Pella 81DU0100 installation instructions Rough Opening Preparation

Page 2

The performance of any building is dependent upon the design, installation, and workmanship

RIWKHHQWLUHEXLOGLQJV\VWHP3HOOD&RUSRUDWLRQVWURQJO\UHFRPPHQGVFRQVXOWLQJDQH[SHULHQFHG architect, contractor or structural engineer prior to installation of Pella products.

The individual (building owner, architect, contractor, installer and/or consumer) responsible for the project must take into account local conditions, building codes, inherent component limitations, the effects of aging and weathering on building components, and other design issues relevant to each project.

The determination of the suitability of all building components for each project, as well as the design and installation of ﬂashing and sealing systems, are the responsibility of the building owner, architect, contractor, installer and/or consumer.

YOU WILL NEED TO SUPPLY:

Ř&RPSRVLWHRU,PSHUYLRXVVKLPVVSDFHUVWR
ŘJDOYDQL]HGURRILQJQDLOVOE
Ř[FRUURVLRQUHVLVWDQWZRRGVFUHZV
(Performance Upgrade & HurricaneShield)
Ř0DVRQU\VFUHZVIRUFRQFUHWHDSSOLFDWLRQV
0LQLPXPRIőGLDPHWHU[
Ř&ORVHGFHOOIRDPEDFNHUURGVHDODQWEDFNHU
WRIW
Ř3HOOD® SmartFlash™ foil backed butyl window and
door flashing tape or equivalent
Ř+LJKTXDOLW\H[WHULRUJUDGHSRO\XUHWKDQHRUVLOLFRQH
VHDODQWWRWXEHVSHUGRRU	4&"-"/5
VHDODQWWRWXEHVSHUGRRU

Ř*UHDW6WXII™ Window and Door Insulating Foam Sealant by the Dow Chemical Company or equiva- lent low pressure polyurethane window and door IRDP'2127XVHKLJKSUHVVXUHRUODWH[IRDPV

Ř6LOOSDQRSWLRQDO

Ř3HOODDOXPLQXPVLOOVXSSRUWRUZRRGEORFNLQJ

Ř,QWHULRUWULPDQGRUMDPEH[WHQVLRQVWRIW

Installation Clip Option:

ŘRULQVWDOODWLRQFOLSV

Ř[FRUURVLRQUHVLVWDQWIODWKHDGZRRGVFUHZV Ř[FRUURVLRQUHVLVWDQWVFUHZVRU[

PDVRQU\VFUHZV

TOOLS REQUIRED:

Ř7DSHPHDVXUH

Ř/HYHO Ř6TXDUH Ř+DPPHU Ř6WDSOHU Ř6HDODQW*XQ Ř6FLVVRUVRUXWLOLW\NQLIH Ř7LQ6QLSV Ř6FUHZGULYHUV

3KLOOLSVZLWKVKDIW and small flat blade)

Ř77RU[:UHQFK (Architect Series®)

Ř$OOHQZUHQFK (Designer Series®)

Ř'ULOO Ř'ULOO%LWVDQG

DQGPDVRQU\ELWIRU concrete applications

1ROUGH OPENING PREPARATION:

A.Conﬁrm the opening is plumb and level. Note: It is critical the bottom is level.

"

Image 2

Contents Remember to USE Appropriate Personal Protective Equipment Pella Corporation Part Number 81DU0100Instrucciones en español en el reverso WideRough Opening Preparation GO to Step For Doors Using Optional Sill PAN GO to StepRough Opening Preparation Cut two 9 pieces of ﬂashing tape with a Optional Sill Pan InstructionsApply sill ﬂashing tape. Cut a DQJOHRQWRWKHHWHULRU Prepare the Door for InstallationRIWKHWDSHDSSOLHGWRWKHVLGHŶDQJH7KH For doors with no lock/bore Setting and Fastening the DoorDesigner Series Doors 3ED Setting and Fastening the DoorClip or Frame Screw Installation, go to Step Double Doors Only Check door operation. Open and close the door to check forIntegrating the Door to the Water Resistive Barrier Door Frame CornerApply top ﬂashing tape. Cut a piece of ﬂashing Door Replacement in Siding Without Nail FINHead Flashing Instruction and Rough Opening Preparation Apply the top ﬂashing paper. Cut one pieceDoor Replacement in Siding Without Nail FIN 0DNHVXUHWKHWDSHLVDSSOLHGKROHVFUHZVLH ORFDWLRQGHWDLOV Out-Swing Screw Locations In-Swing Screw LocationsFasten the door to the opening by driving Installation Clip MethodSee C for Clip Application Details 6AB 6CA Interior SealCheck the door operation by opening and closing the door Replacement Frame Sealing the Door to the Exterior Wall CladdingInsert backer rod into the space around Sealing the Door toExterior Wall Cladding HWHULRUIDFHRIWKHGRRUInterior Finishing Finishing InstructionsCare and Maintenance Important Notice Exterior FinishingTroubleshooting Adjustable Strike Latching Issues Issue