Hearth and Home Technologies 4100I-GD-B Blower Cord Location & Blower Control BOX with Switch

Page 15

R

4100-I ACT WOOD INSERT

BLOWER CORD LOCATION & BLOWER

CONTROL BOX WITH SWITCH

This insert comes standard with a blower, installed at the factory with blower cord on right side of insert (as you face the unit). The blower cord can also be installed on the left side. Disconnect the cord from right side. ROUTE WIRES IN FRONT OF FAN. Re-install on the left side. Do not route cord behind the cooling fan.

FAN (BLOWER) REPLACEMENT

Included in Kit: Replacement Blower

Tools Needed: 5-32 Wrench and Phillips Head Screwdriver.

1.Remove bolts from both sides of the insert and slide the lower cast cover towards you. See Figure 15D

2.Loosen 4 screws (2 on each side of the motor) that secures motor to the housing. Remove the motor. See

Figure 15E.

3.Attach new motor using the same screws to the blower housing.

4.Re-attach lower cast cover to insert using the bolts removed in Step 1.

Figure 15A

Black

Red

Snap Disc

White

 

Black

Blower Control

 

Box with Switch

Cooling Fan

Figure 15B - Right Side Location

Remove Bolt

Remove Bolt

Figure 15D

Black

Red

Snap Disc

White

 

Cooling Fan

Figure 15E

Remove 4 screws, lift motor from housing

Figure 15C - Left Side Location

Operating the Blower Control Box with Switch

1.The blower will turn on/off automatically when set to AUTO.

2.When set to MANUAL, the fan will turn on/off only when you turn it on or off. This setting over-rides the internal snap disc.

3.Adjust the speed of the fan by turning the HIGH/LOW knob to the desired setting.

AUTO: Fan will

MANUAL

 

turn ON/OFF

FAN

automatically and

AUTO

is controlled by the

 

 

internal Snap Disc

 

LOW

 

 

 

HIGH

OFF

 

 

MANUAL: Over-rides the internal Snap Disc

September 1, 2008

250-7201E

Page 15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Hot glass will cause burns Advanced Combustion Technology ACTLocation Back side of left side panel Serial Number007 Model NameTable of Contents Panel Size TOP ViewSide View Front ViewSee Alternative Floor Protection Worksheet on SideWallChimney HEIGHT/DRAFT Installation recommendationsRule A. These are safety requirements and are ListingsConverting R to k Thermal Conductivity k valueThermal Resistance R value Converting k to RInsulation Chimney RequirementsOvalizing Round Stainless Steel Liners FirestoppingUSA only Installing Outside AirInstallation Into Masonry Fireplace Installation OptionsFactory-built zero clearance fireplace Installation Into a Factory Built Zero Clearance FireplaceSheet Metal Guides Installation in CanadaAdjusting the Leveling Bolts Leveling Bolts and sheet metal shimsZero Clearance Fireplace Outside AIR Must be Turned to on Outside AIR InstallationRe-install plate Securing Liner to Chimney RingCompleted View Panel SET and Cast Trim SETPanel and Cast Trim must be ordered separately Panel and Gold Trim SETBlower Cord Location & Blower Control BOX with Switch Zero Clearance Adjustable Trim Support Door Handle AssemblyDoor Latch Adjustment Operation BTU / Hr Start-Up Air Control Primary Control Operating TipsBurn Rates OpacityBurning Process Replace with 5mm ceramic glass only MaintenanceBaffle Removal & Installation Brick replacement instructionsExploded Views Ceramic BlanketDescription Service Parts and Accessories Part Description Alphabetical Order Date of Service Performed By Description of Service CONDITIONS, Exclusions & Limitation of Liability Hearth & Home Technologies Limited WarrantyHearth & Home Technologies Limited Warranty Cont’d Telephone Where PurchasedSerial Number Date Purchased Date Installed ACT Wood Insert
Top Page Image Contents