Pella 81DU0100 Double Doors Only, Check door operation. Open and close the door to check for

3SETTING AND FASTENING THE DOOR (continued):

K.Double Doors Only:

Designer Series®: Place a dab of sealant into the center sill VWULNHKROHDQGLQVWDOOWKH[ŶDWKHDGFRUURVLRQUHVLVWDQW VFUHZVSURYLGHGRUDPDVRQU\VFUHZVLQWRWKHKROH

ProLine®: Remove the screw from the sill strike located on the door sill, then place a dab of sealant into the sill strike KROHDQGLQVWDOOWKH[ŶDWKHDGFRUURVLRQUHVLVWDQWVFUHZ SURYLGHGRUDPDVRQU\VFUHZLQWRWKHKROH

Entry Doors: Remove the two screws from the sill strike located on the door sill. Place a dab of sealant into the FHQWHUVLOOVWULNHKROHDQGLQVWDOOWKH[ŶDWKHDG FRUURVLRQUHVLVWDQWVFUHZVSURYLGHGRUDPDVRQU\ screws into the hole.

Interior

3L3K

3J

3K

L.Double Doors Only: Shim between the frame and the rough opening at the head strike

ORFDWLRQDQGDWHYHU\IUDPHDQFKRUKROHORFDWLRQ.HHSVKLPVEDFNIURPLQWHULRUIDFHRI the door frame.

Designer Series:,QVWDOOWKH[ŶDWKHDGFRUURVLRQUHVLVWDQWVFUHZVSURYLGHGLQWRWKH hole.

ProLine:5HPRYHWKHVFUHZIURPWKHKHDGVWULNHORFDWHGRQWKHGRRUKHDGWKHQLQVWDOOWKH [ŶDWKHDGFRUURVLRQUHVLVWDQWVFUHZVSURYLGHGLQWRWKHKROH

Entry Doors: Remove the two screws from the head strike located on the door head. Install

WKH[ŶDWKHDGFRUURVLRQUHVLVWDQWVFUHZVSURYLGHGLQWRWKHKROH

Note: For doors with pre-drilled installation holes in the head. If installation holes are present, drill 1/8" diameter pilot hole into the rough opening and install a #8 x 3" corrosion resistant screw (provided) in each hole.

0 2QHDFKKLQJHVWDUWLQJDWWKHWRSLQVHUWDFRUURVLRQUHVLVWDQW VFUHZ[SURYLGHGLQWRWKHRSHQVFUHZKROH0DNHVXUH the screw passes through the shims and into the structural framing.

N.Check door operation. Open and close the door to check for

SURSHURSHUDWLRQ0DNHVXUHWKHGRRUZLOOODWFKFRUUHFWO\

Note: If there are any problems with the operation, check to confirm the door frame is installed plumb, level and square. If the reveal between the door panel(s) and frame is not even, adjustments may be made:

Interior

3M3L

Doors without adjustable hinges: Plastic shims located behind the hinges may be removed to adjust the reveal between the door panel and door frame. Additional hinge shims may be added if required.

Note: Doors with adjustable hinges will have a (+)(-) on the door panel hinge leaf to indicate possible adjustments and doors without adjustable hinges do not have adjustment indicators.

Adjustable hinges are not designed to make up for incorrect installation of a door frame. Before adjusting hinges, confirm the door is installed plumb, level and square.

Adjustable

Hinge

Non-Adjustable

Hinge

O.For Doors with adjustable hinges: The hinges can be used to move the panel side to side by moving all hinges in the same direction or the hinges can slightly rotate the panel by

DGMXVWLQJWKHKLQJHVLQRSSRVLWHGLUHFWLRQV8VHD77RU[ZUHQFKIRU(QWU\'RRUVRUD

Allen wrench for Designer Series doors to turn the center screw clockwise (+) to increase the space between the hinge side of the frame and door panel. Turn the center screws counter- clockwise (-) to decrease the space between the hinge side of the frame and the door panel

.

Note: Do not adjust the hinge with the top and bottom screws loose; this could force the hinge to adjust beyond its design capability which can cause the hinge to bind, damage the hinge and/or pull out the screws. A 3/4 turn of the center screw provides approximately 5/32" adjustment.