Hearth and Home Technologies SANTAFEI-B Santa Fe Pellet Insert Adjustable Hearth Support

Page 20

Santa Fe Pellet Insert

 

R

 

 

G. Adjustable Hearth Support

EXPLODED VIEW OF SCISSORS

 

Size: 9”d x 45”w, 2” to 10” Height Adjustment

 

 

Included in Kit: (1) trim top, (1) trim front, (2) trim sides,

 

 

double-sided tape (already installed)

 

SCREWS ARE CIRCLED

Tools Needed: Phillips head screwdriver, sheet metal

 

 

shears, measuring tape, gloves

 

 

1. The 10 screws on each set of scissors will already be

DOUBLE-SIDED TAPE

DOUBLE-SIDED TAPE

loose when shipped. Figure 20.1.

Figure 20.1

 

 

 

2.Expand scissors to desired height. Tighten screws to hold in place using Phillips head screwdriver. Figure

20.2.

EXPAND SCISSORS TO DESIRED HEIGHT

3. Measure front and side trims to required height to cover scissors and mark pieces for cutting. Cut excess material from top of trim’s edge, not bottom. This edge will be sharp; wear gloves to prevent injury to your hands. Figure 20.3.

 

 

 

 

 

 

 

 

 

 

 

 

 

CUT TOP EDGE OF TRIM,

 

 

 

 

 

 

 

 

 

 

 

 

 

4. Using sheet metal shears, cut trim along the marked

INSTALL FRONT TRIM LAST.

 

NOT BOTTOM EDGE

edge. The cut edge fits under lip of top trim, so it

CORNERS OVERLAP SIDE

 

 

 

 

 

TRIM PIECES

 

 

allows for some variance in your straight edge.

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

Figure 20.2

5.The double-sided tape that holds front and side trims to scissors has a powerful bonding adhesive. Adjust-

ments are extremely difficult once trim has adhered to tape. Do a dry run first without removing paper from tape.

6.

Place cut edge of trim under top lip and into position

Decorative tile

 

on scissors. Place side pieces on first and then front

may be installed

 

piece. The front piece overlaps side pieces.

 

7.

Once you are satisfied with the positioning, remove

 

 

trim and set aside.

 

8.

Remove the paper from double-sided tape that is

Figure 20.3

 

to accept trim side. Align side and then press hard

 

against tape to secure side piece. Repeat for other

 

 

side. Install front trim piece last.

 

9. There are 3 holes in the back flange of the top to secure it to the wall if necessary. Use the appropriate fastener for the type of wall material, i.e., brick, sheet- rock, etc.

NOTE: 3/8 inch (9.5mm) thick tile or like material can be cut to size and fit under lip of top trim edge for a decorative touch. Figure 20.3.

WARNING

Sheet metal trim edges will be sharp.

For safety purposes wear gloves.

Injury can occur.

