State Industries SSED 5 Process for Lime Scale Removal is AS Follows, Other Scale Removal

Page 31

LIME SCALE REMOVAL

Lime scale accumulations on the heating elements is a normal condition, common to all immersion type elements. Factors which affect the amounts of this formation are:

1.Amount of hot water used. As the volume of the water heated increases, more scale results.

2.Water temperature. As the temperature of the water is increased, more scale is deposited on the elements.

3.Characteristics of water supply.

Regardless of water treatment, the elements should be examined regularly.

Lime scale accumulations may cause noises to occur during operation.

It is recommended that a heating element be removed periodically for examination. If it is scaled, all of the elements should be removed and cleaned. If the tank bottom has an accumulation of sediment it should be cleaned.

Lime scale should be removed by dissolving the accumulation in UN-LIME®delimer. Do not use muriatic or hydrochloric acid base deliming solutions to remove lime scale from the elements.

THE PROCESS FOR LIME SCALE REMOVAL IS AS FOLLOWS:

1.Turn off electrical disconnect switch.

2.Drain the heater following DRAINING instructions.

3.Open front panel.

4.Disconnect the element wiring. Try not to disturb the wiring unnecessarily and reconnection will be easier.

5.Unscrew each element.

6.Remove the elements and gaskets from the openings.

•Use a twisting, pulling action to remove elements scaled beyond the size of the tank openings.

•Brush loose scale from elements.

7.Lime scale removal:

•Place limed ends of heating elements into UN-LIME delimer and allow scale to dissolve. Do not permit delimer or water to contact heating element electrical terminals.

•Silicates, sulfates, and aluminates must be removed by scraping or other mechanical means. Lime scale dissolvents will not remove these types of scale which are occasionally encountered.

Call the toll free phone number on the back cover of this Instruction Manual to purchase UN-LIME and heating element gaskets.

OTHER SCALE REMOVAL:

1.Flush cleaned ends of elements with water when deliming or cleaning is completed.

2.Remove sediment and scale from the tank bottom through the access provided by the element openings or drain valve opening.

•The cold water inlet valve and drain valve may be opened to aid the cleanout process.

3.Clean remaining gasket material from tank and element flanges.

Do not reuse original element gaskets.

4.Put new gaskets on each element and install into tank openings.

•Uniformly tighten element bolts. Torque to approximately 32 ft/lbs.

5.Attach element wires to connection points from which they were removed.

6.Follow FILLING instructions on page 15 to restore hot water service.

•Check for water leaks around elements and proper operation when heater is filled.

•Close the panel.

31

Page 30 Page 32
Image 31
Page 30 Page 32
Contents Asme Installation Operation Service Maintenance Limited WarrantyQualified Installer or Service Agency Safe INSTALLATION, USE and ServicePrecautions Hydrogen GAS Flammable General Safety InformationGrounding Instructions Introduction Table of ContentsSsed Dimensions and Capacities DataFeatures and Components Model and Rating Locating the NEW Water Heater ApprovalsFacts to Consider About the Location General Installation RequirementsTemperature-Pressure Relief Valve Required AbilityClosed Water Systems Water Line ConnectionsThermal Expansion Heater Circuits Power CircuitElectrical Data Branch CircuitStandard KW Inputs 208-240V / 3-1PH Wiring DiagramsDiagram Small Commercial Wire Diagram 208-240V / 3PHDiagram Small Commercial Wire Diagram Single Phase Phase Conversions300-600V / 3PH DiagramDraining the Water Heater OperationFilling the Water Heater Initial Start UpThermostat Controls Temperature RegulationHigh Temperature Limit Controls ECO Temperature AdjustmentControl System Navigation Control System FeaturesControl System Operation Heating Element OperationStatus Icons Description Control System Menus Operating StatesMenus Description Temperatures Menu Action Temperature SettingsWater Heater Status Menu Economy Mode Setup MenuDaily Operating Mode Sun Mon Tue Wed Thu Fri Sat Heater In Economy ModeCurrent Time Setpoint Adjustment Value Economy Mode SettingsTime Clock Settings Economy Mode All Day Daily Operating Mode SettingsNormal Operation Between Display Settings Menu Alarm Output Setup MenuWater Heater Information Menu Fault History Menu Current Fault / Alert MenuFault Occurrence Menu Factory Defaults Restore Factory Defaults Restore Factory Defaults MenuFlushing MaintenanceTemperature-Pressure Relief Valve Operation Maintenance scheduleProcess for Lime Scale Removal is AS Follows Lime Scale RemovalOther Scale Removal Hard Water Troubleshooting ChecklistTank WarrantyPage Page Technical Support and Parts 800

SSED 5 specifications

State Industries, a prominent player in the heating and cooling sector, has unveiled its latest product, the SSED 5 series. This state-of-the-art water heater stands out in the market due to its unique features and advanced technologies designed to enhance efficiency, durability, and user-friendliness.

One of the key characteristics of the SSED 5 series is its innovative design. Constructed using high-quality materials, the unit is built to withstand the rigors of everyday usage while minimizing corrosion and wear. The external casing is both aesthetically pleasing and functional, providing adequate insulation to reduce heat loss, which in turn improves energy efficiency.

Energy-saving technologies are at the forefront of the SSED 5 series. It utilizes advanced heating elements that offer superior performance compared to traditional models. This includes a high thermal efficiency rating, allowing users to enjoy consistent hot water without incurring high utility bills. Moreover, the SSED 5 is equipped with integrated smart technology that enables users to monitor and control the unit remotely via a mobile app. This feature adds convenience and promotes energy conservation by allowing adjustments to be made according to real-time needs.

The SSED 5’s performance is further enhanced by its user-friendly digital control panel. This intuitive interface simplifies operation, allowing users to easily set their preferred water temperature and access diagnostic information. Safety features are also paramount, with built-in mechanisms to prevent overheating and leaks, ensuring peace of mind during operation.

Additionally, the SSED 5 series is notable for its environmental compliance. A commitment to sustainable practices is evident in its low emissions and energy-efficient operation, which contributes to reducing the overall carbon footprint.

In summary, the State Industries SSED 5 series represents a remarkable advancement in water heater technology. With its robust design, energy efficiency, smart technology integration, user-friendly interface, and safety features, it caters to modern consumers looking for reliable and effective heating solutions. As the demand for efficient and environmentally friendly products continues to rise, the SSED 5 is poised to meet and exceed market expectations. This makes it a leading choice for homeowners seeking innovation and quality in their hot water systems.
Top Page Image Contents