Hearth and Home Technologies SANTAFEI-B Listing and Code Approvals, Mobile Home Approved

Page 4

R

Santa Fe Pellet Insert

 

1 Listing and Code Approvals

 

 

 

 

A. Appliance Certification

E. BTU & Efficiency Specifications

 

MODEL:

Santa Fe Pellet Insert

LABORATORY:

OMNI Test Laboratories, Inc

REPORT NO.

061-S-62-6

TYPE:

Solid Fuel Room Heater/Pellet Fuel

 

Burning Type Insert

STANDARD:

ASTM E1509-2004, ULC S628-93 and

 

ULC/ORD-C1482-M1990 Room Heater

 

Pellet Fuel Burning Type and (UM) 84-

 

HUD, Mobile Home Approved

Particulate

.7 grams/hr

Emissions Rating:

 

*BTU Output:

8,000 - 30,000 / hr

Heating Capacity:

up to 1,500 sq. ft. depending

 

on climate zone

Hopper Capacity:

45 lbs

Fuel:

Wood Pellets or Shelled Corn

Shipping Weight:

214 lbs

B. Mobile Home Approved

This appliance is approved for mobile home installations when not installed in a sleeping room and when an outside combustion air inlet is provided.

The structural integrity of the mobile home floor, ceiling, and walls must be maintained. The appliance must be properly grounded to the frame of the mobile home and use only listed pellet vent, Class “L” or “PL” connector pipe.

A Quadra-Fire Outside Air Kit must be installed in a mobile home installation.

*BTU output will vary, depending on the brand of fuel you use in your appliance. Consult your Quadra-Fire dealer for best results.

NOTE: Hearth & Home Technologies, manufacturer of this appliance, reserves the right to alter its products, their specifications and/or price without notice.

C. Glass Specifications

This appliance is equipped with 5mm ceramic glass. Replace glass only with 5mm ceramic glass. Please contact your dealer for replacement glass.

NOTE: This installation must conform with local codes. In the absence of local codes you must comply with the ASTM

