State Industries THRU SBD85500NE warranty Installation DIAGRAMS-TOP INLET/OUTLET Usage, General

Page 15

For Canadian installations the electrical connections and grounding shall be done in accordance with current Canadian Electrical Code CSA C22.1, Part 1 and/or local codes.

If any of the original wire as supplied with the appliance must be replaced, use only type 105°C thermoplastic or equivalent. 2500C type F must be used for the flame sensor leads and the spark ignition cable must be high voltage 250°C.

INSTALLATION DIAGRAMS-TOP INLET/OUTLET USAGE

GENERAL

The type, size and location of the relief valves must be in accordance with local codes. The locations of the relief valves shown in the installation diagrams are typical. The heater has a factory installed high temperature limit switch and temperature and pressure relief valve.

Cold water lines to heater should be installed as shown in order to minimize gravity circulation of hot water to building cold water lines.

A listed temperature and pressure relief valve of adequate capacity is installed on the heater. The locations shown in the installation diagrams on the following pages are typical.

The discharge opening of the temperature and pressure relief valve, located in front of the heater must be piped to an open drain and should not be subject to freezing temperatures.

Install in accordance with all local codes.

Use of the top inlet water connection requires installation of an inlet dip tube (refer to figure 12). The tube is supplied in the heater. Follow caution labels if applying heat to this fitting. Do not allow pipe dope to contact the plastic tube during installation.

CODE RESTRICTIONS

Use of the top inlet water connection is not permitted on installations in the state of North Carolina, due to the material of the tube (Polypropylene). Where such code restrictions exist, use only lower inlet tank connection. This may also require a

heat trap - check local codes. The “Top Outlet” connection may still be used on these applications. Plug or cap all unused openings in the tank before filling with water.

DANGER

TEMPERATURE SETTING SHOULD NOT EXCEED SAFE USE TEMPERATURE AT FIXTURES. SEE WATER TEMPERATURE CONTROL WARNING ON PAGE 27. IF HIGHER PREHEAT TEMPERATURES ARE NECESSARY TO OBTAIN ADEQUATE BOOSTER OUTPUT, ADD AN ANTI-SCALD VALVE FOR HOT WATER SUPPLIED TO FIXTURES.

TUBE INLET INSTALLATION

FIGURE 12

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Models SBD71120NE Thru SBD85500NE Canadian Standard Sandblaster B ROUGH-IN-DIMENSIONSHeater Performance Datasbd CGA Models Heater Performance Datasbd ModelsTable of Contents General Safety InformationForeword Liquid Petroleum Models High Altitude InstallationsChemical Vapor Corrosion Improper CombustionRequirements FeaturesSELF-CLEANING Hydro Cannon High Limit Switch E.C.ODishwashing Machine Requirement Electronic Ignition ControlAutomatic Flue Damper Device Circulating PumpClearances LevelingHard Water AIR RequirementsVent Reducer Relief Valve VentingMultiple Heater Manifold Water Potable Heating Space HeatingModel Type B GAS VentTechnical Data VENTING, Table GAS Piping GAS Pipingand Dirt LEG InstallationGrounding Instructions GAS Pressure RegulatorGAS Meter Size Natural Gases only Code Restrictions Installation DIAGRAMS-TOP INLET/OUTLET UsageTube Inlet Installation GeneralHorizontal Storage Tank and Forced Circulation Vertical Storage Tank and Forced CirculationInsert a Installation DIAGRAMS-SIDE INLET/OUTLET Usage Heater with Mixing Valve and Recirculated Sanitizing Loop TWO PRE-HEATERS with Booster Heater Horizontal Storage Tank Vertical Storage TankManifold Kits TWO Unit Manifold KIT Three Unit Manifold KITFour Unit Manifold KIT Mechanical Venting Single Unit InstallationVent Installation Multiple Unit InstallationsOperation FillingPurging For Your Safety Read Before Operating OperatingTo Turn OFF GAS to Appliance For Your Safety Read Before Operating Checking Venting Water Temperature ControlAdjustments Testing Damper OperationPilot Burner Preventive MaintenancePilot Burner Assembly Main Burner Check the PilotGAS Valves Checking the InputTypical Pilot and Main Burner Flames HOT Water Odor Remote Storage Tank Temperature ControlVenting System Anode ROD InspectionTank Cleanout Procedure Deliming Using FLO-JUG MethodDeliming Solvents Electrical Servicing ServiceTroubleshooting Ignition Module System Replacement PartsPIN END View Effikal RVGP-KSF-SERIES Flue Damper Trouble Shooting GuideNormal Sequence of Operation Abnormal OperationComplaint Cause Remedy User Serviceman Operational ChecklistPage Lindahl Parkway, Ashland City, TN Phone 800-821-2017 Fax

THRU SBD85500NE, SBD71120NE specifications

State Industries' SBD71120NE and SBD85500NE are innovative water heaters designed to deliver superior performance and efficiency for residential and commercial applications. These models are part of State Industries' commitment to providing reliable and durable products that meet the diverse needs of consumers.

The SBD71120NE features a capacity of 71 gallons, making it an ideal choice for households with high hot water demand. This model is equipped with advanced insulation technology that minimizes heat loss, ensuring energy efficiency and cost savings over time. With its high energy factor rating, the SBD71120NE not only meets but exceeds the stringent energy efficiency standards set by the Department of Energy. The unit is powered by natural gas, providing quick heating capabilities and a reliable source of hot water when needed.

In contrast, the SBD85500NE has a larger capacity of 85 gallons, catering to larger households or commercial settings with increased hot water requirements. This unit also employs advanced insulation materials that contribute to reduced operating costs and enhanced thermal efficiency. The SBD85500NE utilizes a high-performance power vent system, which facilitates efficient venting of combustion gases and allows for flexible installation options.

Both models are equipped with modern controls, providing users with easy access to temperature settings and diagnostics. The straightforward digital display allows for intuitive adjustments, ensuring optimal water temperature while promoting safety. Furthermore, both units come with a robust warranty, reflecting State Industries' confidence in the durability and longevity of their products.

One of the standout features of the SBD71120NE and SBD85500NE is their compatibility with smart home technology. Integrating these units with a smart thermostat enables users to monitor and manage their hot water usage remotely, thus contributing to more efficient energy consumption.

In conclusion, the State Industries SBD71120NE and SBD85500NE represent cutting-edge technologies and superior craftsmanship. Their respective sizes and capacities make them suitable options for a variety of applications, ensuring reliable hot water delivery while promoting energy efficiency and cost savings. With their advanced features and solid construction, these water heaters are designed to stand the test of time, providing homeowners and businesses with peace of mind and satisfaction.
Top Page Image Contents