England's Stove Works 40-TRCPM Replacing the Stirrer Drive Motor, Removing Motor and Sprocket

Page 22

As with any maintenance concerning this unit, be sure the unit is “OFF” and has completed the Shut- Down cycle BEFORE beginning. Be aware that metal parts in the firebox can remain HOT long after the fire has gone out and EVEN after the Shut-Down cycle is complete. Always use extreme caution when handling potentially hot stove parts, even if you think they should be cold.

Replacing the Stirrer Drive Motor

1.Locate the access panel on the right side of stove (looking from front of stove).

2.Remove the four (4) 5/16“ mounting screws.

3.Locate the drive motor mounting bracket which is secured by two (2) 1/2“ bolts (C). Loosen these bolts.

4.Locate the 1/2“ chain adjustment bolt (A) on the left side of the drive motor. Loosen this bolt.

5.Remove the two (2) 1/2“ mounting bolts (C).

6.Slide drive motor mounting bracket toward the front of the stove and remove chain from sprocket

(B).

7.Remove bracket and motor through access panel and disconnect the two power leads from motor.

Removing Motor and Sprocket

1.Remove 1/2“ chain adjustment bolt (A).

2.Locate the 3/32“ Allen Head setscrew on the sprocket and loosen.

3.Remove sprocket (B) from motor shaft.

4.Remove the four (4) drive motor mounting screws (D) with a 5/16“ nutdriver or socket.

NOTE: When re-installing the sprocket, align the 3/32“ Allen Head setscrew with the flat side of the motor shaft.

Replacing the Stirrer Drive Shaft

1.Remove cast plug from right side (looking from the front of the stove) using a 3/16“ Allen Wrench.

2.Locate the access panel on the right side (looking from front of stove).

3.Remove the four (4) 5/16“ mounting screws (D).

4.Locate the drive motor mounting bracket which is secured by two (2) 1/2“ bolts (C). Loosen these bolts.

5.Locate the 1/2“ chain adjustment bolt (A) on the left side of the drive motor. Loosen this bolt.

6.Remove chain from Stirrer Shaft sprocket (B).

NOTE: It may be necessary to rotate the shaft by hand to access the set screw.

7.Locate the 3/32“ Allen Head setscrew on the sprocket and loosen.

8.Remove 5/8“ locking collar from Stirrer shaft inside the unit using a 5/32“ Allen Wrench.

9.Remove shaft by pulling to you from outside the stove.

(D) 5/16" Motor mounting screws

(B) Sprockets

(A) 1/2" Chain adjustment

bolt

(C) 1/2" Mounting bracket bolts

Illustration 5 - Motor, Shaft and Sprockets

22

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

Page 21 Page 23
Image 22
Page 21 Page 23
Contents Model Numbers 10-CPM 49-TRCPM 49-SHCPM Must be maintainedLetter from our Technical Support department England’s Stove Works Technical Support Department 800Important Information Important Notice Unit Preparation Important Information Read Before OperatingPage Page Do not Connect to ANY AIR Distribution Duct or System Shelled Corn Burning Solid FuelsWood Pellets Cherry PitsFlue System Through the WallThrough the Ceiling Mobile Home InstallationOutside Air Outside Combustion Air Intake Floor Protection Freestanding Pellet/Corn/Multi-fuel InstallationFloor and Wall Protection Wall ProtectionOperating Instructions START- UP ProceduresSetting the Stirrer Bodily Injury can occurFuel not Feeding Correctly To remove the Stirrer for cleaning Changing from Pellets to Corn Fuel Change ProcedureChanging from Pellets to Cherry Pits Codes Operational NotesTechnical Support Department SHUT-DOWN Procedure From the Power SourceBox Parts Orders only Monroe, VA Questions Fax Daily Operation ASH Removal and Disposal Maintenance Semi-Weekly Ash MaintenanceAnnual Maintenance Ash PanMaintenance Removing Motor and Sprocket Replacing the Stirrer Drive MotorReplacing the Stirrer Drive Shaft Finish GasketsGlass Control Board Recommended Heat RangesCircuit Board Functions Component Operation Start Operation ENDThermostat Accessory ItemsAccessories and Options AC-109, AC-109BN Lip TrimReplacement Parts CPM-APSee Item numbers on Exploded Diagram for part location Adjusting your Hopper Lid Latch Solution Problem CauseImproper installation may cause a back draft Problem Cause Solution Page Warranty is not Transferable Page Warranty Registration for England’s Stove Works Unit Information

40-TRCPM, 10-CPM, 49-SCHPM specifications

England's Stove Works is renowned for its commitment to crafting high-quality wood stoves and pellet stoves, and three of their notable products are the 49-SCHPM, 10-CPM, and 40-TRCPM models. Each of these stoves embodies the brand's dedication to efficiency, durability, and performance, making them popular choices for both heating homes and providing a cozy ambiance.

The 49-SCHPM is a powerful pellet stove designed to heat large spaces. It features a spacious hopper that can hold up to 60 pounds of pellets, allowing for extended burn times of up to 80 hours on lower settings. The stove incorporates an easy-to-use digital control board and a built-in thermostat, providing users with precise temperature regulation. This model also boasts a sleek, contemporary design, making it suitable for modern homes while still delivering traditional warmth.

In contrast, the 10-CPM is a compact and efficient pellet stove, ideal for smaller homes or tight spaces. Despite its smaller footprint, it still offers impressive heating capabilities with up to 35,000 BTU output, making it a formidable option for anyone seeking an efficient heat source without sacrificing performance. The 10-CPM features a large viewing window, which enhances the aesthetic appeal and allows users to enjoy the mesmerizing flames. It is also equipped with an automatic ignition system, making it convenient and easy to start.

The 40-TRCPM model showcases England's Stove Works' dedication to versatility. This multi-fuel stove can efficiently burn both wood pellets and corn, allowing homeowners the flexibility to choose their fuel source based on availability and cost. With an output capacity of 40,000 BTU, it is built to dominate larger areas while maintaining a steady heat output. The unit features a sophisticated combustion system that maximizes fuel efficiency and minimizes emissions, aligning with environmentally sustainable practices.

All three models utilize advanced engineering and technology to ensure an optimal burning experience. They come equipped with efficient air circulation systems and adjustable airflow to promote complete combustion, which results in less smoke and creosote buildup. This not only enhances safety but also contributes to the longevity of each unit.

Overall, England's Stove Works has established a strong reputation for producing reliable, efficient, and aesthetically pleasing stoves. The 49-SCHPM, 10-CPM, and 40-TRCPM exemplify the brand's commitment to quality and innovation, making them solid choices for anyone looking to enhance their home's heating system.
Top Page Image Contents