Hearth and Home Technologies SANTAFEI-B owner manual 7Appliance Set-Up, Leveling System

Page 17

R

Santa Fe Pellet Insert

7Appliance Set-Up

A. Leveling System

The leveling bolts are located at the rear of the appliance. To access the bolts, remove the front access panels. Reach in and turn the bolt to the desired height to level the appli- ance.

Leveling Bolt on Each Side

Figure 17.1

B. Outside Air Kit Instructions

Parts Included in Kit: 1 piece of 2 inch x 3 ft. flex hose, 2 hose clamps, 1 collar assembly, 1 termination cap assembly, 1 trim ring, fasteners.

Tools Needed: Phillips head screwdriver; wire cutters; hole saw or jig saw.

1.Measure distance from floor to air vent opening in appli- ance and mark location on wall.

2.Use saw to cut opening in wall. Cut a 2-1/2 to 3 inch (64-76mm) opening on inside wall and a 3 to 3-1/2 inch

(76-89mm) opening on outside of house.

3.Use hose clamp to secure flex pipe to collar assembly.

4.Slide trim ring over flex pipe and run pipe through wall.

5.Attach hose to outside termination cap with second hose clamp.

6.Secure termination cap to outside surface.

7.Secure trim ring to interior wall.

CAUTION

Never draw outside combustion air from:

•Wall, floor or ceiling cavity

•Enclosed space such as an attic or garage

Figure 17.2

Air Intake Channel

Trim Ring

Termination

 

Cap Assembly

Flex Hose

Hose Clamp

Collar

Hose Clamp

Assembly

September 1, 2008

7019-205C

Page 17

Page 16 Page 18
Image 17
Page 16 Page 18
Contents Hot glass will cause burns Santa FE Pellet InsertSanta Fe Pellet Insert Behind left access panelLocation On chain behind right access panel Table of Contents Appliance Certification BTU & Efficiency Specifications Listing and Code ApprovalsMobile Home Approved Glass SpecificationsAppliance Location Design, Installation & Location ConsiderationsGetting Started Negative Pressure Santa Fe Pellet Insert Locating Your Appliance & ChimneyDraft Inspect Appliance & Components and Pre-Use Check List Santa Fe Pellet Insert Fire SafetyTools And Supplies Needed Appliance Dimensions 3Dimensions and ClearancesShown with Rear Vent and Optional Outside Air Santa Fe Pellet Insert Clearance To Combustibles, UL and ULCMantel De 12 inc Floor ProtectionMinimum Opening for Masonry and Zero Clearance Fireplaces Starter hole Mark area of floor to cut Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartSanta Fe Pellet Insert Equivalent Feet of Pipe 5Venting Systems Side panel removed Santa Fe Pellet Insert Full Reline With Outside AirSide view of Santa Fe Insert with 6Mobile Home Mobile Home InstallationOutside Air Kit Instructions 7Appliance Set-UpLeveling System Grille Bracket Cover Door Removal Door Trim InstallationDoor Handle Removal Size 9d x 45w, 2 to 10 Height Adjustment Santa Fe Pellet Insert Adjustable Hearth SupportCompleted View Santa Fe Pellet Insert Panel and Trim SetOptional Firepot Top Log Installation Four Piece Log Set InstallationLeft Side Santa Fe Pellet Insert Thermostat InstallationGeneral Operating Information Operating InstructionsFuel Size And Material Feed Rate Adjustment Instructions Fire CharacteristicsSanta Fe Pellet Insert Before Your First Fire Starting Your First FireSanta Fe Pellet Insert Ignition Cycles Frequently Asked QuestionsPossible Cause Corrective Action 9TroubleshootingSymptom Page Symptom Possible Cause Corrective Action 10Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartFrequency Daily Weekly Monthly Yearly Types of FuelCleaning Ash Drawer Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As neededDoor Latch Inspection Cleaning Beneath Heat ExchangerCleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonArning Santa Fe Pellet Insert High Ash Fuel Content MaintenanceConvection Blower Replacement Santa Fe Pellet Insert Blower ReplacementCombustion Exhaust Blower Replacement Santa Fe Pellet Insert Igniter Replacement Glass Replacement Santa Fe Pellet Insert Baffle & Brick Set Removal Re-installing Baffle & Brick SetHook on left side Tab on right side Component Function Reference MaterialsWiring Harnes See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FComponent Locations Right Side Cleaning Rods & Heat Exchanger TubesDescription Part Number Santa Fe Pellet Insert Exploded ViewsSanta Fe Pellet Insert Item No Service Parts, Alphabetical Order Santa Fe Pellet Insert Service Parts and AccessoriesSCRAPER-SFI Santa Fe Pellet Insert, Black Grilles Item No Accessories, Alphabetical OrderItem No Appliance Date of Service Performed By Description of Service Santa Fe Pellet Insert Service And Maintenance LogSanta Fe Pellet Insert Service And Maintenance Log Cont’d Santa Fe Pellet Insert Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Santa Fe Pellet Insert Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d T O T O

SANTAFEI-B specifications

Hearth and Home Technologies SANTAFEI-B is a standout fireplace option renowned for its intelligent design, efficiency, and ease of use. This innovative fireplace blends modern technology with classic aesthetic appeal, making it a popular choice for homeowners seeking ambiance and functionality.

One of the standout features of the SANTAFEI-B is its high-efficiency design. With an efficiency rating that significantly exceeds traditional fireplaces, this model maximizes heat output while minimizing fuel consumption. This efficiency not only translates into lower heating bills but also means that the energy used is effectively converted into warmth for your living space.

The SANTAFEI-B incorporates advanced technology such as the IntelliFire™ ignition system, which offers easy start-up and reliable operation. This technology simplifies the process of lighting the fire and maintaining it, allowing users to enjoy a warm and inviting atmosphere with minimal effort. Additionally, the system is equipped with remote control options for enhanced convenience, enabling users to adjust the flames and heat from the comfort of their seat.

Design-wise, the SANTAFEI-B is available in various styles and finishes, ensuring it can seamlessly fit into any home decor. The customizable options allow homeowners to express their personal style, whether they prefer a sleek modern look or a more traditional aesthetic. The large viewing area provides a stunning display of the flames, creating an inviting focal point in any room.

Moreover, the fireplace is fitted with a variety of safety features that make it a reliable choice for families. These features include safety screens and automatic shut-off mechanisms that ensure peace of mind when using this appliance.

In terms of maintenance, the SANTAFEI-B is designed for easy cleaning and upkeep. Durable materials are used in its construction, which not only enhances its longevity but also makes it simple to maintain its appearance.

In summary, Hearth and Home Technologies SANTAFEI-B is a sophisticated fireplace that combines efficiency, modern technology, and stylish design. With features designed for safety and convenience, it stands out as an excellent choice for anyone looking to enhance their home with a beautiful and functional heating solution. The SANTAFEI-B truly represents the best of both worlds, marrying warmth and comfort with contemporary living.
Top Page Image Contents