E1509-2004, ULC S628-93, ULC/ORD-C-1482-M1990, (UM) 84-HUD

D. Electrical Rating

115 VAC, 60 Hz, Start 4.1 Amps, Run 1.1 Amps

Page 4

7019-205C

September 1, 2008

Image 4
Contents Santa FE Pellet Insert Hot glass will cause burnsLocation On chain behind right access panel Behind left access panelSanta Fe Pellet Insert Table of Contents Listing and Code Approvals Appliance Certification BTU & Efficiency SpecificationsMobile Home Approved Glass SpecificationsGetting Started Design, Installation & Location ConsiderationsAppliance Location Draft Santa Fe Pellet Insert Locating Your Appliance & ChimneyNegative Pressure Tools And Supplies Needed Santa Fe Pellet Insert Fire SafetyInspect Appliance & Components and Pre-Use Check List 3Dimensions and Clearances Appliance DimensionsSanta Fe Pellet Insert Clearance To Combustibles, UL and ULC Shown with Rear Vent and Optional Outside AirMinimum Opening for Masonry and Zero Clearance Fireplaces Floor ProtectionMantel De 12 inc Starter hole Mark area of floor to cut Chimney and Exhaust Connection 4Vent InformationVenting Termination Requirements Santa Fe Pellet Insert Equivalent Feet of Pipe Pipe Selection ChartExample of 3 Elbow-Rear Vent Termination Calculation 5Venting Systems Side view of Santa Fe Insert with Santa Fe Pellet Insert Full Reline With Outside AirSide panel removed Mobile Home Installation 6Mobile HomeLeveling System 7Appliance Set-UpOutside Air Kit Instructions Grille Bracket Cover Door Handle Removal Door Trim InstallationDoor Removal Santa Fe Pellet Insert Adjustable Hearth Support Size 9d x 45w, 2 to 10 Height AdjustmentSanta Fe Pellet Insert Panel and Trim Set Completed ViewFour Piece Log Set Installation Optional Firepot Top Log InstallationSanta Fe Pellet Insert Thermostat Installation Left SideFuel Size And Material Operating InstructionsGeneral Operating Information Fire Characteristics Feed Rate Adjustment InstructionsSanta Fe Pellet Insert Before Your First Fire Starting Your First FireFrequently Asked Questions Santa Fe Pellet Insert Ignition CyclesSymptom 9TroubleshootingPossible Cause Corrective Action Page Symptom Possible Cause Corrective Action Quick Reference Maintenance Chart 10Maintaining & Servicing Your ApplianceFrequency Daily Weekly Monthly Yearly Types of FuelCleaning Firepot with Cleaning Rod & Firepot Clean-Out Tool Cleaning Ash DrawerSee .1 on Ash Removal from Firebox Disposal of Ashes Frequency As neededCleaning Beneath Heat Exchanger Door Latch InspectionCleaning the Hopper Cleaning Exhaust Blower Requires No LubricationCleaning Convection Blower Requires No Lubrication Preparing Firebox for Non-Burn SeasonSanta Fe Pellet Insert High Ash Fuel Content Maintenance ArningCombustion Exhaust Blower Replacement Santa Fe Pellet Insert Blower ReplacementConvection Blower Replacement Santa Fe Pellet Insert Igniter Replacement Glass Replacement Re-installing Baffle & Brick Set Santa Fe Pellet Insert Baffle & Brick Set RemovalHook on left side Tab on right side Reference Materials Component FunctionVacuum Switch Wiring Harnes See .1 belowSnap Disc #1 Convection Blower 110F Snap Disc #2 Fuel Delivery Interrupt 250FCleaning Rods & Heat Exchanger Tubes Component Locations Right SideSanta Fe Pellet Insert Exploded Views Description Part NumberSanta Fe Pellet Insert Santa Fe Pellet Insert Service Parts and Accessories Item No Service Parts, Alphabetical OrderSCRAPER-SFI Item No Appliance Item No Accessories, Alphabetical OrderSanta Fe Pellet Insert, Black Grilles Santa Fe Pellet Insert Service And Maintenance Log Date of Service Performed By Description of ServiceSanta Fe Pellet Insert Service And Maintenance Log Cont’d Santa Fe Pellet Insert Homeowner’s Notes Santa Fe Pellet Insert Warranty Policy CONDITIONS, Exclusions & Limitation of LiabilityHearth & Home Technologies Limited Warranty Cont’d T O T O

SANTAFEI-B specifications

Hearth and Home Technologies SANTAFEI-B is a standout fireplace option renowned for its intelligent design, efficiency, and ease of use. This innovative fireplace blends modern technology with classic aesthetic appeal, making it a popular choice for homeowners seeking ambiance and functionality.

One of the standout features of the SANTAFEI-B is its high-efficiency design. With an efficiency rating that significantly exceeds traditional fireplaces, this model maximizes heat output while minimizing fuel consumption. This efficiency not only translates into lower heating bills but also means that the energy used is effectively converted into warmth for your living space.

The SANTAFEI-B incorporates advanced technology such as the IntelliFire™ ignition system, which offers easy start-up and reliable operation. This technology simplifies the process of lighting the fire and maintaining it, allowing users to enjoy a warm and inviting atmosphere with minimal effort. Additionally, the system is equipped with remote control options for enhanced convenience, enabling users to adjust the flames and heat from the comfort of their seat.

Design-wise, the SANTAFEI-B is available in various styles and finishes, ensuring it can seamlessly fit into any home decor. The customizable options allow homeowners to express their personal style, whether they prefer a sleek modern look or a more traditional aesthetic. The large viewing area provides a stunning display of the flames, creating an inviting focal point in any room.

Moreover, the fireplace is fitted with a variety of safety features that make it a reliable choice for families. These features include safety screens and automatic shut-off mechanisms that ensure peace of mind when using this appliance.

In terms of maintenance, the SANTAFEI-B is designed for easy cleaning and upkeep. Durable materials are used in its construction, which not only enhances its longevity but also makes it simple to maintain its appearance.

In summary, Hearth and Home Technologies SANTAFEI-B is a sophisticated fireplace that combines efficiency, modern technology, and stylish design. With features designed for safety and convenience, it stands out as an excellent choice for anyone looking to enhance their home with a beautiful and functional heating solution. The SANTAFEI-B truly represents the best of both worlds, marrying warmth and comfort with contemporary living.