Hearth and Home Technologies Tucson (8700) owner manual Venting KIT KIT #97-65001

Page 25

HearthStone Quality Home Heating Products Inc

Tucson Model #8700

INSTALLATION INSTRUCTIONS

FOR THE STANDARD HORIZONTAL

TERMINATION MINIMUM

VENTING KIT (KIT #97-65001)

1.Install the 4” inner collar by first placing the 4” x 6” gasket ring onto the base of the collar. Install the collar and gasket to the stove using 8 of the screws provided.

2.Install the outer collar in similar fashion using the larger gasket ring and the remaining 8 screws.

3.Install the 45º elbow over the outer collar. Place the elbow so that the twist lock end is pointing up.

4.Install one of the 9” pipe sections into the elbow by fully inserting it and turning approximately ¼ turn clockwise, until the 2 sections are fully locked. Install the 90º elbow in similar fashion.

5.Move the stove and pipe assembly back until the 90º elbow is flush to the wall. The 9” vertical pipe should be parallel to the wall. Draw a circle around the pipe. Use the center of this circle as the center point of the 10” x 10” square wall pass through. (It should be approximately 40-1/4” above the floor) Cut and frame the wall pass through.

6.Place the interior wall thimble into the 10” x 10” wall pass through. Secure it with 4 screws (not provided). Install the exterior portion of the thimble in similar fashion, overlapping the 2 sections.

›Caution: For building with vinyl siding,

a vinyl siding standoff should be installed between the vent cap and the exterior wall.

›

7. Install the horizontal vent termination on the outside of the wall. Make sure both of the retaining straps extend through interior wall thimble. Before attaching the vent termination to the outside of the house, run a bead of non-hardening mastic around its’ outside edges, so as to make a seal between it and the wall. The arrow on the end cap should point up. Secure the cap to the wall with the appropriate screws.

8.Place the thimble cover onto the 90º elbow. Put the 9” pipe into the horizontal vent cap, (the vent pipe must extend into the horizontal vent cap a minimum of 1-1/4”). Move the stove and vent pipe into position, insert the 9” pipe into the 90º elbow and twist to lock it. Secure the straps from the horizontal vent termination to the interior pipe with 2 sheet metal screws, keeping screws close to wall thimble as possible. Bend or cut the excess strapping so that the thimble cover will fit properly. Screw the thimble cover to the wall.

25

Page 24 Page 26
Image 25
Page 24 Page 26
Contents QUE Faire SI Vous Sentez UNE Odeur DE GAZ What to do if YOU Smell GASTucson Model #8700 What When Information SheetIntroduction Safety Information Fire Hazard Service CautionMust be Vented to Outside HOT SurfacesElectrical Hazard Ceramic Fiber LOG Safety InformationDo not Light Pilot or Main Burners by Hand Mobile Home Installations Specifications Cleaning Routine Maintenance and CareOWNER’S Information Daily OperationPilot Flame Pattern FIREBOX, PILOT, & Burner TubesReplace the Front Door Gasket AS Needed Class CleaningItems Required for Installation INSTALLER’S InformationCodes Packing ListHearth REQUIREMENT/FLOOR Protection Unpacking and InspectionMinimum Venting-Mantle Clearance To Clearance to CombustiblesSnorkel-Wall Clearance To Combustibles Acceptable Direct-Vent Termination Cap locations Venting Connection Venting InformationRestriction Plate Adjustment to Restriction PlateRestriction Plate Position Acceptable DIRECT-VENT Termination CAP Locations Venting Components ConfigurationApproved Venting System Components Chimney Liner SystemComponents For a Typical Snorkel Installation Clearances from the pipe to combustibles 90 0 Elbow Approved Venting Configuration for Horizontal TerminationCo-Linear & Chimney as Air Inlet Approved Configuration for Fireplace InstallationVenting KIT KIT #97-65001 Thermostat Placement Remote ControlThermostat Wiring Electrical ConnectionsWiring Instructions Wiring Diagram TucsonGAS Connections GAS Supply ConnectionsGAS Supply Installation of the LOG SET LOG PlacementLog Set Removal of LOG SETLighting the Unit for the First Time BREAK-IN ProcedureSmoke and Fumes Warning BREAK-IN WarningPilot Light Warning Initial AdjustmentsPrepare for Lighting Variable Output ControlLighting Instructions To Turn OFF GAS to Appliance AIR Shutter AdjustmentsBurner Flame Appearance Pilot AdjustmentCleaning › Warning do not Clean the Unit When IT’S HOT Maintenance CareFirebox Pilot & Burner FlamesCleaning the Glass › Warning Parts ListsTroubleshooting Troubleshooting Troubleshooting Limited FIVE-YEAR Warranty Limited Lifetime WarrantyLimited THREE-YEAR Warranty Limited ONE-YEAR WarrantyExclusions Qualifying for Warranty CoverageRemedy Warranty Registration

Tucson (8700) specifications

Hearth and Home Technologies Tucson (8700) represents a significant advancement in the realm of home heating solutions. This gas fireplace model combines elegant design with cutting-edge technology, providing both aesthetic appeal and functional efficiency. The Tucson is designed to serve as a focal point in any living space while delivering warmth and comfort.

One of the main features of the Tucson (8700) is its sleek, modern design. Available in a variety of finishes, the fireplace fits seamlessly into a range of decor styles, from contemporary to traditional. Its large viewing area provides an unobstructed view of the flames, creating an inviting ambiance. The glass front is both stylish and functional, enhancing the overall appeal while maximizing heat output without compromising safety.

The Tucson is engineered with advanced technology that prioritizes efficiency and convenience. It utilizes a direct vent system, ensuring that the fireplace draws air from the outside and expels exhaust gases efficiently, improving indoor air quality. This feature allows for installations in a variety of locations within the home without the need for traditional chimney systems.

Another notable characteristic is its adjustable flame height and heat output. Homeowners can easily customize the warmth and ambiance to suit their preferences, providing versatile heating options for various occasions. The Tucson includes a remote control feature, allowing users to operate the fireplace without having to leave their comfortable seating area.

Safety is a key consideration in the design of the Tucson (8700). Equipped with an automatic shutoff feature, the fireplace will turn off if it detects any irregularities, ensuring peace of mind for users. The glass front remains cool to the touch, minimizing the risk of burns.

Additionally, the Tucson can be complemented with a variety of decorative options, including log sets and decorative media, allowing homeowners to create a personalized look that matches their style. This flexibility, along with its efficiency and stunning design, makes the Hearth and Home Technologies Tucson (8700) a standout choice for modern homes seeking both beauty and warmth.
Top Page Image Contents