Hearth and Home Technologies NorthStar-GT Getting Started, Design and Installation Considerations

Page 6

2 Getting Started

A. Design and Installation Considerations

• Upper level air leaks: recessed lighting, attic hatch

 

opening, duct leaks.

CAUTION

Check building codes prior to installation.

•Installation MUST comply with local, regional, state and national codes and regulations.

•Consult insurance carrier, local building inspector, fire officials or authorities having jurisdiction about restrictions, installation inspection and permits.

When planning a fireplace installation, it is necessary to de- termine the following information before installing:

•Where the fireplace is to be installed. See Sections 3 and 4.

•The vent system configuration to be used. See Sections

5 and 6.

•Electrical wiring. See Section 3.

•Framing and finishing details. See Sections 3, 6 and 8.

•Whether optional accessories are desired. See Section 12.

Draft is the pressure difference needed to vent fireplaces successfully. Considerations for successful draft include:

•Preventing negative pressure

•Location of fireplace and chimney

WARNING

Asphyxiation Risk

Negative pressure can cause spillage of combustion fumes and soot. Fire needs to draft properly for safe operation.

B. Negative Pressure

Negative pressure results from the imbalance of air avail- able for the fireplace to operate properly. Causes for this imbalance include:

•Exhaust fans (kitchen, bath, etc.).

•Range hoods.

•Combustion air requirements for furnaces, water heaters and other combustion appliances.

•Clothes dryers.

•Location of return-air vents to furnace or air conditioning.

•Imbalances of the HVAC air handling system.

To minimize the effects of negative air pressure, the follow- ing must be considered:

•Install the outside air kit.

•Ensure adequate outdoor air is supplied for combustion appliances and exhaust equipment.

•Ensure furnace and air conditioning return vents are not located in the immediate vicinity of the fireplace.

•Avoid installing the fireplace near doors, walkways or small isolated spaces.

•Recessed lighting should be a “sealed can” design; attic hatches weather stripped or sealed; attic mounted duct work and air handler joints and seams taped or sealed.

Location of the fireplace and chimney will affect performance. As shown in Figure 7.1, on page 7, the chimney should:

•Be installed through the warm airspace enclosed by the building envelope. This helps to produce more draft, especially during lighting and die-down of the fire.

•Penetrate the highest part of the roof. This minimizes the effects of wind turbulence.

•Be located away from trees, adjacent structures, uneven roof lines and other obstructions.

Offsets can restrict draft so their use should be minimized. Consider the fireplace location relative to floor and ceiling and attic joists.

The NorthStar Fireplace requires a minimum flue draft of -0.10 inches of water column on High, and -0.04 inches of water column on Low, as measured with a draft meter. Most dealers have draft meters available to measure your flue draft if you suspect a problem.

If the fire is difficult to start, and smoke spills out of the door, or you find it hard to establish and maintain a moderately high burn rate, then the flue draft is too low and corrective measures must be taken.

NOTE: Cold air infiltration can cause frosting on glass.

