State Industries SSED 5 Operation, Filling the Water Heater, Initial Start Up, Energized

Page 15

OPERATION

General

Refer to the Features and Components section of this manual for the location of components mentioned in the instructions that follow.

NEVER operate the heating elements without being certain the water heater is filled with water, and a temperature and pressure relief valve is installed in the relief valve opening on top of the heater.

The pilot switch (power on/off toggle switch) on the cabinet front permits the heater to be turned on and off without having to operate the electrical disconnect switch.

Optional manual override switches on the cabinet front allow elements to be manually de-energized if full capacity is not needed.

Filling the Water Heater

To fill the water heater with water:

1.Turn off the electrical disconnect switch.

2.Turn off pilot toggle switch.

3.Close the heater drain valve.

4.Open a nearby hot water faucet to allow the air in the system to escape.

5.Fully open the cold water inlet valve, filling the heater and piping.

6.Close the hot water faucet when water starts to flow from the faucet. Leave the cold water inlet valve fully open. The heater is now ready for start up and temperature regulation.

7.Close the cabinet door and perform start up checks listed below before turning on the electricity.

INITIAL Start Up

The following checks should be made by the installer when the water heater is placed into operation for the first time:

1.Check all factory and field made water and electrical connections for tightness. Also check connections on top of the heater. Repair water leaks and tighten electrical connections as necessary.

2.Turn on the electrical disconnect switch and pilot toggle switch. The pilot toggle switch is located on cabinet.

3.Observe the operation of the electrical components during the first heating cycle. Use care as the electrical circuits are energized.

Temperature control and contactor operation should be checked by allowing heater to come up to temperature and shut off automatically. USE CARE AS THE ELECTRICAL CIRCUITS ARE

ENERGIZED.

Draining the Water Heater

To drain the water heater storage tank:

1.Turn off the electrical supply to the water heater at the circuit breaker or disconnect switch.

2.Turn off the pilot toggle switch on the water heater.

3.Ensure the cold water inlet valve is open.

4.Open a nearby hot water faucet and let the water run until the water is no longer hot.

5.Close the cold water inlet valve to the water heater.

6.Connect a hose to the water heater drain valve and terminate it to an adequate drain.

7.Open the water heater drain valve and allow all the water to drain from the storage tank.

8.Close the water heater drain valve when all water in the storage tank has drained.

9.Close the hot water faucet opened in Step 4.

10.If the water heater is going to be shut down for an extended period, the drain valve should be left open.

15

Page 14 Page 16
Image 15
Page 14 Page 16
Contents Asme Installation Operation Service Maintenance Limited WarrantyQualified Installer or Service Agency Safe INSTALLATION, USE and ServiceGeneral Safety Information Precautions Hydrogen GAS FlammableGrounding Instructions Introduction Table of ContentsSsed Dimensions and Capacities DataFeatures and Components Approvals Model and Rating Locating the NEW Water HeaterFacts to Consider About the Location General Installation RequirementsTemperature-Pressure Relief Valve Required AbilityWater Line Connections Closed Water SystemsThermal Expansion Heater Circuits Power CircuitElectrical Data Branch CircuitStandard KW Inputs 208-240V / 3-1PH Wiring DiagramsDiagram Small Commercial Wire Diagram 208-240V / 3PHDiagram Small Commercial Wire Diagram Single Phase Phase Conversions300-600V / 3PH DiagramDraining the Water Heater OperationFilling the Water Heater Initial Start UpThermostat Controls Temperature RegulationHigh Temperature Limit Controls ECO Temperature AdjustmentControl System Navigation Control System FeaturesControl System Operation Heating Element OperationStatus Icons Description Operating States Control System MenusMenus Description Temperatures Menu Action Temperature SettingsWater Heater Status Menu Economy Mode Setup MenuHeater In Economy Mode Daily Operating Mode Sun Mon Tue Wed Thu Fri SatCurrent Time Setpoint Adjustment Value Economy Mode SettingsTime Clock Settings Daily Operating Mode Settings Economy Mode All DayNormal Operation Between Alarm Output Setup Menu Display Settings MenuWater Heater Information Menu Current Fault / Alert Menu Fault History MenuFault Occurrence Menu Factory Defaults Restore Factory Defaults Restore Factory Defaults MenuFlushing MaintenanceTemperature-Pressure Relief Valve Operation Maintenance scheduleLime Scale Removal Process for Lime Scale Removal is AS FollowsOther Scale Removal Hard Water Troubleshooting ChecklistTank WarrantyPage Page Technical Support and Parts 800

SSED 5 specifications

State Industries, a prominent player in the heating and cooling sector, has unveiled its latest product, the SSED 5 series. This state-of-the-art water heater stands out in the market due to its unique features and advanced technologies designed to enhance efficiency, durability, and user-friendliness.

One of the key characteristics of the SSED 5 series is its innovative design. Constructed using high-quality materials, the unit is built to withstand the rigors of everyday usage while minimizing corrosion and wear. The external casing is both aesthetically pleasing and functional, providing adequate insulation to reduce heat loss, which in turn improves energy efficiency.

Energy-saving technologies are at the forefront of the SSED 5 series. It utilizes advanced heating elements that offer superior performance compared to traditional models. This includes a high thermal efficiency rating, allowing users to enjoy consistent hot water without incurring high utility bills. Moreover, the SSED 5 is equipped with integrated smart technology that enables users to monitor and control the unit remotely via a mobile app. This feature adds convenience and promotes energy conservation by allowing adjustments to be made according to real-time needs.

The SSED 5’s performance is further enhanced by its user-friendly digital control panel. This intuitive interface simplifies operation, allowing users to easily set their preferred water temperature and access diagnostic information. Safety features are also paramount, with built-in mechanisms to prevent overheating and leaks, ensuring peace of mind during operation.

Additionally, the SSED 5 series is notable for its environmental compliance. A commitment to sustainable practices is evident in its low emissions and energy-efficient operation, which contributes to reducing the overall carbon footprint.

In summary, the State Industries SSED 5 series represents a remarkable advancement in water heater technology. With its robust design, energy efficiency, smart technology integration, user-friendly interface, and safety features, it caters to modern consumers looking for reliable and effective heating solutions. As the demand for efficient and environmentally friendly products continues to rise, the SSED 5 is poised to meet and exceed market expectations. This makes it a leading choice for homeowners seeking innovation and quality in their hot water systems.
Top Page Image Contents