State Industries SBD71120NE, THRU SBD85500NE warranty For Your Safety Read Before Operating

Page 26

FOR YOUR SAFETY READ BEFORE OPERATING

WARNING: IF YOU DO NOT FOLLOW THESE INSTRUCTIONS EXACTLYA FIRE OR EXPLOSION MAY RESULT CAUSING PROPERTY DAMAGE, PERSONAL INJURY OR LOSS OF LIFE.

A.THIS APPLIANCE IS EQUIPPED WITH AN IGNITION DEVICE WHICH AUTOMATICALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT THE PILOT BY HAND.

B.BEFORE OPERATING SMELL ALL AROUND THE APPLIANCE AREA FOR GAS . BE SURE TO SMELL NEXT TO THE FLOOR BECAUSE SOME GAS IS HEAVIER THAN AIR AND WILL SETTLE ON THE FLOOR.

WHAT TO DO IF YOU SMELL GAS

•DO NOT TRY TO LIGHT ANY APPLIANCE.

•DO NOT TOUCH ANY ELECTRIC SWITCH

DO NOT USE ANY PHONE IN YOUR BUILDING.

•IMMEDIATELY CALL YOUR GAS SUPPLIER FROM A NEIGHBOR’S PHONE. FOLLOW THE GAS SUPPLIER’S INSTRUCTIONS.

•IF YOU CANNOT REACH YOUR GAS SUPPLIER,

CALL THE FIRE DEPARTMENT.

C.USE ONLY YOUR HAND TO PUSH IN OR TURN THE GAS CONTROL KNOB . NEVER USE TOOLS. IF THE KNOB WILL NOT PUSH IN OR TURN BY HAND, DON’T TRY TO REPAIR IT. CALL A QUALIFIED SERVICE TECHNICIAN. FORCE OR ATTEMPTED REPAIR MAY RESULT IN A FIRE OR EXPLOSION.

D.DO NOT USE THIS APPLIANCE IF ANY PART HAS BEEN UNDER WATER. IMMEDIATELY CALL A QUALIFIED SERVICE TECHNICIAN TO INSPECT THE APPLIANCE AND TO REPLACE ANY PART OF THE CONTROL SYSTEM AND ANY GAS CONTROL WHICH HAS BEEN UNDER WATER.

E.DO NOT OPERATE APPLIANCE UNLESS UNIT IS FILLED WITH WATER AND INLET LINES AFTER FULLY OPEN.

OPERATING

1.STOP! READ THE SAFETY INFORMATION ON THIS LABEL.

2.TURN “OFF“ ALL ELECTRICAL POWER TO THE APPLIANCE. THE FLUE DAMPER WILL AUTOMATICALLY SPRING TO “OPEN” POSITION

3.THIS APPLIANCE IS EQUIPPED WITH AN IGNITION DEVICE WHICH AUTOMATICALLY LIGHTS THE PILOT. DO NOT TRY TO LIGHT THE PILOT BY HAND.

4.REFER TO THE DIAGRAMS ABOVE. TURN TOP KNOB OF THE GAS CONTROL VALVE CLOCKWISE TO “OFF” POSITION (FIG. A).

5.REMOVE THERMOSTAT CONTROL COVER. ROTATE THERMOSTAT DIAL-BY HAND-COUNTERCLOCK-

WISE TO LOWEST SETTING. DO NOT FORCE DIAL OR MECANICAL STOP.

6.WAIT FIVE (5) MINUTES TO CLEAR OUT ANY GAS . IF YOU THEN SMELL GAS:

STOP! FOLLOW “B” IN THE SAFETY INFORMATION ABOVE IN THIS LABEL.

IF YOU DON’T SMELL GAS. GO TO NEXT STEP.

7. TURN GAS CONTROL TOP KNOB

COUNTERCLOCKWISE TO “ON” POSITION, DO NOT FORCE KNOB.

8.TURN ON ALL ELECTRICAL POWER TO THE APPLIANCE.

9.ROTATE APPLIANCE THERMOSTAT DIAL BY HAND DESIRED SETTING. DO NOT FORCE. FLUE DAMPER WILL “OPEN” AND PILOT IGNITION WILL OCCUR. WHEN PILOT IGNITION IS SENSED, THE MAIN BURNER(S) WILL IGNITE.

10.REPLACE THERMOSTAT CONTROL COVER.

11.IF THE APPLIANCE WILL NOT OPERATE. FOLLOW THE INSTRUCTIONS “TO TURN OFF GAS TO APPLIANCE” AND CALL YOUR SERVICE TECHNICIAN OR GAS SUPPLIER.

TO TURN OFF GAS TO APPLIANCE

1.ROTATE THERMOSTAT DIAL -BY HAND- COUNTERCLOCKWISE TO LOWEST SETTING. SEE STEP 5 ABOVE.

2.TURN OFF ALL ELECTRICAL POWER TO THE APPLIANCE IF SERVICE IS TO BE PERFORMED.

