State Industries SSED 5 Electrical Data, Branch Circuit, Heater Circuits, Control Circuits

Page 10

ELECTRICAL DATA

General

Check the water heater model and rating plate information against the characteristics of the branch circuit electrical supply. Do not connect the water heater to an improper source of electricity.

Voltage applied to the water heater should not vary more than +5% to -10% of the model and rating plate marking for satisfactory operation.

Do NOT energize the branch circuit for any reason before the water heater tank is filled with water. Doing so may cause the heating elements to fail.

The installation must conform to these instructions and the local code authority having jurisdiction. Grounding and electrical wiring connected to the water heater must also conform to the National Electrical Code, NFPA 70. This publication is available from The National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02269.

Branch Circuit

The branch circuit wire size should be established through reference to the NEC (National Electrical Code) or other locally approved sources in conjunction with the water heater amperage rating. Wire rated at 75°C should be used. For convenience, portions of the wire size tables from the Code are reproduced in Table 1 on page 11. It is suggested the electrician size the branch circuit at 125 percent of the water heater rating and further increase wire size as necessary to compensate for voltage drop in long runs. Voltage drop should not exceed 3% at the water heater.

Heater Circuits

The water heater’s electrical components are pictured and identified in the Features and Components illustrations in Figure 1 on page 6. The model and rating plate provides heater circuit ratings. There are two main electrical circuits:

Control Circuit: Power supply for the electromagnetic contactor coils. 120V power is supplied to the contactor coils by the CCB (Central Control Board) see wiring diagrams in this manual starting on page 12.

Power Circuit: High voltage, single or three phase, circuit that carries the heating element load.

The following section and pages describe the water heater circuits and includes wiring diagrams.

Control Circuits

The water heater is equipped with an electronic control system. The system includes a CCB (Central Control Board), an immersion temperature probe with ECO for temperature sensing and limiting, a UIM (User Interface Module) for user interface & information display and element current sensors for monitoring the power circuits. Refer to the control circuit label on the water heater for details. The CCB is powered by a small 120V/24V transformer. The control circuit operates on 120V supplied by a larger 100VA transformer.

Sequence of Operation

1.When the control is powered, the UIM should display model information, water temperature, operating setpoint, heating status and operating mode.

2.If the control determines that the actual water temperature inside the tank is below the programmed operating setpoint minus the

(1st) differential setpoint, a call for heat is activated.

3.After all safety checks are verified the CCB will energize the contactor coil(s). On models with more than one heating element the upper most heating elements are energized first. Successive heating elements are energized according to programmed differential setpoints for each heating element.

4.The control remains in the heating mode until the water temperature reaches the programmed operating setpoint. At this point the contactors will be de-energized.

5.The control system now enters the standby operating mode while continuing to monitor the water temperature and the state of other system devices. If the water temperature drops below the programmed Operating Setpoint minus the (1st) differential setpoint, the control will automatically return to step 2 and repeat the heating cycle.

Power Circuit

Power circuit wiring is type THHN (or equivalent) rated 600 volts, 105°C, sized as necessary.

The following wiring diagrams are included in this manual to show typical arrangements of electrical components in the control and power circuits by voltage and phase characteristics. They are to be used as a reference by the installer or servicer in performing their work. An actual diagram of the water heater wiring is furnished with the heater.

10

Page 9 Page 11
Image 10
Page 9 Page 11
Contents Installation Operation Service Maintenance Limited Warranty AsmeSafe INSTALLATION, USE and Service Qualified Installer or Service AgencyPrecautions Hydrogen GAS Flammable General Safety InformationGrounding Instructions Table of Contents IntroductionDimensions and Capacities Data SsedFeatures and Components Model and Rating Locating the NEW Water Heater ApprovalsFacts to Consider About the Location Required Ability Installation RequirementsTemperature-Pressure Relief Valve GeneralClosed Water Systems Water Line ConnectionsThermal Expansion Branch Circuit Power CircuitElectrical Data Heater CircuitsStandard KW Inputs 208-240V / 3PH Wiring DiagramsDiagram Small Commercial Wire Diagram 208-240V / 3-1PHPhase Conversions Diagram Small Commercial Wire Diagram Single PhaseDiagram 300-600V / 3PHInitial Start Up OperationFilling the Water Heater Draining the Water HeaterTemperature Adjustment Temperature RegulationHigh Temperature Limit Controls ECO Thermostat ControlsHeating Element Operation Control System FeaturesControl System Operation Control System NavigationStatus Icons Description Control System Menus Operating StatesMenus Description Temperatures Menu Temperature Settings ActionEconomy Mode Setup Menu Water Heater Status MenuDaily Operating Mode Sun Mon Tue Wed Thu Fri Sat Heater In Economy ModeCurrent Time Economy Mode Settings Setpoint Adjustment ValueTime Clock Settings Economy Mode All Day Daily Operating Mode SettingsNormal Operation Between Display Settings Menu Alarm Output Setup MenuWater Heater Information Menu Fault History Menu Current Fault / Alert MenuFault Occurrence Menu Restore Factory Defaults Menu Factory Defaults Restore Factory DefaultsMaintenance schedule MaintenanceTemperature-Pressure Relief Valve Operation FlushingProcess for Lime Scale Removal is AS Follows Lime Scale RemovalOther Scale Removal Troubleshooting Checklist Hard WaterWarranty TankPage Page Technical Support and Parts 800

SSED 5 specifications

State Industries, a prominent player in the heating and cooling sector, has unveiled its latest product, the SSED 5 series. This state-of-the-art water heater stands out in the market due to its unique features and advanced technologies designed to enhance efficiency, durability, and user-friendliness.

One of the key characteristics of the SSED 5 series is its innovative design. Constructed using high-quality materials, the unit is built to withstand the rigors of everyday usage while minimizing corrosion and wear. The external casing is both aesthetically pleasing and functional, providing adequate insulation to reduce heat loss, which in turn improves energy efficiency.

Energy-saving technologies are at the forefront of the SSED 5 series. It utilizes advanced heating elements that offer superior performance compared to traditional models. This includes a high thermal efficiency rating, allowing users to enjoy consistent hot water without incurring high utility bills. Moreover, the SSED 5 is equipped with integrated smart technology that enables users to monitor and control the unit remotely via a mobile app. This feature adds convenience and promotes energy conservation by allowing adjustments to be made according to real-time needs.

The SSED 5’s performance is further enhanced by its user-friendly digital control panel. This intuitive interface simplifies operation, allowing users to easily set their preferred water temperature and access diagnostic information. Safety features are also paramount, with built-in mechanisms to prevent overheating and leaks, ensuring peace of mind during operation.

Additionally, the SSED 5 series is notable for its environmental compliance. A commitment to sustainable practices is evident in its low emissions and energy-efficient operation, which contributes to reducing the overall carbon footprint.

In summary, the State Industries SSED 5 series represents a remarkable advancement in water heater technology. With its robust design, energy efficiency, smart technology integration, user-friendly interface, and safety features, it caters to modern consumers looking for reliable and effective heating solutions. As the demand for efficient and environmentally friendly products continues to rise, the SSED 5 is poised to meet and exceed market expectations. This makes it a leading choice for homeowners seeking innovation and quality in their hot water systems.
Top Page Image Contents