LG Electronics LT1030CR owner manual Procedure a, Supplied with your unit,skip to step, Trim 2 ea

Page 13

Installation

PROCEDURE A

1	If you are using the new sleeve (optionally
	supplied with your unit),skip to step 3.

Otherwise, install the plastic grille from the kit. Cut the plastic grille to 25-1/2" wide and 15- 1/4" high. Place the plastic grille to the inside of the wall sleeve at the rear flange.

	FIG. 4

2	Fasten the 4 washer screws to secure the grille
	to the wall sleeve. If you need plastic nuts to

mount plastic grille to the inside of the wall sleeve, there are plastic nuts in the installation kit. The nuts are installed from the inside of the sleeve and are pressing into the square holes of the rear flanges.

or

FIG. 5

3 Remove the backing from the Vertical Insulation strip 159/16 x 13/8 x 13/8 and attach that to the inside right of the sleeve as shown below. Remove the backing from the Around Insulation strip 671/8 x 13/8 x 25/32 and attach that to the inside front of the sleeve as shown below.

Indoor	Outdoor
Around Insulation
Vertical Insulation
9 1/2"	6"
	FIG. 6

4	Install the new unit into the wall sleeve.
5	To assemble trim, snap the tab of each piece
	into the slot of the other piece as shown below.

Slide trim over the front of the air conditioner until trim is flush with sleeve as shown below.

Trim (2 ea)

Wall

FIG. 7

•Air conditioners covered in this manual pose an excessive weight hazard. Two or more people are needed to move and install the unit.

To prevent injury or strain, use proper lifting and carrying techniques when moving unit.

•When handling the air conditioner, be careful to avoid cuts from sharp metal fins on front and rear coils.

•Make sure air conditioner does not fall during removal.

•If unit does not operate after installation check, to be sure the circuit interrupter has not been tripped. Refer to the Troubleshooting guide for reset procedure.

ENGLISH

Owner’s Manual 13

Image 13

Contents Room AIR Conditioner Table of Contents Don’t use a power cord, a Always plug into a grounded Safety PrecautionsOutlet Power cord length Is damaged Be caution when unpacking and installingSounds, odors, or smoke Unplug the unit if strangeCome from it During operation Ventilate the room well whenKeep level parallel in installing the product Hold the plug by the head When gas leaks, openOtherwise, it may cause vibration or water leakage It will cause electric shock or fireDo not block the inlet or outlet of air flow Sharp edges when Perform ventilation Installing SometimesDo not step on Always insert the filter Be cautious not to touchService Cleaning and MaintenanceBefore Operation Preparing for OperationFeatures Symbols Used in this ManualIntroduction Use Wall Receptacle Power Supply Electrical SafetyElectrical Data Wash hands after handlingPlease Read Carefully Electrical SafetyInstallation Requirements InstallationHOW to Install InstallationInstall the new unit into the wall sleeve Procedure aSupplied with your unit,skip to step To the wall sleeve. If you need plastic nuts toTop View Procedure BFasten the screws Wall Procedure aRemove the backing from the Horizontal Procedure CRemove the backing from the support blocks Remove the backing from the 1113/16 shim To achieve rearward slope for unit drainingControls Operating InstructionsIncrements of 1 F Remote controlFAN Fan-only operation Ventilation How to insert BatteriesAir Direction Air Filter Cleaning Maintenance and ServiceHow to Attach Front Grille to Cabinet Troubleshooting Common Problems and SolutionsNormal Operation Memo Modelo n Serie n Escriba aquí el modelo y número de serieNombre del distribuidor Fecha de compra Toma a tierra Precauciones de SeguridadNo desmonte ni modifique Tenga cuidado al Los productos AparatoNo ponga el cable de alimentación cerca de un calentador Sostenga el enchufe por su cabeza al sacarlo No dañe ni use un enchufe de alimentación no especificadoMantenga nivelado el producto al instalarlo Puntiagudos al instalar Ocasiones Del aire durante el No se suba a la unidad Inserte siempre el filtroUso Preparación para el funcionamientoLimpieza y mantenimiento ServicioSímbolos Utilizados en Este Manual IntroducciónCaracterísticas Datos Electricos Seguraida ElectricaImportante Favorlea CON Atención Seguraida ElectricaRequisitos DE Instalación InstalacionPeríodo de tiempo Frontal y posteriorCómo Instalar InstalaciónPared Procedimiento aPerspectiva superior Procedimiento BColoque la rejilla plástica Apriete los tornillosProcedimiento a Ajuste la posición según describe el pasoIgual a 18, salte al paso 7. Si no, corte las Procedimiento CDrenaje de la unidad, retire el envoltorio de las Del soporte de paredControles Instruccionnes de FuncionamientoEl ajuste se muestra en pantalla Del ventilador, control de temperatura en 72 FReinicio automático Control remotoIncrementos de 1 F El ajuste aparece en pantallaVentilación Cómo Poner Las BateriasDirección del aire Limpieza del filtro de aire Cuidado y MantenimientoComo agregar la rejilla frontal al gabinete Operación normal Problemas y soluciones habitualesOperación anormal Gire el control de Temperatura a un número más bajoNota Nota Aire Acondicionador Garantía Limitada DEL Aire Acondicionador LG EE.UU Patent No. Us 6, 412 No A21004Q LG Room AIR Conditioner Limited Warranty USA