HeightSuggestions Electrical Access and Wiring DiagramMaterials Construct the ChaseInstall the Outside Air Kit Installation of FireplaceHandle Right Open Fire Risk Asphyxiation RiskRisk of Smoke Spillage Handle Left ClosedPosition the Fireplace Secure the FireplacePlace the Protective Metal Hearth Strips Position the Protective Metal Hearth Strips Level the FireplaceChimney Assembly Chimney Termination Requirements Chimney RequirementsExample Using Offsets/ReturnsAssemble the Chimney Sections Installing CAK4A and Flex PipeAssembling Chimney Sections for the SL- 300 Series Installing Flex Pipe Install the Ceiling FirestopsDouble-check the Chimney Assembly Install the Attic Insulation ShieldSecure the Chimney Slanted Roofs Complete the EnclosureChimney Termination 2-10-3 Rule Chimney Termination Requirements See Figures 25.1Cut Out the Hole in the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Mark the Exit Point of the RoofConsult local codes for framing details SL-300 Series Ceiling/Roof ThimbleChase Top Install the Termination CapChase Top Framing ‑1/2 in mm below the chase top. See Figure Fan Replacement AccessoriesDoor and Door Gasket Baffle Removal and InstallationMinimum Clearance to Combustibles Heat Zone Kit20 ft 3 6m 10 ft 1 3m No cut needed Run Length Cut Pipe Ft 6-12m4 wall Timer Assembly Timer Assembly ReplacementRemove & Replace Timer Exploded View of Entire Assembly for Point of Reference only Hearth Extension FinishingCalculating Alternate Floor Protection Material Positioning the Protective Metal Hearth Strips Model # NorthStarFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Risk of Fire Non-Combustible Facing Material InstallationMantel Mantel SpecificationsGeneral Information Symptoms of Over-FiringOperating Instructions Over-Firing Your ApplianceKeep open during use Outside AirFan Operation Clear Space Near the FireplaceFirescreen Glass DoorsWood Fuel Hardwood vs. Softwood Moisture contentSeasoning Starting a Fire Storing WoodFire Risk Incorrect Positions Correct Baffle & Blanket PlacementAutomatic Combustion Control ACC Burning ProcessBurn Rate BTU / Hr Slide Air Control Burning GuidelinesBurn Rates OpacityChimney Fire Fire SafetyUnderstanding Vent Problems TroubleshootingDraft Problems Factory-built Fireplaces Troubleshooting Diagnostic Question Possible Causes of Condition Solutions Diagnostics and Problem SolvingDon’t get enough/any heat. What can I do about it? Creosote Chimney Cleaning Maintenance and Servicing the FireplaceGeneral Maintenance CleanFire Risk Injury Risk Glass ReplacementGlass Cleaning Disposal of AshesFirebrick Replacement Maintenance Task List Care and Cleaning of Plated SurfacesInspect Maintenance Tasks Date of Service Performed By Description of Service Service And Maintenance LogReference Materials Fireplace DimensionsNorthStar Chimney Components 15-3/4 NorthStar Fireplace Diagram Parts DiagramNorthStar FP Service Parts and AccessoriesDescription Comments Serial Number Date Stocked Depot Service Parts Alpabetical OrderAccessories CONDITIONS, Exclusions & Limitation of Liability Warranty Policy Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Dealer Telephone NorthStar EPA CertifiedWoodburning Fireplace Contact Information

NorthStar-GT, NorthStar-BK, NorthStar-NT specifications

Hearth and Home Technologies has established itself as a leader in the production of innovative heating appliances, particularly with the launch of its NorthStar series: NorthStar-NT, NorthStar-BK, and NorthStar-GT. These models are designed to deliver superior performance, aesthetic appeal, and advanced technology, making them an excellent choice for modern homes.

The NorthStar-NT model is ideally suited for those seeking a reliable and efficient heating solution. It boasts a powerful, advanced heating technology that maximizes heat output while minimizing fuel consumption. The NorthStar-NT employs a unique combustion system that ensures a cleaner burn, resulting in fewer emissions and a lower environmental impact. The sleek design of the NorthStar-NT allows it to blend seamlessly into any room, making it not just a heating unit but also an attractive focal point.

On the other hand, the NorthStar-BK variant stands out for its versatility and aesthetic flexibility. It offers an array of customizable options, enabling homeowners to match the unit's appearance with their interior decor. The NorthStar-BK features a large viewing area, which enhances the visual appeal of the flames while providing efficient heat distribution. This model incorporates user-friendly controls that allow for easy temperature adjustments, ensuring that comfort is just a button away.

The NorthStar-GT model elevates the heating experience with its advanced smart technology features. Equipped with Wi-Fi connectivity, the NorthStar-GT allows users to control the appliance remotely via a smartphone app. This model also supports voice-activated commands, integrating seamlessly with smart home systems. The NorthStar-GT emphasizes energy efficiency, with programmable settings that enable users to optimize heating schedules to their lifestyle, ultimately contributing to energy savings.

All three NorthStar models feature durable construction and high-quality materials designed to withstand years of use. Their construction ensures not only longevity but also safety, with multiple safety features integrated into each model. Easy maintenance and cleaning options further enhance their user-friendly design.

In summary, the Hearth and Home Technologies NorthStar series including the NorthStar-NT, NorthStar-BK, and NorthStar-GT brings together cutting-edge technology, unparalleled efficiency, and stunning aesthetics. Each model caters to different needs, ensuring that homeowners can find the perfect heating solution that fits their style and requirements.
Top Page Image Contents