State Industries 186589-001 Slow HOT Water Recov, Ery, Drip from Relief Valve, Shut OFF

Page 28

PROBLEM

 

POSSIBLE CAUSE(S)

 

CORRECTION

 

1.

Insufficient secondary air

1.

Provide ventilation to water heater. Check

 

 

 

 

flue way, flue baffle and burner

 

2.

Flue clogged

2.

Clean flue, locate source and correct

SLOW HOT WATER RECOV-

3.

Low gas pressure

3.

Check with gas utility company

4.

Improper calibration

4.

Replace gas control/thermostat

ERY

5.

Gas control/thermostat set too low

5.

Turn temperature dial to desired setting

 

 

6.

Water heater too small

6.

Install adequate size heater

 

7.

Wrong piping connections

7.

Correct piping-dip tube must be in cold inlet

 

8.

Wasted hot water

8.

Advise customer

 

1.

Excessive water pressure

1.

Use a pressure reducing valve and relief

 

 

 

 

valve

DRIP FROM RELIEF VALVE

2.

Heater stacking

2.

Lower the thermostat setting

 

3.

Closed water system

3.

See “Closed System/Thermal Expansion”

 

4.

Temperature setting too high

4.

Decrease the temperature setting

THERMOSTAT FAILS TO

1.

Defective gas control/thermostat

1.

Replace gas control/thermostat

SHUT OFF

2.

Improper calibration

2.

Replace gas control/thermostat

 

1.

Insufficient secondary air

1.

Provide ventilation to water heater. Check

COMBUSTION ODORS

 

 

 

flue way, flue baffle, burner

2.

Flue clogged

2.

Clean, locate source and correct

 

 

3.

Heater installed in a confined area

3.

Provide fresh air ventilation

 

1.

Insufficient secondary air

1.

Provide ventilation to water heater. Check

 

 

 

 

flue way, flue baffle, burner

SMOKING AND CARBON

2.

Low gas pressure

2.

Check with gas utility company

3.

Flue clogged

3.

Clean, locate source and correct

FORMATION (SOOTING)

4.

Defective gas control/thermostat

4.

Replace gas control/thermostat

 

 

5.

Heater installed in a confined area

5.

Provide fresh air ventilation

 

6.

Burner flame yellow-lazy

6.

See “Burner Flame Yellow-Lazy”

CONDENSATION

1.

Temperature setting too low

1.

Increase the temperature setting

2.

Water heater too small

2.

Install adequate size heater

 

 

1.

Orifice too large

1.

Replace with correct orifice

BURNER FLAME FLOATS

2.

High gas pressure

2.

Check with gas utility company

3.

Flue clogged

3.

Clean flue and burner-locate source & cor-

AND LIFTS OFF PORTS

 

 

 

rect

 

 

 

 

 

4.

Cold drafts

4.

Locate source and correct

BURNER FLAME TOO HIGH

1.

Orifice too large

1.

Replace with correct orifice

 

1.

Defective gas control/thermostat

1.

Replace gas control/thermostat

FLAME BURNS AT ORIFICE

2.

Low gas pressure

2.

Check with gas utility company

 

3

Orifice not properly installed

3

Reinstall the orifice

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Residential GAS Water Heaters Safe INSTALLATION, USE and Service Important DefinitionsGeneral Safety Table of Contents IntroductionKeep Clear of ALL Obstructions Typical Installation GET to Know Your Water Heater Replacement PartsMixing Valve Usage Hotter Water can ScaldLocating the NEW Water Heater Facts to Consider about the LocationVentilation for Appliances Located in Confined Spaces Insulation BlanketsVent Termination Installing the NEW Water Heater Required AbilityInspect Shipment GeneralTEMPERATURE-PRESSURE Relief Valve Valve and Pipe Insulation if SuppliedClosed Water System Water Potable Heating and Space HeatingGAS Piping GAS Piping with Flexible Connector Sediment Traps Filling the Water Heater High Altitude InstallationsVenting Combustion AIR and Ventilation Vent Terminal ClearancesDV Termination Safety Cover Vent ConnectionsLocating Clearance Hole for Vent High Rise Vent ArrangementVent Assembly Securing Vent Termination Assembly to the Exterior WallStandard Vent Arrangement Uncompressing the Corrugated TubingOffset Vent Arrangement TOP Knob Figure DTemperature Regulation Temperature RegulationFor Your Information External DamageStart UP Conditions Operational ConditionsAIR in HOT Water Faucets Venting System Inspection MaintenancePilot and Main Burner Temperature & Pressure Relief Valve Anode ROD MaintenanceDraining Cathodic Protection AnodeDrain Valve Washer Replacement Service Leakage CheckpointsTroubleshooting Guidelines Problem Possible Causes CorrectionSlow HOT Water Recov ERYDrip from Relief Valve Thermostat Fails toPage Series Tank Parts Conditions and ExceptionsService and Labor Responsibility Claim ProcedureInstallation Information Limitation on Implied WarrantiesTennessee Waltz Parkway Ashland CITY, TN

186589-001 specifications

State Industries 186589-001 is a highly efficient water heater designed to meet both residential and commercial hot water demands. Known for its durability and exceptional performance, this unit is a popular choice among homeowners and business owners alike.

One of the standout features of the State Industries 186589-001 is its robust construction. The tank is made from high-quality materials that offer superior insulation, reducing heat loss and improving overall energy efficiency. This ensures a longer lifespan for the unit while minimizing operating costs. The model also features a glass-lined tank, which prevents corrosion and extends the longevity of the water heater.

The 186589-001 employs innovative heating technologies, including an advanced control system that provides precise temperature regulation. This allows users to set their desired water temperature easily, ensuring optimal comfort and safety. With a powerful heating element, the water heater can quickly heat water to desired levels, providing a reliable supply for various applications, from daily bathing to commercial needs.

Furthermore, the State Industries water heater is equipped with multiple safety features. An automatic shut-off function is integrated to protect against overheating, ensuring user safety during operation. Additionally, the model comes with a pressure relief valve, preventing potential hazards from excessive pressure build-up.

In terms of energy efficiency, the 186589-001 meets and often exceeds current industry standards. Its design minimizes energy consumption, which not only lowers utility bills for users but also aligns with environmentally sustainable practices.

The unit is designed for easy installation, making it convenient for both professionals and DIY enthusiasts. Clear instructions are provided, and the compact size allows it to fit in tight spaces, an advantage for those with limited installation options.

Overall, the State Industries 186589-001 stands as a reliable choice for those seeking a quality water heater with excellent features, advanced technology, and safety characteristics. Its commitment to durability and efficiency makes it a valuable investment for anyone in need of consistent hot water supply.
Top Page Image Contents