Page

Heat & Glo • NorthStar EPA Fireplace • 480-1081C

September 1, 2008

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Installation and Operation Hot glass will cause burnsFire Risk 007 Serial No Model Name Test Lab Report No Manufactured DateTable of Contents Listing and Code Approvals Appliance CertificationMobile Home Approved Glass Specifications BTU & Efficiency SpecificationsNegative Pressure Design and Installation ConsiderationsGetting Started Asphyxiation RiskSeptember 1 Heat & Glo NorthStar EPA Fireplace 480-1081C Typical Fireplace System Typical Fireplace SystemTools and Supplies Needed Inspect Fireplace and ComponentsFire Risk Explosion Risk Framing and Clearances Selecting Fireplace LocationModel #NorthStar Clearances Clearances to Combustible MaterialsOptional Framing Construction / Reduced Mantel Height Frame the FireplaceMinimum Clearances to Combustibles Non-Combustible MaterialsElectrical Access and Wiring Diagram SuggestionsConstruct the Chase MaterialsInstallation of Fireplace Install the Outside Air KitHandle Left Closed Fire Risk Asphyxiation RiskRisk of Smoke Spillage Handle Right OpenSecure the Fireplace Position the FireplacePlace the Protective Metal Hearth Strips Level the Fireplace Position the Protective Metal Hearth StripsChimney Assembly Chimney Requirements Chimney Termination RequirementsUsing Offsets/Returns ExampleInstalling CAK4A and Flex Pipe Assemble the Chimney SectionsAssembling Chimney Sections for the SL- 300 Series Install the Ceiling Firestops Installing Flex PipeInstall the Attic Insulation Shield Double-check the Chimney AssemblySecure the Chimney Chimney Termination Requirements See Figures 25.1 Complete the EnclosureChimney Termination 2-10-3 Rule Slanted RoofsMark the Exit Point of the Roof Install the Roof FlashingInstall the Chimney Air Kit required in Canada Cut Out the Hole in the RoofSL-300 Series Ceiling/Roof Thimble Consult local codes for framing detailsInstall the Termination Cap Chase TopChase Top Framing ‑1/2 in mm below the chase top. See Figure Accessories Fan ReplacementBaffle Removal and Installation Door and Door GasketHeat Zone Kit Minimum Clearance to CombustiblesRun Length Cut Pipe Ft 6-12m 20 ft 3 6m 10 ft 1 3m No cut needed4 wall Timer Assembly Replacement Timer AssemblyRemove & Replace Timer Exploded View of Entire Assembly for Point of Reference only Finishing Hearth ExtensionCalculating Alternate Floor Protection Material Model # NorthStar Positioning the Protective Metal Hearth StripsFascia Outer Tile or Marble Combustible Can Flange Floor Position the Hearth Extension Finishing Material Non-Combustible Facing Material Installation Risk of FireMantel Specifications MantelOver-Firing Your Appliance Symptoms of Over-FiringOperating Instructions General InformationOutside Air Keep open during useGlass Doors Clear Space Near the FireplaceFirescreen Fan OperationMoisture content Wood Fuel Hardwood vs. SoftwoodSeasoning Storing Wood Starting a FireFire Risk Correct Baffle & Blanket Placement Incorrect PositionsBurning Process Automatic Combustion Control ACCOpacity Burning GuidelinesBurn Rates Burn Rate BTU / Hr Slide Air ControlFire Safety Chimney FireTroubleshooting Understanding Vent ProblemsDraft Problems Factory-built Fireplaces Troubleshooting Diagnostics and Problem Solving Diagnostic Question Possible Causes of Condition SolutionsDon’t get enough/any heat. What can I do about it? Clean Maintenance and Servicing the FireplaceGeneral Maintenance Creosote Chimney CleaningDisposal of Ashes Glass ReplacementGlass Cleaning Fire Risk Injury RiskFirebrick Replacement Care and Cleaning of Plated Surfaces Maintenance Task ListInspect Maintenance Tasks Service And Maintenance Log Date of Service Performed By Description of ServiceFireplace Dimensions Reference MaterialsNorthStar Chimney Components 15-3/4 Parts Diagram NorthStar Fireplace DiagramService Parts and Accessories NorthStar FPService Parts Alpabetical Order Description Comments Serial Number Date Stocked DepotAccessories Warranty Policy Hearth & Home Technologies Limited Warranty CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d Contact Information NorthStar EPA CertifiedWoodburning Fireplace Dealer Telephone

NorthStar-GT, NorthStar-BK, NorthStar-NT specifications

Hearth and Home Technologies has established itself as a leader in the production of innovative heating appliances, particularly with the launch of its NorthStar series: NorthStar-NT, NorthStar-BK, and NorthStar-GT. These models are designed to deliver superior performance, aesthetic appeal, and advanced technology, making them an excellent choice for modern homes.

The NorthStar-NT model is ideally suited for those seeking a reliable and efficient heating solution. It boasts a powerful, advanced heating technology that maximizes heat output while minimizing fuel consumption. The NorthStar-NT employs a unique combustion system that ensures a cleaner burn, resulting in fewer emissions and a lower environmental impact. The sleek design of the NorthStar-NT allows it to blend seamlessly into any room, making it not just a heating unit but also an attractive focal point.

On the other hand, the NorthStar-BK variant stands out for its versatility and aesthetic flexibility. It offers an array of customizable options, enabling homeowners to match the unit's appearance with their interior decor. The NorthStar-BK features a large viewing area, which enhances the visual appeal of the flames while providing efficient heat distribution. This model incorporates user-friendly controls that allow for easy temperature adjustments, ensuring that comfort is just a button away.

The NorthStar-GT model elevates the heating experience with its advanced smart technology features. Equipped with Wi-Fi connectivity, the NorthStar-GT allows users to control the appliance remotely via a smartphone app. This model also supports voice-activated commands, integrating seamlessly with smart home systems. The NorthStar-GT emphasizes energy efficiency, with programmable settings that enable users to optimize heating schedules to their lifestyle, ultimately contributing to energy savings.

All three NorthStar models feature durable construction and high-quality materials designed to withstand years of use. Their construction ensures not only longevity but also safety, with multiple safety features integrated into each model. Easy maintenance and cleaning options further enhance their user-friendly design.

In summary, the Hearth and Home Technologies NorthStar series including the NorthStar-NT, NorthStar-BK, and NorthStar-GT brings together cutting-edge technology, unparalleled efficiency, and stunning aesthetics. Each model caters to different needs, ensuring that homeowners can find the perfect heating solution that fits their style and requirements.
Top Page Image Contents