State Industries SSED 5 instruction manual Status Icons Description

Page 18

Status: The Operating State of the control system is displayed beneath the Operating Set Point.

FIGURE 5.

Menu: The left Operational Button is pressed to enter the Main Menu where all control system menus are accessed. See Table 3 for a list of control system menus.

Help: The right Operational Button is pressed to access instructions and explanations for user settings, Operating States, Status Icons, manufacturer’s web address, technical support phone number and service agent contact information.

Day/Time/Operating Mode: The current time and day are also displayed on the Desktop Screen. “Clock Not Set” will be displayed until the time clock has been initially set. Day and Time are adjusted in the Economy Mode Setup menu. The current Operating Mode, either Normal Mode or Economy Mode, is displayed beneath the day and time.

Discreet Menu Contact Information: From the Desktop Screen press and hold down the middle (unmarked) Operational Button for 30 seconds and then release it. This will launch a discreet menu where personalized contact information can be entered. Installing contractors and/or service agents can enter their company name and telephone number. This contact information will be displayed with all Fault and Alert messages.

TABLE 3 STATUS ICONS.

ICON

DESCRIPTION

Water temperature in the tank has fallen. Shaded area of the animated thermometer icon will rise and fall in response to water temperature in the storage tank as sensed from the immersion Temperature Probe.

Water temperature in the tank has reached the Operating Set Point. Shaded area of the animated thermometer icon will rise and fall in response to water temperature in the storage tank as sensed from the immersion Temperature Probe.

The control is unable to initiate a heating cycle. This will happen whenever a Fault condition is detected by the control system or when either of the two Enable/Disable circuits are open circuits.

The control system is in Heating Mode and has energized the electromagnetic contactor coils for at least one heating element. This animated icon DOES NOT indicate current has been sensed from the heating elements, only that there is a call for heat present and the control system has initiated heating element operation.

Heating element icon for a water heater equipped with 1 heating element. Open circles represent elements the control system has not energized and IS NOT sensing electrical current flow from.

Heating element icon for a water heater equipped with 2 heating elements. Each circle represents one element. Open circles represent elements the control system has not energized and IS NOT sensing electrical current flow from. Filled circles represent elements the control system has energized and IS sensing electrical current flow from.

Heating element icon for a water heater equipped with 3 heating elements. Each circle represents one element. Filled circles represent elements the control system has energized and IS sensing electrical current flow from.

Heating element icon for a water heater equipped with 4 heating elements. Each circle represents one element. Open circles with an X represent elements the control system has energized that it IS NOT sensing electrical current flow from.

Heating element icon for a water heater equipped with 5 heating elements. Each circle represents one element. Open circles represent elements the control system has not energized and IS NOT sensing electrical current flow from. Filled circles represent elements the control system has energized and IS sensing electrical current flow from.

The control has detected/declared a Fault Condition. Fault message details can be viewed in the Current Fault menu. Heating operation is discontinued (locked out) until the condition that caused the fault is corrected. Power to the water heater must be cycled off and on to reset the control system. Note; cycling power will not reset the control system if the condition that caused the fault has not been corrected.

The control has detected/declared an Alert Condition. The water heater will continue to operate during an Alert Condition but there is an operational condition that requires the attention of a Qualified Service Agent. Alert message details can be viewed in the Current Alert menu.

18

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Installation Operation Service Maintenance Limited Warranty AsmeSafe INSTALLATION, USE and Service Qualified Installer or Service AgencyGeneral Safety Information Precautions Hydrogen GAS FlammableGrounding Instructions Table of Contents IntroductionDimensions and Capacities Data SsedFeatures and Components Approvals Model and Rating Locating the NEW Water HeaterFacts to Consider About the Location Required Ability Installation RequirementsTemperature-Pressure Relief Valve GeneralWater Line Connections Closed Water SystemsThermal Expansion Branch Circuit Power CircuitElectrical Data Heater CircuitsStandard KW Inputs 208-240V / 3PH Wiring DiagramsDiagram Small Commercial Wire Diagram 208-240V / 3-1PHPhase Conversions Diagram Small Commercial Wire Diagram Single PhaseDiagram 300-600V / 3PHInitial Start Up OperationFilling the Water Heater Draining the Water HeaterTemperature Adjustment Temperature RegulationHigh Temperature Limit Controls ECO Thermostat ControlsHeating Element Operation Control System FeaturesControl System Operation Control System NavigationStatus Icons Description Operating States Control System MenusMenus Description Temperatures Menu Temperature Settings ActionEconomy Mode Setup Menu Water Heater Status MenuHeater In Economy Mode Daily Operating Mode Sun Mon Tue Wed Thu Fri SatCurrent Time Economy Mode Settings Setpoint Adjustment ValueTime Clock Settings Daily Operating Mode Settings Economy Mode All DayNormal Operation Between Alarm Output Setup Menu Display Settings MenuWater Heater Information Menu Current Fault / Alert Menu Fault History MenuFault Occurrence Menu Restore Factory Defaults Menu Factory Defaults Restore Factory DefaultsMaintenance schedule MaintenanceTemperature-Pressure Relief Valve Operation FlushingLime Scale Removal Process for Lime Scale Removal is AS FollowsOther Scale Removal Troubleshooting Checklist Hard WaterWarranty TankPage Page Technical Support and Parts 800

SSED 5 specifications

State Industries, a prominent player in the heating and cooling sector, has unveiled its latest product, the SSED 5 series. This state-of-the-art water heater stands out in the market due to its unique features and advanced technologies designed to enhance efficiency, durability, and user-friendliness.

One of the key characteristics of the SSED 5 series is its innovative design. Constructed using high-quality materials, the unit is built to withstand the rigors of everyday usage while minimizing corrosion and wear. The external casing is both aesthetically pleasing and functional, providing adequate insulation to reduce heat loss, which in turn improves energy efficiency.

Energy-saving technologies are at the forefront of the SSED 5 series. It utilizes advanced heating elements that offer superior performance compared to traditional models. This includes a high thermal efficiency rating, allowing users to enjoy consistent hot water without incurring high utility bills. Moreover, the SSED 5 is equipped with integrated smart technology that enables users to monitor and control the unit remotely via a mobile app. This feature adds convenience and promotes energy conservation by allowing adjustments to be made according to real-time needs.

The SSED 5’s performance is further enhanced by its user-friendly digital control panel. This intuitive interface simplifies operation, allowing users to easily set their preferred water temperature and access diagnostic information. Safety features are also paramount, with built-in mechanisms to prevent overheating and leaks, ensuring peace of mind during operation.

Additionally, the SSED 5 series is notable for its environmental compliance. A commitment to sustainable practices is evident in its low emissions and energy-efficient operation, which contributes to reducing the overall carbon footprint.

In summary, the State Industries SSED 5 series represents a remarkable advancement in water heater technology. With its robust design, energy efficiency, smart technology integration, user-friendly interface, and safety features, it caters to modern consumers looking for reliable and effective heating solutions. As the demand for efficient and environmentally friendly products continues to rise, the SSED 5 is poised to meet and exceed market expectations. This makes it a leading choice for homeowners seeking innovation and quality in their hot water systems.
Top Page Image Contents