AMX ENV-VST-C manual Disconnecting Power to All Hvac Equipment, Selecting the Thermostat Location

Page 9

Installation and Wiring

Installation and Wiring

Overview

This section covers the installation and wiring of a ViewStat Color Communicating Thermostat system.

120 volts may cause serious injury from electrical shock. Disconnect electrical power to the HVAC system before starting installation. This system is a low-voltage system.

Improper installation may cause serious injury from electrical shock. This system must be installed by a qualified contractor in accordance with NEC Standards and applicable local and state codes.

If you are using more than one thermostat on a single power transformer, use the maximum total current draw of all of the thermostats on the transformer times the voltage for the total "VA draw" of the thermostats on that individual transformer; then keep that value under 50% of the VA rating of the transformer.

Disconnecting Power to All HVAC Equipment

Since the thermostats wire directly to the HVAC equipment, you must shut off the power at the equipment. You can generally accomplish this by turning off the disconnect switch located near the equipment. If an obvious disconnect switch is unavailable, you need to remove the circuit breaker or shut down the fuse serving the equipment.

Failure to disconnect power could result in damage to the HVAC equipment or thermostats. Leave the power disconnected until you have made all other electrical connections and checked them for accuracy.

Selecting the Thermostat Location

Determine if the thermostat will be operating alone, or with remote temperature sensors. If the unit is stand-alone there are certain measures that must be taken to ensure accurate temperature control.

Stand-Alone Thermostat Mounting Criteria

Mount on an interior wall. In a room frequently occupied.

At least 18 inches (45.72 cm) from any outside wall.

Approximately 5 feet (1.52 m) above the floor. Check with local building codes for height requirements in commercial applications.

DO NOT locate the thermostat:

Behind doors, in corners or other dead air spaces.

In direct sunlight or near lamps, appliances or other sources of radiant heat. On an outside wall or wall exposed to an unconditioned space (i.e. garage, etc.). In the flow path of a supply register, in stairways or near outside doors.

On a wall where concealed pipes and/or duct work will affect the thermostat. Near sources of electrical interference such as arcing relay contacts.

Remote Temperature Sensors

When choosing an installation location for the remote sensor, follow the guidelines for placement of the thermostat, and locate the sensor where its operating range (see the ViewStat Color Thermostat Specifications table on page 1) will not be violated (i.e. do not install in a cold garage or hot equipment room).

See the Installing a Remote Sensor section on page 14 for details.

ENV-VST-C - Operation / Reference Guide

3

 

 

