AMX ENV-VST-C manual Color ViewStat Thermostat Commands, Day Forecast Commands

Page 58

Programming

SEND_COMMANDs (Cont.)

WAKE

Activates the display. Sets the display to active brightness.

 

Syntax:

 

SEND_COMMAND ’WAKE’

ZAP!

Restores the unit to its factory defaults, but does not change its AxLink address.

 

Syntax:

 

SEND_COMMAND ’ZAP!’

The Color ViewStat thermostat does not support string messages. A command message either does not have a response, or another command responds to it, but it never receives a string response.

Color ViewStat Thermostat Commands

This section lists commands that are specific to the Color ViewStat Thermostat.

5-Day Forecast Commands

The 5-Day Forecast commands, FH, FL, and FK, give the 5-Day Forecast sent in three separate messages, one for each of the following:

Expected high temperatures, FH Expected low temperatures, FL Expected weather conditions keywords, FK

The data always starts with the current day's information. Temperatures are be reported in the same scale as set on the thermostat, in Fahrenheit or Celsius. The Weather Condition Keywords have been shortened to accommodate for the AxLink 64 character message limit. The Weather Condition Keywords include the following:

Weather Condition Keywords

•

BLZ for Blizzard

•

HAZE

•

SMOKE

 

 

 

 

 

• BLSN for Blowing Snow

•

HUMID

•

SNOW

 

 

 

 

 

•

CLEAR

•

ICE

• SNOWFL for Snow Flurries

 

 

 

 

 

•

CLDY for Cloudy

•

MCLDY for Mostly Cloudy

• SNOWSW for Snow Showers

 

 

 

 

 

 

•

DRZL for Drizzle

•

MSUN for Mostly Sunny

•

SUN for Sunny

 

 

 

 

 

•

DUST

•

PCLDY for Partly Cloudy

• TSTORM for Thunder Storms

 

 

 

 

 

 

•

FAIR

•

RAIN

•

UNK for Unknown

 

 

 

 

 

•

FOG

•

RAINSW for Rain Showers

• VCOLD for Very Cold

 

 

 

 

 

• FZDRZL for Freezing Drizzle

•

RAINSN for Rain Snow Mix

•

WINDY

 

 

 

 

 

• FZRAIN for Freezing Rain

•

SLEET

 

 

 

 

 

 

 

 

5-Day Forecast Commands

FH

Forecasted 5-day high temperatures

Syntax:

FH <HT1> <HT2> <HT3> <HT4> <HT5>

Variable:

HTx = The high temperature in degrees expected for day x, where x = 1 is the current day, 2 is the next day, etc. Example:

SEND_COMMAND ’FH 78 82 85 84 85’

Five-day high temperatures.