3.REMOVE CONTROL ACCESS PANEL.

4.TURN KNOB OF GAS CONTROL VALVE CLOCKWISE TO “OFF” POSITION. SEE STEP 4 ABOVE AND DIAGRAMS.

5.REPLACE CONTROL ACCESS COVERS (SEE STEP 10 ABOVE).

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Models SBD71120NE Thru SBD85500NE ROUGH-IN-DIMENSIONS Canadian Standard Sandblaster BHeater Performance Datasbd Models Heater Performance Datasbd CGA ModelsForeword Table of ContentsGeneral Safety Information Improper Combustion High Altitude InstallationsChemical Vapor Corrosion Liquid Petroleum ModelsHigh Limit Switch E.C.O FeaturesSELF-CLEANING Hydro Cannon RequirementsCirculating Pump Electronic Ignition ControlAutomatic Flue Damper Device Dishwashing Machine RequirementLeveling ClearancesVent Reducer Hard WaterAIR Requirements Water Potable Heating Space Heating VentingMultiple Heater Manifold Relief ValveType B GAS Vent ModelTechnical Data VENTING, Table GAS Pipingand Dirt LEG Installation GAS PipingGAS Meter Size Natural Gases only Grounding InstructionsGAS Pressure Regulator General Installation DIAGRAMS-TOP INLET/OUTLET UsageTube Inlet Installation Code RestrictionsVertical Storage Tank and Forced Circulation Horizontal Storage Tank and Forced CirculationInsert a Installation DIAGRAMS-SIDE INLET/OUTLET Usage Heater with Mixing Valve and Recirculated Sanitizing Loop TWO PRE-HEATERS with Booster Heater Vertical Storage Tank Horizontal Storage TankFour Unit Manifold KIT Manifold KitsTWO Unit Manifold KIT Three Unit Manifold KIT Multiple Unit Installations Single Unit InstallationVent Installation Mechanical VentingPurging OperationFilling To Turn OFF GAS to Appliance For Your Safety Read Before OperatingOperating For Your Safety Read Before Operating Testing Damper Operation Water Temperature ControlAdjustments Checking VentingCheck the Pilot Preventive MaintenancePilot Burner Assembly Main Burner Pilot BurnerTypical Pilot and Main Burner Flames GAS ValvesChecking the Input Anode ROD Inspection Remote Storage Tank Temperature ControlVenting System HOT Water OdorDeliming Solvents Tank Cleanout ProcedureDeliming Using FLO-JUG Method Replacement Parts ServiceTroubleshooting Ignition Module System Electrical ServicingAbnormal Operation Effikal RVGP-KSF-SERIES Flue Damper Trouble Shooting GuideNormal Sequence of Operation PIN END ViewOperational Checklist Complaint Cause Remedy User ServicemanPage Lindahl Parkway, Ashland City, TN Phone 800-821-2017 Fax

THRU SBD85500NE, SBD71120NE specifications

State Industries' SBD71120NE and SBD85500NE are innovative water heaters designed to deliver superior performance and efficiency for residential and commercial applications. These models are part of State Industries' commitment to providing reliable and durable products that meet the diverse needs of consumers.

The SBD71120NE features a capacity of 71 gallons, making it an ideal choice for households with high hot water demand. This model is equipped with advanced insulation technology that minimizes heat loss, ensuring energy efficiency and cost savings over time. With its high energy factor rating, the SBD71120NE not only meets but exceeds the stringent energy efficiency standards set by the Department of Energy. The unit is powered by natural gas, providing quick heating capabilities and a reliable source of hot water when needed.

In contrast, the SBD85500NE has a larger capacity of 85 gallons, catering to larger households or commercial settings with increased hot water requirements. This unit also employs advanced insulation materials that contribute to reduced operating costs and enhanced thermal efficiency. The SBD85500NE utilizes a high-performance power vent system, which facilitates efficient venting of combustion gases and allows for flexible installation options.

Both models are equipped with modern controls, providing users with easy access to temperature settings and diagnostics. The straightforward digital display allows for intuitive adjustments, ensuring optimal water temperature while promoting safety. Furthermore, both units come with a robust warranty, reflecting State Industries' confidence in the durability and longevity of their products.

One of the standout features of the SBD71120NE and SBD85500NE is their compatibility with smart home technology. Integrating these units with a smart thermostat enables users to monitor and manage their hot water usage remotely, thus contributing to more efficient energy consumption.

In conclusion, the State Industries SBD71120NE and SBD85500NE represent cutting-edge technologies and superior craftsmanship. Their respective sizes and capacities make them suitable options for a variety of applications, ensuring reliable hot water delivery while promoting energy efficiency and cost savings. With their advanced features and solid construction, these water heaters are designed to stand the test of time, providing homeowners and businesses with peace of mind and satisfaction.
Top Page Image Contents