Image 9
Contents ENV-VST-C AMX Limited Warranty and Disclaimer Table of Contents Advanced Thermostat Operations Programming AxLink Channels AxLink Levels Weather Duet Module ViewStat Color Thermostat Specifications OverviewSystem Components Communication and Hvac ENV-VST-TSO Outdoor Temperature Sensor SpecificationsRemote Temperature Sensors Disconnecting Power to All Hvac EquipmentSelecting the Thermostat Location Stand-Alone Thermostat Mounting CriteriaWiring the Thermostat Removing the Faceplate from the BaseMounting the Base to a Wall Wiring Terminals Communication and Equipment Terminal Wiring DefinitionsCommunication and Equipment Terminal Wiring Definitions Preparing Captive Wires Wiring GuidelinesWiring for AxLink Single Stage Furnace and Single Stage A/C Wiring DiagramsDual Stage Furnace and Dual Stage A/C Dual Stage Furnace and Dual Stage A/C wiringRoof Top Unit with Dual Stage Heat and Dual Stage Cool Boiler and A/C with Separate Transformers Boiler and A/C with Separate Transformers wiringSingle Stage Heat Pump Single Stage Heat Pump wiringTwo Stage Heat Pump Two Stage Heat Pump wiringInstallation and Wiring Installing the Outdoor Temperature Sensor Installing a Remote SensorIndoor Flush Mount Temperature Sensor Specifications Installing the Indoor Flush Mount SensorSensor wire connected to cable Navigating the ViewStat Color Communicating Thermostat Front Panel ComponentsMain Screen Status Icons Changing the Heating and Cooling SetpointsChanging the Heating/Cooling Mode Changing Hold ModeHold Mode Options To ProgramHeating/Cooling Mode Options Changing the Fan ModeTurning Off the Hvac System Stops blinkingHelp Screen Fan Mode OptionsFan Auto Or coolingDay Forecast Screen Current Weather ScreenThermostat Mode Screen Thermostat Mode Screen OptionsExit Returns to the Main screen Establishing Daytime/Nighttime Temperature Settings Program ScreenProgram Screen Options Copy To screen Copying Programmed SettingsAway Mode Screen Establishing Away Mode SettingsAway Mode Screen Options Settings Screen Changing the Fan SettingsSettings Screen Options Changing the Filter Settings Accessing Advanced Setup Options Changing User PreferencesSecurity Code Screen Change Security Code Screen Entering the Security CodeChanging the Security Code User Preferences Screen Options User Preferences ScreenChanging the Date and Time Format Changing the Temperature ScaleDisabling the Filter Change Reminder Changing the Backlight SettingsDisabling the Weather Alert Icon Disabling the Forecast ScreensDisabling the Screen Saver Button Lockout Screen Options Button Lockout ScreenLocking the Buttons Locking the Temperature SettingsLocking the Mode Settings Locking the Fan SettingsAdvanced Setup Screen Options Advanced Setup ScreenChanging the Type of Hvac System When Diagnostic Mode is activeActivating the External Sensor Changing the Type of Fossil FuelSetting the Date and Time on the Thermostat Activating the Internal On-board SensorActivating the On-board Humidity Sensor Advanced Setup screen 2 Turning on Diagnostic ModeTurning on the Humidification and Dehumidification Systems Turning on Comfort RecoveryAxLink Communications screen AxLink Communications ScreenSwitching AxLink Devices Thermostat Setup Thermostat Setup ScreenThermostat Setup Screen Options Setting the Deadband Temperature Difference Setting First and Second Stage DifferentialsSetting the Balance Point for a Heat Pump System Setting the Temperature OffsetThermostat Setup screen 2 SENDCOMMANDs SENDCOMMANDsDay Forecast Commands Color ViewStat Thermostat CommandsDay Forecast Commands Weather Condition KeywordsAxLink Commands AxLink CommandsDisplays the current forecast Temperature scaleDew Point 55F To Off, the response reports OFFSendcommand ’LK MR1 TR3’ Sets the mode to Program Request the thermostat’s serial number Sets the current barometric pressureMaster requesting the thermostat’s serial number Thermostat returns the serial numberAxLink Channels AxLink ChannelsHvac State Emergency 219Heat 224 2nd stage heat relay Provides feedback from relay W2 246AxLink Levels Weather Duet ModuleAxLink Levels InConcert window Weather Setup PagesWeather Main Changing the Date and TimeChanging the Humidity Mode Changing the Humidity SettingsHumidity menu Changing the Heat and Cool SettingsHvac Mode menu Changing the Hvac ModeEntering Location by Zip Code Changing the Hold ModeEntering Location by Station ID Changing Temperature UnitsChanging Wind Speed Units Changing Pressure UnitsDay Forecast screen Programming ENV-VST-C Operation / Reference Guide Increase Your Revenue through education + knowledge
Related manuals
Manual 2 pages 4.04 Kb

ENV-VST-C specifications

The AMX ENV-VST-C is an advanced video streaming and encoding solution designed to meet the needs of modern broadcasting and professional video applications. Known for its high-performance capabilities and seamless integration into existing systems, the ENV-VST-C stands as a reliable choice for content creators, broadcasters, and businesses alike.

One of the main features of the AMX ENV-VST-C is its ability to support a wide range of video formats and resolutions. The device is capable of encoding and streaming in 4K, Full HD, and SD resolutions, ensuring that users can produce high-quality content regardless of their specific requirements. This versatility makes it suitable for various applications, including live event streaming, corporate communications, and even online educational platforms.

The ENV-VST-C utilizes state-of-the-art encoding technologies, such as H.264 and H.265, providing users with high-quality video while optimizing bandwidth usage. H.265, in particular, allows for significantly smaller file sizes compared to H.264, all without sacrificing video quality. This efficiency is crucial for users looking to reduce costs associated with bandwidth and storage, especially in environments where video distribution is critical.

Another key characteristic of this encoder is its user-friendly interface. The AMX ENV-VST-C features an intuitive control panel and web interface that allows users to configure settings, monitor performance, and manage live streams effortlessly. This ease of use is essential for operators who may not have in-depth technical knowledge but need to manage complex streaming tasks efficiently.

In addition, the AMX ENV-VST-C supports multiple streaming protocols, including RTMP, RTSP, and MPEG-TS. This capability enables seamless integration with various content delivery networks (CDNs) and ensures that users can reach their audience effectively across different platforms.

Moreover, the device is designed with reliability in mind. It offers features such as redundant power supplies and advanced cooling systems, which help maintain optimal performance even in demanding environments. This reliability is crucial for live streaming applications, where any downtime can result in significant loss of engagement and revenue.

In conclusion, the AMX ENV-VST-C stands out with its robust feature set, cutting-edge technologies, and user-centric design. Whether you are in broadcasting, corporate communication, or education, this encoder provides the performance and flexibility needed to deliver exceptional video content. With its commitment to quality and efficiency, the AMX ENV-VST-C is a valuable asset for anyone looking to enhance their video production capabilities.