Wayne 330002-001, SEL50, SEL40 specifications General Safety, Typical Installation

Operating Instructions and Parts Manual

General Safety Information				6. Check hoses for weak and worn		11. This equipment is only for use on
(Continued)				condition before each use, making		120 volt (single-phase) and is
General Safety				certain that all connections are		equipped with an approved­ 3-con­
				secure.		ductor­ cord and 3-prong, grounding-
1.	Know the pump application,			7. Periodically inspect the pump and		type plug as shown in Figure­ 1.
	limitations, and poten­tial­ hazards.
				system compo­nents­. Perform routine
		Do not		maintenance as required (See		Grounding
		use to		Maintenance Section).
pump flammable or				8. Provide a means of pressure relief for		blade
explosive fluids such
				pumps whose discharge line can be
as gasoline, fuel oil,
				shut-off or obstructed.
kerosene, etc. Do not						Figure 1
use in a flammable and/or explosive				9. Personal Safety:
atmosphere. Personal injury and/or				a. Wear safety glasses at all times
						To reduce the risk of electric shock, the
property damage could result.
				when working with pumps.
						motor must be securely and adequately
2. Make certain that the power source
				b. Keep work area clean, uncluttered
						grounded. This can be accom­plished­ by
	(electric motor) conforms to the			and properly lighted; replace all		the following:
	requirements of the equipment.			unused tools and equipment.		1. Inserting plug directly into a
				c. Keep visitors a safe distance from
						properly installed and grounded
				the work area. Make workshop		3-prong, grounding-type receptacle­
Disconnect power before
				child-proof with padlocks,­ master		(as shown in Figure 1).
servicing. If the power dis­				switches,­ and by remov­ing­ starter		2. Permanently wiring the unit with a
connect­ is out of sight, lock
				keys.
in the open posi­tion­ and tag						grounded, metal raceway system.
				10. When wiring an electri­cal­ly­ driven
it to prevent unexpected application of						3. Other suitable means.
power. Failure to do so could result in				pump such as this, follow­ all electrical		Where a 2-prong wall receptacle is
fatal electrical shock!				and safety codes, as well as the most
						encountered, it must be replaced with a
3.	Release all pressure within the			recent National Electrical Code (NEC)
						properly grounded 3-prong recep­ta­cle­
				and the Occu­pa­tion­al­ Safety and
	system before servic­ing­ any
						installed in accordance with the NEC
				Health Act (OSHA).
	component.
						and local codes and ordinances.
					Risk of
4. Drain all liquids from the system						12. All wiring should be performed by a
					electric
	before servicing.
						qualified electri­cian­.
				shock! Never connect the
5. Secure the discharge line before
				green (or green and yellow)		13. It is strongly recommended that this
	starting the pump. An unsecured
				wire to a live terminal!		unit is plugged into a Ground Fault
	discharge line will whip, possibly
						Circuit Interrupter (GFCI). Consult­ a
	causing personal injury and/or
						local electrician for installation and
	property damage.
						availability.
Three prong grounded outlet equipped with a ground fault interruptor
	2 inch Discharge pipe		Upper level drainage

		Cleanout		Vent pipe	Vent pipe	Shower
*					Lavatory
	2 inch
				Laundry tubs
	Gate Valve				Toilet
	45º Elbow
		Dryer	Washer
	2 inch
	Check
	Valve
Float	Flange	Floor drain		Washer drain
switch				* Main waste line to sewer or septic tank
	Sewage pump passes 2 inch dia. solids

Figure 2 - Typical Installation

www.waynepumps.com

2