Pella 81DU0100 Installation Clip Method, See C for Clip Application Details

Page 13

5DOOR REPLACEMENT IN SIDING WITHOUT NAIL FIN (continued):

Frame Screw Method:

Note: If installing with installation clips, proceed to step P.

J.Jambs'ULOODQGFRXQWHUVLQNGLDPHWHUFOHDUDQFHKROHVWKURXJKWKHGRRUIUDPHRQO\ and not into the rough opening at the locations shown on the diagrams.

Note: Out-Swing Doors Only - If choosing to locate clearance holes through the frame to be concealed by door panel; remove frame weatherstrip and drill holes under the weatherstrip.

5J

K.Frame Head'ULOODQGFRXQWHUVLQNGLDPHWHUFOHDUDQFHKROHVWKURXJKWKHGRRU frame head only and not into the rough opening at the locations shown on the diagrams.

L.Threshold'ULOODQGFRXQWHUVLQNGLDPHWHUFOHDUDQFHKROHVWKURXJKWKHWKUHVKROG but not into the rough opening at the locations shown on the diagrams

0 Drill 1/8" x 1" deep pilot holes through the clearance holes and into the rough opening framing in the head, jambs and threshold of the unit frame.

N.Secure the jambs and head of the door.'ULYH[FRUURVLRQUHVLVWDQWZRRG screws through the door frame and shim, into the rough framing. Drive the screws until snug but DO NOT over-tighten the screws. DO NOT bend or bow the unit frame.

O.Secure the sillE\GULYLQJ[FRUURVLRQUHVLVWDQWZRRGVFUHZWKURXJKWKH WKUHVKROGLQWRWKHŶRRU)RUPDVRQU\DSSOLFDWLRQVXVHPDVRQU\VFUHZVDPLQLPXPRI GLDPHWHU[DQGSLORWGULOOSHUVFUHZPDQXIDFWXUHUőVUHFRPPHQGDWLRQV

Go back to 3H - 3P to complete fastening through hinges and strikes.

Installation Clip Method:

See Step 2C for Clip Application Details

P.Fasten the door to the opening by driving

WZR[FRUURVLRQUHVLVWDQWVFUHZV into the pre-punched holes in the clips.

If the clips are bent and fastened to the

interior stud/block, install the screws as 5PF close to the bend as possible.

Note: DO NOT shim above the door. For masonry openings use two masonry screws that are a minimum size of 3/16" x 1-1/2" per clip. Pre-drill the masonry per screw manufacturer’s recommendations before attempting to drive the screws in.

Go back to 3H - 3P to complete fastening through hinges and strikes.

Page 12 Page 14
Image 13
Page 12 Page 14
Contents Instrucciones en español en el reverso Pella Corporation Part Number 81DU0100Remember to USE Appropriate Personal Protective Equipment WideRough Opening Preparation Rough Opening Preparation For Doors Using Optional Sill PAN GO to StepGO to Step Apply sill flashing tape. Cut a Optional Sill Pan InstructionsCut two 9 pieces of flashing tape with a RIWKHWDSHDSSOLHGWRWKHVLGHŶDQJH7KH Prepare the Door for InstallationDQJOHRQWRWKHHWHULRU Designer Series Doors Setting and Fastening the DoorFor doors with no lock/bore Clip or Frame Screw Installation, go to Step Setting and Fastening the Door3ED Check door operation. Open and close the door to check for Double Doors OnlyDoor Frame Corner Integrating the Door to the Water Resistive BarrierHead Flashing Instruction and Rough Opening Preparation Door Replacement in Siding Without Nail FINApply top flashing tape. Cut a piece of flashing Apply the top flashing paper. Cut one piece0DNHVXUHWKHWDSHLVDSSOLHG Door Replacement in Siding Without Nail FINOut-Swing Screw Locations In-Swing Screw Locations KROHVFUHZVLH ORFDWLRQGHWDLOVSee C for Clip Application Details Installation Clip MethodFasten the door to the opening by driving Check the door operation by opening and closing the door Interior Seal6AB 6CA Sealing the Door to the Exterior Wall Cladding Replacement FrameExterior Wall Cladding Sealing the Door toInsert backer rod into the space around HWHULRUIDFHRIWKHGRRUFinishing Instructions Interior FinishingExterior Finishing Care and Maintenance Important NoticeIssue Troubleshooting Adjustable Strike Latching Issues
Top Page Image Contents