Hearth and Home Technologies SANTAFEI-B Santa Fe Pellet Insert Panel and Trim Set, Completed View

Page 21

R

Santa Fe Pellet Insert

H. Panel and Trim Set

1.Lay panel top and legs face down on protective cov- ering to prevent scratching.

1.

Attach the panel legs to the top panel using a Phillips

 

head screwdriver. There are 2 screws for each leg.

 

Figure 21.2.

2.

Open the hopper lid by pulling toward you. This will

 

make it easier to set the panels in place. Secure the

 

panels to the insert, 2 screws per leg, as shown in

 

Figure 21.3.

3.

Connect the trim pieces together using the “L” Brack-

 

ets supplied. Figure 21.4.

4.

Slide the trim over the top of the panels.

5.

Install the access panels. At the bottom of the access

 

panel there are 2 hooks that slip into a slot at the

Attach panel legs to top

Figure 21.2

bottom of the side panel and a magnet at the top that

holds the access panel in place. Figure 21.3.

Open Hopper Lid for

Easier Placement of

Panel Set

Access Panels

Hook

Magnet

Side

Panel

Access Panel

Figure 21.3

View of "L" Bracket

installed

Figure 21.1- Completed View

Figure 20.4

September 1, 2008

7019-205C

Page 21

Page 20 Page 22
Image 21
Page 20 Page 22
Contents Hot glass will cause burns Santa FE Pellet InsertBehind left access panel Location On chain behind right access panelSanta Fe Pellet Insert Table of Contents Appliance Certification BTU & Efficiency Specifications Listing and Code ApprovalsMobile Home Approved Glass SpecificationsDesign, Installation & Location Considerations Getting StartedAppliance Location Santa Fe Pellet Insert Locating Your Appliance & Chimney DraftNegative Pressure Santa Fe Pellet Insert Fire Safety Tools And Supplies NeededInspect Appliance & Components and Pre-Use Check List Appliance Dimensions 3Dimensions and ClearancesShown with Rear Vent and Optional Outside Air Santa Fe Pellet Insert Clearance To Combustibles, UL and ULCFloor Protection Minimum Opening for Masonry and Zero Clearance FireplacesMantel De 12 inc Starter hole Mark area of floor to cut 4Vent Information Chimney and Exhaust ConnectionVenting Termination Requirements Pipe Selection Chart Santa Fe Pellet Insert Equivalent Feet of PipeExample of 3 Elbow-Rear Vent Termination Calculation 5Venting Systems Santa Fe Pellet Insert Full Reline With Outside Air Side view of Santa Fe Insert withSide panel removed 6Mobile Home Mobile Home Installation7Appliance Set-Up Leveling SystemOutside Air Kit Instructions Grille Bracket Cover Door Trim Installation Door Handle RemovalDoor Removal Size 9d x 45w, 2 to 10 Height Adjustment Santa Fe Pellet Insert Adjustable Hearth SupportCompleted View Santa Fe Pellet Insert Panel and Trim SetOptional Firepot Top Log Installation Four Piece Log Set InstallationLeft Side Santa Fe Pellet Insert Thermostat InstallationOperating Instructions Fuel Size And MaterialGeneral Operating Information Feed Rate Adjustment Instructions Fire CharacteristicsSanta Fe Pellet Insert Before Your First Fire Starting Your First FireSanta Fe Pellet Insert Ignition Cycles Frequently Asked Questions9Troubleshooting SymptomPossible Cause Corrective Action Page Symptom Possible Cause Corrective Action 10Maintaining & Servicing Your Appliance Quick Reference Maintenance ChartFrequency Daily Weekly Monthly Yearly Types of FuelCleaning Ash Drawer Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As neededDoor Latch Inspection Cleaning Beneath Heat ExchangerCleaning Exhaust Blower Requires No Lubrication Cleaning the HopperCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonArning Santa Fe Pellet Insert High Ash Fuel Content MaintenanceSanta Fe Pellet Insert Blower Replacement Combustion Exhaust Blower ReplacementConvection Blower Replacement Santa Fe Pellet Insert Igniter Replacement Glass Replacement Santa Fe Pellet Insert Baffle & Brick Set Removal Re-installing Baffle & Brick SetHook on left side Tab on right side Component Function Reference MaterialsWiring Harnes See .1 below Vacuum SwitchSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FComponent Locations Right Side Cleaning Rods & Heat Exchanger TubesDescription Part Number Santa Fe Pellet Insert Exploded ViewsSanta Fe Pellet Insert Item No Service Parts, Alphabetical Order Santa Fe Pellet Insert Service Parts and AccessoriesSCRAPER-SFI Item No Accessories, Alphabetical Order Item No ApplianceSanta Fe Pellet Insert, Black Grilles Date of Service Performed By Description of Service Santa Fe Pellet Insert Service And Maintenance LogSanta Fe Pellet Insert Service And Maintenance Log Cont’d Santa Fe Pellet Insert Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Santa Fe Pellet Insert Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d T O T O

SANTAFEI-B specifications

Hearth and Home Technologies SANTAFEI-B is a standout fireplace option renowned for its intelligent design, efficiency, and ease of use. This innovative fireplace blends modern technology with classic aesthetic appeal, making it a popular choice for homeowners seeking ambiance and functionality.

One of the standout features of the SANTAFEI-B is its high-efficiency design. With an efficiency rating that significantly exceeds traditional fireplaces, this model maximizes heat output while minimizing fuel consumption. This efficiency not only translates into lower heating bills but also means that the energy used is effectively converted into warmth for your living space.

The SANTAFEI-B incorporates advanced technology such as the IntelliFire™ ignition system, which offers easy start-up and reliable operation. This technology simplifies the process of lighting the fire and maintaining it, allowing users to enjoy a warm and inviting atmosphere with minimal effort. Additionally, the system is equipped with remote control options for enhanced convenience, enabling users to adjust the flames and heat from the comfort of their seat.

Design-wise, the SANTAFEI-B is available in various styles and finishes, ensuring it can seamlessly fit into any home decor. The customizable options allow homeowners to express their personal style, whether they prefer a sleek modern look or a more traditional aesthetic. The large viewing area provides a stunning display of the flames, creating an inviting focal point in any room.

Moreover, the fireplace is fitted with a variety of safety features that make it a reliable choice for families. These features include safety screens and automatic shut-off mechanisms that ensure peace of mind when using this appliance.

In terms of maintenance, the SANTAFEI-B is designed for easy cleaning and upkeep. Durable materials are used in its construction, which not only enhances its longevity but also makes it simple to maintain its appearance.

In summary, Hearth and Home Technologies SANTAFEI-B is a sophisticated fireplace that combines efficiency, modern technology, and stylish design. With features designed for safety and convenience, it stands out as an excellent choice for anyone looking to enhance their home with a beautiful and functional heating solution. The SANTAFEI-B truly represents the best of both worlds, marrying warmth and comfort with contemporary living.
Top Page Image Contents