Pella installation instructions Pella Corporation Part Number 81DU0100, Wide, Paper

Page 1

© 2011 Pella Corporation

Part Number: 81DU0100

INSTALLATION INSTRUCTION -

NAIL FIN INSTALLATION BEFORE WEATHER BARRIER AND

FRAME SCREW OR CLIP INSTALLATION FOR REPLACEMENT

ALUMINUM-CLAD EXTERIOR HINGED PATIO DOORS (PELLA® PROLINE AND DESIGNER SERIES®)

ALUMINUM-CLAD EXTERIOR ENTRY DOORS (PELLA® AND ARCHITECT SERIES®)

Please read thoroughly and understand completely all the steps in this instruction prior to beginning installation.

Installation with Nail Fin

follow steps 1, 2, 3, 4, 6, 7

 

 

Replacement Installation Without Nail Fin

follow steps 1, 2, 3, 5, 6, 7

 

 

Instrucciones en español en el reverso.

These instructions were developed and tested for use with typical wood frame wall construction in a wall system designed to manage water. These instructions are not to be used with any other construction method. Installation instructions for use with other construction methods or multiple units may be obtained from Pella Corporation, a local Pella retailer or by visiting http://www.pella. com. Building designs, construction methods, building materials, and site conditions unique to your project may require an installation method different from these instructions and additional care. Determining the appropriate installation method is the responsibility of you, your architect or construction professional. Check with the individual (building owner, architect, contractor, installer and/or consumer) responsible for the project in addition to local building code officials to determine if these products comply with local codes.

REMEMBER TO USE APPROPRIATE PERSONAL PROTECTIVE EQUIPMENT.

 

 

Fin

Nailing Fin

9"

wide

Corner

 

 

 

 

 

 

Flashing

Paper

 

 

 

 

9"

 

F

 

l

 

a

9"

 

i

F

Side

Flashing

Tape

Top

Flashing

Tape

n

l

a

g

s

P

h

i

a

n

p

Astragal

Side

Flashing

Tape

e

g

r

P

 

 

a

 

p

 

e

 

r

Sill Support

Sill Flashing Tape #1

Sill Flashing Tape #2

Note: This instruction is intended for walls with or without sheathing. Illustrations show wall without sheathing.

Always read the Pella® Limited Warranty before purchasing or installing Pella

products. By installing this product, you are acknowledging that this Limited Warranty is part of the terms of the sale. Failure to comply with all Pella installation

and maintenance instructions may void your Pella product warranty. See Limited Warranty for complete details at http://warranty.pella.com.

Image 1
Contents Instrucciones en español en el reverso Pella Corporation Part Number 81DU0100Remember to USE Appropriate Personal Protective Equipment WideRough Opening Preparation Rough Opening Preparation For Doors Using Optional Sill PAN GO to StepGO to Step Apply sill flashing tape. Cut a Optional Sill Pan InstructionsCut two 9 pieces of flashing tape with a RIWKHWDSHDSSOLHGWRWKHVLGHŶDQJH7KH Prepare the Door for InstallationDQJOHRQWRWKHHWHULRU Designer Series Doors Setting and Fastening the DoorFor doors with no lock/bore Clip or Frame Screw Installation, go to Step Setting and Fastening the Door3ED Check door operation. Open and close the door to check for Double Doors OnlyDoor Frame Corner Integrating the Door to the Water Resistive BarrierHead Flashing Instruction and Rough Opening Preparation Door Replacement in Siding Without Nail FINApply top flashing tape. Cut a piece of flashing Apply the top flashing paper. Cut one piece0DNHVXUHWKHWDSHLVDSSOLHG Door Replacement in Siding Without Nail FINOut-Swing Screw Locations In-Swing Screw Locations KROHVFUHZVLH ORFDWLRQGHWDLOVSee C for Clip Application Details Installation Clip MethodFasten the door to the opening by driving Check the door operation by opening and closing the door Interior Seal6AB 6CA Sealing the Door to the Exterior Wall Cladding Replacement FrameExterior Wall Cladding Sealing the Door toInsert backer rod into the space around HWHULRUIDFHRIWKHGRRUFinishing Instructions Interior FinishingExterior Finishing Care and Maintenance Important NoticeIssue Troubleshooting Adjustable Strike Latching Issues