State Industries SSED 5 Installation Requirements, Required Ability, General, Contaminated Water

Page 8

INSTALLATION REQUIREMENTS

Required Ability

Installation and service of this water heater requires ability equivalent to that of a qualified agency (page 2) in the field involved.

Plumbing and electrical work is required.

General

The installation must conform with these instructions and the local code authority having jurisdiction and the requirements of the power company. In the absence of code requirements, follow NFPA-70 (current edition). In the absence of local codes, the installation must comply with the latest editions of the National Electrical Code, NFPA 70 or the Canadian Electrical Code CSA C22.1. The National Electrical Code may be ordered from: National Fire Protection Association, 1 Batterymarch Park, Quincy, MA 02269. The Canadian Electrical Code is available from the Canadian Standards Association, 8501 East Pleasant Valley Road, Cleveland, OH 44131.

Do NOT test electrical system before heater is filled with water, follow the START UP procedure in the OPERATION section of this manual.

The principal components of the heater are identified in the Features and Components illustration in Figure 1.

MIXING VALVE USAGE:

Water heaters are intended to produce hot water. Water heated to a temperature which will satisfy space heating, clothes washing, dish washing, cleaning and other sanitizing needs can scald and permanently injure you upon contact. Some people are more likely to be permanently injured by hot water than others. These include the elderly, children, the infirm, or physically/developmentally disabled. If anyone using hot water in your home fits into one of these groups or if there is a local code or state law requiring a maximum water temperature at the hot water tap, then you must take special precautions. In addition to using the lowest possible temperature setting that satisfies your hot water needs, a means such as a MIXING VALVE should be used at the hot water taps used by these people or at the water heater.

MIXING VALVES for reducing point of use temperature are available. Consult a qualified installer or service agency. Follow all manufacturer’s instructions for installation of these valves.

Before changing the factory setting on the thermostat, read the “Temperature Regulation” section in this manual.

CONTAMINATED WATER

Toxic chemicals, such as those used for boiler treatment shall not be introduced into this system.

Products of this sort should not be stored near the heater Also, air which is brought in contact with the water heater should not contain any of these chemicals. If necessary, uncontaminated air should be obtained from remote or outside sources.

Temperature-Pressure Relief Valve

Explosion Hazard

Temperature-Pressure Relief Valve must comply with ANSI Z21.22- CSA 4.4 and ASME code.

Properly sized Temperature-Relief Valve must be installed in opening provided.

Can result in overheating and excessive tank pressure.

Can cause serious injury or death.

This water heater is provided with a properly rated/sized and certified combination Temperature-Pressure Relief Valve (T&P valve) by the manufacturer. The T&P valve is certified by a nationally recognized testing laboratory that maintains periodic inspection of production of listed equipment of materials as meeting the requirements for Relief Valves for Hot Water Supply Systems, ANSI Z21.22 • CSA4.4, and the code requirements of ASME.

If replaced, the new T&P valve must meet the requirements of local codes, but not less than a combination Temperature- Pressure Relief Valve rated/sized and certified as indicated in the above paragraph. The new T&P valve must be marked with a maximum set pressure not to exceed the marked hydrostatic working pressure of the water heater (150 psi = 1,035 kPa) and a discharge capacity not less than the water heater Btu/hr or kW input rate as shown on the water heater’s model rating label.

NOTE: In addition to the factory installed Temperature-Pressure Relief Valve on the water heater, each remote storage tank that may be installed and piped to a water heating appliance must also have its own properly sized, rated and approved Temperature- Pressure Relief Valve installed. Call the toll free technical support phone number listed on the back cover of this manual for technical assistance in sizing a Temperature-Pressure Relief Valve for remote storage tanks.

8

Page 7 Page 9
Image 8
Page 7 Page 9
Contents Installation Operation Service Maintenance Limited Warranty AsmeSafe INSTALLATION, USE and Service Qualified Installer or Service AgencyGrounding Instructions General Safety InformationPrecautions Hydrogen GAS Flammable Table of Contents IntroductionDimensions and Capacities Data SsedFeatures and Components Facts to Consider About the Location ApprovalsModel and Rating Locating the NEW Water Heater Installation Requirements Temperature-Pressure Relief ValveRequired Ability GeneralThermal Expansion Water Line ConnectionsClosed Water Systems Power Circuit Electrical DataBranch Circuit Heater CircuitsStandard KW Inputs Wiring Diagrams Diagram Small Commercial Wire Diagram208-240V / 3PH 208-240V / 3-1PHPhase Conversions Diagram Small Commercial Wire Diagram Single PhaseDiagram 300-600V / 3PHOperation Filling the Water HeaterInitial Start Up Draining the Water HeaterTemperature Regulation High Temperature Limit Controls ECOTemperature Adjustment Thermostat ControlsControl System Features Control System OperationHeating Element Operation Control System NavigationStatus Icons Description Menus Description Operating StatesControl System Menus Temperatures Menu Temperature Settings ActionEconomy Mode Setup Menu Water Heater Status MenuCurrent Time Heater In Economy ModeDaily Operating Mode Sun Mon Tue Wed Thu Fri Sat Economy Mode Settings Setpoint Adjustment ValueTime Clock Settings Normal Operation Between Daily Operating Mode SettingsEconomy Mode All Day Water Heater Information Menu Alarm Output Setup MenuDisplay Settings Menu Fault Occurrence Menu Current Fault / Alert MenuFault History Menu Restore Factory Defaults Menu Factory Defaults Restore Factory DefaultsMaintenance Temperature-Pressure Relief Valve OperationMaintenance schedule FlushingOther Scale Removal Lime Scale RemovalProcess for Lime Scale Removal is AS Follows Troubleshooting Checklist Hard WaterWarranty TankPage Page Technical Support and Parts 800

SSED 5 specifications

State Industries, a prominent player in the heating and cooling sector, has unveiled its latest product, the SSED 5 series. This state-of-the-art water heater stands out in the market due to its unique features and advanced technologies designed to enhance efficiency, durability, and user-friendliness.

One of the key characteristics of the SSED 5 series is its innovative design. Constructed using high-quality materials, the unit is built to withstand the rigors of everyday usage while minimizing corrosion and wear. The external casing is both aesthetically pleasing and functional, providing adequate insulation to reduce heat loss, which in turn improves energy efficiency.

Energy-saving technologies are at the forefront of the SSED 5 series. It utilizes advanced heating elements that offer superior performance compared to traditional models. This includes a high thermal efficiency rating, allowing users to enjoy consistent hot water without incurring high utility bills. Moreover, the SSED 5 is equipped with integrated smart technology that enables users to monitor and control the unit remotely via a mobile app. This feature adds convenience and promotes energy conservation by allowing adjustments to be made according to real-time needs.

The SSED 5’s performance is further enhanced by its user-friendly digital control panel. This intuitive interface simplifies operation, allowing users to easily set their preferred water temperature and access diagnostic information. Safety features are also paramount, with built-in mechanisms to prevent overheating and leaks, ensuring peace of mind during operation.

Additionally, the SSED 5 series is notable for its environmental compliance. A commitment to sustainable practices is evident in its low emissions and energy-efficient operation, which contributes to reducing the overall carbon footprint.

In summary, the State Industries SSED 5 series represents a remarkable advancement in water heater technology. With its robust design, energy efficiency, smart technology integration, user-friendly interface, and safety features, it caters to modern consumers looking for reliable and effective heating solutions. As the demand for efficient and environmentally friendly products continues to rise, the SSED 5 is poised to meet and exceed market expectations. This makes it a leading choice for homeowners seeking innovation and quality in their hot water systems.
Top Page Image Contents