Hearth and Home Technologies SANTAFEI-B Door Handle Removal, Door Trim Installation, Door Removal

Page 19

R

D. Door Handle Removal

Tools Requied: 5/32 Allen wrench

NOTE: The door handle must be removed before the trim ring can be installed.

1.Open the door. Using a 5/32 Allen wrench, loosen set screw by a couple of turns, but do not remove.

Figure 19.1.

2.Push the pin completely out and remove the handle.

3.Re-install in reverse order.

E. Door Trim Installation

Tools Required: Phillips head screwdriver. (A stubby screwdriver required if door is still installed on the insert).

1. Remove the door handle first by following the instructions above. Using a Phillips head screwdriver, remove the 2 screws on the top and bottom of the face. Figure 19.1.

Santa Fe Pellet Insert

Figure 19.1

2. Pull the face away from the door by rotating the face toward you from the hinge side first. Carefully push the door handle through the opening on the face.

3. Lay the face (face up) on a protected surface to avoid scratching the trim when installing it in step 5.

4. Line up the studs on the trim with the holes in the face and push studs into the holes.

5. Turn the face and trim over. Secure with 6 nuts provided. Do not overtighten.

6. Thread the door handle through the face opening and insert the pin through the door handle and door latch. Re-tighten the set screw.

7. Re-attach to the door using the same 4 screws previously removed.

F. Door Removal

1.Remove the door handle and face. Follow instructions from D and E above.

2.The door can now be lifted off the hinges.

3.Re-install in reverse order.

September 1, 2008

7019-205C

Page 19

Page 18 Page 20
Image 19
Page 18 Page 20
Contents Hot glass will cause burns Santa FE Pellet InsertLocation On chain behind right access panel Behind left access panelSanta Fe Pellet Insert Table of Contents Glass Specifications Listing and Code ApprovalsAppliance Certification BTU & Efficiency Specifications Mobile Home ApprovedGetting Started Design, Installation & Location ConsiderationsAppliance Location Draft Santa Fe Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Tools And Supplies Needed Santa Fe Pellet Insert Fire SafetyInspect Appliance & Components and Pre-Use Check List Appliance Dimensions 3Dimensions and ClearancesShown with Rear Vent and Optional Outside Air Santa Fe Pellet Insert Clearance To Combustibles, UL and ULCMinimum Opening for Masonry and Zero Clearance Fireplaces Floor ProtectionMantel De 12 inc Starter hole Mark area of floor to cut Chimney and Exhaust Connection 4Vent InformationVenting Termination Requirements Santa Fe Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation 5Venting Systems Side view of Santa Fe Insert with Santa Fe Pellet Insert Full Reline With Outside AirSide panel removed 6Mobile Home Mobile Home InstallationLeveling System 7Appliance Set-UpOutside Air Kit Instructions Grille Bracket Cover Door Handle Removal Door Trim InstallationDoor Removal Size 9d x 45w, 2 to 10 Height Adjustment Santa Fe Pellet Insert Adjustable Hearth SupportCompleted View Santa Fe Pellet Insert Panel and Trim SetOptional Firepot Top Log Installation Four Piece Log Set InstallationLeft Side Santa Fe Pellet Insert Thermostat InstallationFuel Size And Material Operating InstructionsGeneral Operating Information Starting Your First Fire Fire CharacteristicsFeed Rate Adjustment Instructions Santa Fe Pellet Insert Before Your First FireSanta Fe Pellet Insert Ignition Cycles Frequently Asked QuestionsSymptom 9TroubleshootingPossible Cause Corrective Action Page Symptom Possible Cause Corrective Action Types of Fuel Quick Reference Maintenance Chart10Maintaining & Servicing Your Appliance Frequency Daily Weekly Monthly YearlyDisposal of Ashes Frequency As needed Cleaning Firepot with Cleaning Rod & Firepot Clean-Out ToolCleaning Ash Drawer See .1 on Ash Removal from FireboxDoor Latch Inspection Cleaning Beneath Heat ExchangerPreparing Firebox for Non-Burn Season Cleaning the HopperCleaning Exhaust Blower Requires No Lubrication Cleaning Convection Blower Requires No LubricationArning Santa Fe Pellet Insert High Ash Fuel Content MaintenanceCombustion Exhaust Blower Replacement Santa Fe Pellet Insert Blower ReplacementConvection Blower Replacement Santa Fe Pellet Insert Igniter Replacement Glass Replacement Santa Fe Pellet Insert Baffle & Brick Set Removal Re-installing Baffle & Brick SetHook on left side Tab on right side Component Function Reference MaterialsSnap Disc #2 Fuel Delivery Interrupt 250F Vacuum SwitchWiring Harnes See .1 below Snap Disc #1 Convection Blower 110FComponent Locations Right Side Cleaning Rods & Heat Exchanger TubesDescription Part Number Santa Fe Pellet Insert Exploded ViewsSanta Fe Pellet Insert Item No Service Parts, Alphabetical Order Santa Fe Pellet Insert Service Parts and AccessoriesSCRAPER-SFI Item No Appliance Item No Accessories, Alphabetical OrderSanta Fe Pellet Insert, Black Grilles Date of Service Performed By Description of Service Santa Fe Pellet Insert Service And Maintenance LogSanta Fe Pellet Insert Service And Maintenance Log Cont’d Santa Fe Pellet Insert Homeowner’s Notes CONDITIONS, Exclusions & Limitation of Liability Santa Fe Pellet Insert Warranty PolicyHearth & Home Technologies Limited Warranty Cont’d T O T O

SANTAFEI-B specifications

Hearth and Home Technologies SANTAFEI-B is a standout fireplace option renowned for its intelligent design, efficiency, and ease of use. This innovative fireplace blends modern technology with classic aesthetic appeal, making it a popular choice for homeowners seeking ambiance and functionality.

One of the standout features of the SANTAFEI-B is its high-efficiency design. With an efficiency rating that significantly exceeds traditional fireplaces, this model maximizes heat output while minimizing fuel consumption. This efficiency not only translates into lower heating bills but also means that the energy used is effectively converted into warmth for your living space.

The SANTAFEI-B incorporates advanced technology such as the IntelliFire™ ignition system, which offers easy start-up and reliable operation. This technology simplifies the process of lighting the fire and maintaining it, allowing users to enjoy a warm and inviting atmosphere with minimal effort. Additionally, the system is equipped with remote control options for enhanced convenience, enabling users to adjust the flames and heat from the comfort of their seat.

Design-wise, the SANTAFEI-B is available in various styles and finishes, ensuring it can seamlessly fit into any home decor. The customizable options allow homeowners to express their personal style, whether they prefer a sleek modern look or a more traditional aesthetic. The large viewing area provides a stunning display of the flames, creating an inviting focal point in any room.

Moreover, the fireplace is fitted with a variety of safety features that make it a reliable choice for families. These features include safety screens and automatic shut-off mechanisms that ensure peace of mind when using this appliance.

In terms of maintenance, the SANTAFEI-B is designed for easy cleaning and upkeep. Durable materials are used in its construction, which not only enhances its longevity but also makes it simple to maintain its appearance.

In summary, Hearth and Home Technologies SANTAFEI-B is a sophisticated fireplace that combines efficiency, modern technology, and stylish design. With features designed for safety and convenience, it stands out as an excellent choice for anyone looking to enhance their home with a beautiful and functional heating solution. The SANTAFEI-B truly represents the best of both worlds, marrying warmth and comfort with contemporary living.
Top Page Image Contents