Figure 20.4

Page 20

7019-205C

September 1, 2008

Page 19 Page 21
Image 20
Page 19 Page 21
Contents Santa FE Pellet Insert Hot glass will cause burnsSanta Fe Pellet Insert Behind left access panelLocation On chain behind right access panel Table of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsMobile Home Approved Glass SpecificationsAppliance Location Design, Installation & Location ConsiderationsGetting Started Negative Pressure Santa Fe Pellet Insert Locating Your Appliance & ChimneyDraft Inspect Appliance & Components and Pre-Use Check List Santa Fe Pellet Insert Fire SafetyTools And Supplies Needed 3Dimensions and Clearances Appliance DimensionsSanta Fe Pellet Insert Clearance To Combustibles, UL and ULC Shown with Rear Vent and Optional Outside AirMantel De 12 inc Floor ProtectionMinimum Opening for Masonry and Zero Clearance Fireplaces Starter hole Mark area of floor to cut Venting Termination Requirements 4Vent InformationChimney and Exhaust Connection Example of 3 Elbow-Rear Vent Termination Calculation Pipe Selection ChartSanta Fe Pellet Insert Equivalent Feet of Pipe 5Venting Systems Side panel removed Santa Fe Pellet Insert Full Reline With Outside AirSide view of Santa Fe Insert with Mobile Home Installation 6Mobile HomeOutside Air Kit Instructions 7Appliance Set-UpLeveling System Grille Bracket Cover Door Removal Door Trim InstallationDoor Handle Removal Santa Fe Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentSanta Fe Pellet Insert Panel and Trim Set Completed ViewFour Piece Log Set Installation Optional Firepot Top Log InstallationSanta Fe Pellet Insert Thermostat Installation Left SideGeneral Operating Information Operating InstructionsFuel Size And Material Fire Characteristics Feed Rate Adjustment InstructionsSanta Fe Pellet Insert Before Your First Fire Starting Your First FireFrequently Asked Questions Santa Fe Pellet Insert Ignition CyclesPossible Cause Corrective Action 9TroubleshootingSymptom Page Symptom Possible Cause Corrective Action Quick Reference Maintenance Chart 10Maintaining & Servicing Your ApplianceFrequency Daily Weekly Monthly Yearly Types of FuelCleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash DrawerSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Door Latch InspectionCleaning the Hopper Cleaning Exhaust Blower Requires No LubricationCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonSanta Fe Pellet Insert High Ash Fuel Content Maintenance ArningConvection Blower Replacement Santa Fe Pellet Insert Blower ReplacementCombustion Exhaust Blower Replacement Santa Fe Pellet Insert Igniter Replacement Glass Replacement Re-installing Baffle & Brick Set Santa Fe Pellet Insert Baffle & Brick Set RemovalHook on left side Tab on right side Reference Materials Component FunctionVacuum Switch Wiring Harnes See .1 belowSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCleaning Rods & Heat Exchanger Tubes Component Locations Right SideSanta Fe Pellet Insert Exploded Views Description Part NumberSanta Fe Pellet Insert Santa Fe Pellet Insert Service Parts and Accessories Item No Service Parts, Alphabetical OrderSCRAPER-SFI Santa Fe Pellet Insert, Black Grilles Item No Accessories, Alphabetical OrderItem No Appliance Santa Fe Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceSanta Fe Pellet Insert Service And Maintenance Log Cont’d Santa Fe Pellet Insert Homeowner’s Notes Santa Fe Pellet Insert Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d T O T O

SANTAFEI-B specifications

Hearth and Home Technologies SANTAFEI-B is a standout fireplace option renowned for its intelligent design, efficiency, and ease of use. This innovative fireplace blends modern technology with classic aesthetic appeal, making it a popular choice for homeowners seeking ambiance and functionality.

One of the standout features of the SANTAFEI-B is its high-efficiency design. With an efficiency rating that significantly exceeds traditional fireplaces, this model maximizes heat output while minimizing fuel consumption. This efficiency not only translates into lower heating bills but also means that the energy used is effectively converted into warmth for your living space.

The SANTAFEI-B incorporates advanced technology such as the IntelliFire™ ignition system, which offers easy start-up and reliable operation. This technology simplifies the process of lighting the fire and maintaining it, allowing users to enjoy a warm and inviting atmosphere with minimal effort. Additionally, the system is equipped with remote control options for enhanced convenience, enabling users to adjust the flames and heat from the comfort of their seat.

Design-wise, the SANTAFEI-B is available in various styles and finishes, ensuring it can seamlessly fit into any home decor. The customizable options allow homeowners to express their personal style, whether they prefer a sleek modern look or a more traditional aesthetic. The large viewing area provides a stunning display of the flames, creating an inviting focal point in any room.

Moreover, the fireplace is fitted with a variety of safety features that make it a reliable choice for families. These features include safety screens and automatic shut-off mechanisms that ensure peace of mind when using this appliance.

In terms of maintenance, the SANTAFEI-B is designed for easy cleaning and upkeep. Durable materials are used in its construction, which not only enhances its longevity but also makes it simple to maintain its appearance.

In summary, Hearth and Home Technologies SANTAFEI-B is a sophisticated fireplace that combines efficiency, modern technology, and stylish design. With features designed for safety and convenience, it stands out as an excellent choice for anyone looking to enhance their home with a beautiful and functional heating solution. The SANTAFEI-B truly represents the best of both worlds, marrying warmth and comfort with contemporary living.
Top Page Image Contents