52

ENV-VST-C - Operation / Reference Guide

Page 57 Page 59
Image 58
Page 57 Page 59
Contents ENV-VST-C AMX Limited Warranty and Disclaimer Table of Contents Advanced Thermostat Operations Programming AxLink Channels AxLink Levels Weather Duet Module Overview ViewStat Color Thermostat SpecificationsSystem Components ENV-VST-TSO Outdoor Temperature Sensor Specifications Communication and HvacSelecting the Thermostat Location Disconnecting Power to All Hvac EquipmentRemote Temperature Sensors Stand-Alone Thermostat Mounting CriteriaRemoving the Faceplate from the Base Wiring the ThermostatMounting the Base to a Wall Communication and Equipment Terminal Wiring Definitions Wiring TerminalsCommunication and Equipment Terminal Wiring Definitions Wiring Guidelines Preparing Captive WiresWiring for AxLink Wiring Diagrams Single Stage Furnace and Single Stage A/CDual Stage Furnace and Dual Stage A/C wiring Dual Stage Furnace and Dual Stage A/CRoof Top Unit with Dual Stage Heat and Dual Stage Cool Boiler and A/C with Separate Transformers wiring Boiler and A/C with Separate TransformersSingle Stage Heat Pump wiring Single Stage Heat PumpTwo Stage Heat Pump wiring Two Stage Heat PumpInstallation and Wiring Installing a Remote Sensor Installing the Outdoor Temperature SensorInstalling the Indoor Flush Mount Sensor Indoor Flush Mount Temperature Sensor SpecificationsSensor wire connected to cable Front Panel Components Navigating the ViewStat Color Communicating ThermostatChanging the Heating and Cooling Setpoints Main Screen Status IconsHold Mode Options Changing Hold ModeChanging the Heating/Cooling Mode To ProgramTurning Off the Hvac System Changing the Fan ModeHeating/Cooling Mode Options Stops blinkingFan Auto Fan Mode OptionsHelp Screen Or coolingCurrent Weather Screen Day Forecast ScreenThermostat Mode Screen Options Thermostat Mode ScreenExit Returns to the Main screen Program Screen Establishing Daytime/Nighttime Temperature SettingsProgram Screen Options Copying Programmed Settings Copy To screenEstablishing Away Mode Settings Away Mode ScreenAway Mode Screen Options Changing the Fan Settings Settings ScreenSettings Screen Options Changing the Filter Settings Changing User Preferences Accessing Advanced Setup OptionsSecurity Code Screen Entering the Security Code Change Security Code ScreenChanging the Security Code User Preferences Screen User Preferences Screen OptionsChanging the Temperature Scale Changing the Date and Time FormatChanging the Backlight Settings Disabling the Filter Change ReminderDisabling the Forecast Screens Disabling the Weather Alert IconDisabling the Screen Saver Button Lockout Screen Button Lockout Screen OptionsLocking the Temperature Settings Locking the ButtonsLocking the Fan Settings Locking the Mode SettingsAdvanced Setup Screen Advanced Setup Screen OptionsWhen Diagnostic Mode is active Changing the Type of Hvac SystemChanging the Type of Fossil Fuel Activating the External SensorActivating the Internal On-board Sensor Setting the Date and Time on the ThermostatActivating the On-board Humidity Sensor Turning on Diagnostic Mode Advanced Setup screen 2Turning on Comfort Recovery Turning on the Humidification and Dehumidification SystemsAxLink Communications Screen AxLink Communications screenSwitching AxLink Devices Thermostat Setup Screen Thermostat SetupThermostat Setup Screen Options Setting First and Second Stage Differentials Setting the Deadband Temperature DifferenceSetting the Temperature Offset Setting the Balance Point for a Heat Pump SystemThermostat Setup screen 2 SENDCOMMANDs SENDCOMMANDsDay Forecast Commands Color ViewStat Thermostat CommandsDay Forecast Commands Weather Condition KeywordsAxLink Commands AxLink CommandsDew Point 55F Temperature scaleDisplays the current forecast To Off, the response reports OFFSendcommand ’LK MR1 TR3’ Sets the mode to Program Master requesting the thermostat’s serial number Sets the current barometric pressureRequest the thermostat’s serial number Thermostat returns the serial numberAxLink Channels AxLink ChannelsHeat 224 219Hvac State Emergency 2nd stage heat relay Provides feedback from relay W2 246Weather Duet Module AxLink LevelsAxLink Levels Weather Setup Pages InConcert windowChanging the Date and Time Weather MainChanging the Humidity Settings Changing the Humidity ModeChanging the Heat and Cool Settings Humidity menuChanging the Hvac Mode Hvac Mode menuChanging the Hold Mode Entering Location by Zip CodeChanging Wind Speed Units Changing Temperature UnitsEntering Location by Station ID Changing Pressure UnitsDay Forecast screen Programming ENV-VST-C Operation / Reference Guide Increase Your Revenue through education + knowledge
Related manuals
Manual 2 pages 4.04 Kb

ENV-VST-C specifications

The AMX ENV-VST-C is an advanced video streaming and encoding solution designed to meet the needs of modern broadcasting and professional video applications. Known for its high-performance capabilities and seamless integration into existing systems, the ENV-VST-C stands as a reliable choice for content creators, broadcasters, and businesses alike.

One of the main features of the AMX ENV-VST-C is its ability to support a wide range of video formats and resolutions. The device is capable of encoding and streaming in 4K, Full HD, and SD resolutions, ensuring that users can produce high-quality content regardless of their specific requirements. This versatility makes it suitable for various applications, including live event streaming, corporate communications, and even online educational platforms.

The ENV-VST-C utilizes state-of-the-art encoding technologies, such as H.264 and H.265, providing users with high-quality video while optimizing bandwidth usage. H.265, in particular, allows for significantly smaller file sizes compared to H.264, all without sacrificing video quality. This efficiency is crucial for users looking to reduce costs associated with bandwidth and storage, especially in environments where video distribution is critical.

Another key characteristic of this encoder is its user-friendly interface. The AMX ENV-VST-C features an intuitive control panel and web interface that allows users to configure settings, monitor performance, and manage live streams effortlessly. This ease of use is essential for operators who may not have in-depth technical knowledge but need to manage complex streaming tasks efficiently.

In addition, the AMX ENV-VST-C supports multiple streaming protocols, including RTMP, RTSP, and MPEG-TS. This capability enables seamless integration with various content delivery networks (CDNs) and ensures that users can reach their audience effectively across different platforms.

Moreover, the device is designed with reliability in mind. It offers features such as redundant power supplies and advanced cooling systems, which help maintain optimal performance even in demanding environments. This reliability is crucial for live streaming applications, where any downtime can result in significant loss of engagement and revenue.

In conclusion, the AMX ENV-VST-C stands out with its robust feature set, cutting-edge technologies, and user-centric design. Whether you are in broadcasting, corporate communication, or education, this encoder provides the performance and flexibility needed to deliver exceptional video content. With its commitment to quality and efficiency, the AMX ENV-VST-C is a valuable asset for anyone looking to enhance their video production capabilities.
Top Page Image Contents