Pella 81DU0100 installation instructions Exterior Finishing, Care and Maintenance Important Notice

Page 18

EXTERIOR FINISHING

7KHH[WHULRUIUDPHDQGVDVKDUHSURWHFWHGE\DOXPLQXPFODGGLQJZLWKD3HOOD(QGXUD&ODGpRU EnduraClad Plus baked-on factory finish that needs no painting. Clean this surface with mild soap and water. Stubborn stains and deposits may be removed with mineral spirits. DO NOT use abrasives. DO NOT scrape or use tools that might damage the surface.

Use of inappropriate finishes, solvents, brickwash or cleaning chemicals will cause adverse reactions with window and door materials and voids the Limited Warranty.

CARE AND MAINTENANCE

&DUHDQGPDLQWHQDQFHLQIRUPDWLRQLVDYDLODEOHLQWKH3HOOD2ZQHUőV0DQXDO<RXFDQREWDLQDQ RZQHUőVPDQXDOE\FRQWDFWLQJ\RXUORFDO3HOODUHWDLOHU7KLVLQIRUPDWLRQLVDOVRDYDLODEOHDW www.pella.com.

IMPORTANT NOTICE

Because all construction must anticipate some water infiltration, it is important that the wall system be designed and constructed to properly manage moisture. Pella Corporation is not responsible for claims or damages caused by anticipated and unanticipated water infiltration; deficiencies in building design, construction and maintenance; failure to install Pella® products in accordance with Pella installation instructions; or the use of Pella products in wall systems which do not allow for proper management of moisture within the wall systems. The determination of the suitability of all building components, including the use of Pella products, as well as the design and installation of flashing and sealing systems are the responsibility of the Buyer or User, the architect, contractor, installer, or other construction professional and are not the responsibility of Pella.

Pella products should not be used in barrier wall systems which do not allow for proper PDQDJHPHQWRIPRLVWXUHZLWKLQWKHZDOOV\VWHPVVXFKDVEDUULHU([WHULRU,QVXODWLRQDQG)LQLVK 6\VWHPV (,)6  DOVRNQRZQDVV\QWKHWLFVWXFFR RURWKHUQRQZDWHUPDQDJHGV\VWHPV([FHSWLQWKH VWDWHVRI&DOLIRUQLD1HZ0H[LFR$UL]RQD1HYDGD8WDKDQG&RORUDGRPella makes no warranty of any kind and assumes no responsibility for Pella windows and doors installed in barrier wall systems. In the states listed above, the installation of Pella products in barrier wall or similar systems must be in accordance with Pella installation instructions.

Product modifications that are not approved by Pella Corporation will void the Limited Warranty.

Page 17 Page 19
Image 18
Page 17 Page 19
Contents Remember to USE Appropriate Personal Protective Equipment Pella Corporation Part Number 81DU0100Instrucciones en español en el reverso WideRough Opening Preparation For Doors Using Optional Sill PAN GO to Step Rough Opening PreparationGO to Step Optional Sill Pan Instructions Apply sill flashing tape. Cut aCut two 9 pieces of flashing tape with a Prepare the Door for Installation RIWKHWDSHDSSOLHGWRWKHVLGHŶDQJH7KHDQJOHRQWRWKHHWHULRU Setting and Fastening the Door Designer Series DoorsFor doors with no lock/bore Setting and Fastening the Door Clip or Frame Screw Installation, go to Step3ED Double Doors Only Check door operation. Open and close the door to check forIntegrating the Door to the Water Resistive Barrier Door Frame CornerApply top flashing tape. Cut a piece of flashing Door Replacement in Siding Without Nail FINHead Flashing Instruction and Rough Opening Preparation Apply the top flashing paper. Cut one pieceDoor Replacement in Siding Without Nail FIN 0DNHVXUHWKHWDSHLVDSSOLHGKROHVFUHZVLH ORFDWLRQGHWDLOV Out-Swing Screw Locations In-Swing Screw LocationsInstallation Clip Method See C for Clip Application DetailsFasten the door to the opening by driving Interior Seal Check the door operation by opening and closing the door6AB 6CA Replacement Frame Sealing the Door to the Exterior Wall CladdingInsert backer rod into the space around Sealing the Door toExterior Wall Cladding HWHULRUIDFHRIWKHGRRUInterior Finishing Finishing InstructionsCare and Maintenance Important Notice Exterior FinishingTroubleshooting Adjustable Strike Latching Issues Issue
Top Page Image Contents