England's Stove Works 10-CPM, 40-TRCPM, 49-SCHPM operation manual Important Information

Page 3

IMPORTANT INFORMATION

1.Installation of this Pellet/Corn/Multi-fuel unit should be performed by a professional only. Check local installation codes for your area. Call your Homeowner’s Insurance representative for inspection of your stove’s installation.

2.Read and comply with the instructions in this manual.

3.This unit should be tested (dry run) for 20 minutes before loading pellets or cherry pits. The stove should automatically shut itself off after the 20-minute dry run. Corn is a 30-minute cycle.

4.If burning pellets, you should use Premium Pellets, as this stove is designed for Premium Pellets. Pellets with high ash content will burn dirty and require the unit to be cleaned more often.

5.If burning corn, you should use corn with less than 14% moisture content. Corn with high moisture content will burn dirty and require the unit to be cleaned more often.

6.If burning cherry pits, you should use cherry pits with less than 4% moisture content. Cherry pits with high moisture content will burn dirty and require the unit to be cleaned more often.

7.Be sure your corn, cherry pits or pellets are not damp or wet. If your fuel is too damp, this stove may not be able to run on the lower Heat Range settings (the fire will die out). Be sure to keep sawdust, debris and fines out of the unit.

8.Use three-inch (3”) U.L.-approved CORN VENT TWIST-LOCK PIPE when installing this stove and follow the manufacturer’s specifications for installation and clearances (we highly recommend Dura-Vent corn twist-lock pipe – our Part Number AC-33000). Even though this pipe interlocks, it is recommended to seal all connections with high temperature silicone (our Part Number AC-RTV3) or aluminum duct seal tape. Use at least three screws to secure the pipe to this unit’s exhaust blower. Also, if you do not use U.L.- approved twist-lock corn pipe, be sure to use U.L.-approved Corn Vent pipe, and fasten each joint of the pipe with at least three screws.

9.Outside combustion air is mandatory for these units to work properly. Make this connection using a 1 7/8” I.D. metal pipe (steel, aluminum or copper) and coupler. Be sure to secure the pipe to the unit with a clamp or aluminum tape. The outside end should be covered (screened) to prevent any foreign matter from entering the system. Try to keep the number of bends in this pipe to a minimum. Our Part Number PU-OAK(Outside Air Kit with flex pipe) can be used.

NOTE: If the total run of the connection exceeds six feet (6’), use 3” metal pipe and coupler instead.

10.Regularly inspect the burnpot area, remove the feeder pot and clean all plugged holes. See Maintenance Section.

11.The ash in the burnpot should be removed regularly, depending on your burn rate. The area to the right and left of the burnpot is for ash storage; keep the air holes in the burnpot clean for a more efficient burn. Check your exhaust system frequently. Refer to “Ash Removal and Disposal” section.

3

IMPORTANT! READ AND FOLLOW ALL INSTALLATION AND MAINTENANCE INSTRUCTIONS, INCLUDING

CLEANING THE UNIT AS SPECIFIED, AND REPLACING GASKETS ANNUALLY, AND PARTS AS NEEDED.

ENGLAND’S STOVE WORKS IS NOT RESPONSIBLE FOR ANY DAMAGE OR INJURY INCURRED DUE TO NEGLECT, OR DUE

TO UNSAFE INSTALLATION OR USAGE OF THIS PRODUCT. CALL TECHNICAL SUPPORT WITH QUESTIONS.

Image 3
Contents Must be maintained Model Numbers 10-CPM 49-TRCPM 49-SHCPMEngland’s Stove Works Technical Support Department 800 Letter from our Technical Support departmentImportant Information Important Notice Important Information Read Before Operating Unit PreparationPage Page Do not Connect to ANY AIR Distribution Duct or System Cherry Pits Burning Solid FuelsWood Pellets Shelled CornThrough the Wall Flue SystemMobile Home Installation Through the CeilingOutside Air Outside Combustion Air Intake Wall Protection Freestanding Pellet/Corn/Multi-fuel InstallationFloor and Wall Protection Floor ProtectionBodily Injury can occur START- UP ProceduresSetting the Stirrer Operating InstructionsFuel not Feeding Correctly To remove the Stirrer for cleaning Fuel Change Procedure Changing from Pellets to CornChanging from Pellets to Cherry Pits Operational Notes CodesSHUT-DOWN Procedure From the Power Source Technical Support DepartmentBox Parts Orders only Monroe, VA Questions Fax Daily Operation Ash Pan Maintenance Semi-Weekly Ash MaintenanceAnnual Maintenance ASH Removal and DisposalMaintenance Replacing the Stirrer Drive Motor Removing Motor and SprocketReplacing the Stirrer Drive Shaft Gaskets FinishGlass Recommended Heat Ranges Control BoardComponent Operation Start Operation END Circuit Board FunctionsAC-109, AC-109BN Lip Trim Accessory ItemsAccessories and Options ThermostatCPM-AP Replacement PartsSee Item numbers on Exploded Diagram for part location Adjusting your Hopper Lid Latch Problem Cause SolutionImproper installation may cause a back draft Problem Cause Solution Page Warranty is not Transferable Page Unit Information Warranty Registration for England’s Stove Works

40-TRCPM, 10-CPM, 49-SCHPM specifications

England's Stove Works is renowned for its commitment to crafting high-quality wood stoves and pellet stoves, and three of their notable products are the 49-SCHPM, 10-CPM, and 40-TRCPM models. Each of these stoves embodies the brand's dedication to efficiency, durability, and performance, making them popular choices for both heating homes and providing a cozy ambiance.

The 49-SCHPM is a powerful pellet stove designed to heat large spaces. It features a spacious hopper that can hold up to 60 pounds of pellets, allowing for extended burn times of up to 80 hours on lower settings. The stove incorporates an easy-to-use digital control board and a built-in thermostat, providing users with precise temperature regulation. This model also boasts a sleek, contemporary design, making it suitable for modern homes while still delivering traditional warmth.

In contrast, the 10-CPM is a compact and efficient pellet stove, ideal for smaller homes or tight spaces. Despite its smaller footprint, it still offers impressive heating capabilities with up to 35,000 BTU output, making it a formidable option for anyone seeking an efficient heat source without sacrificing performance. The 10-CPM features a large viewing window, which enhances the aesthetic appeal and allows users to enjoy the mesmerizing flames. It is also equipped with an automatic ignition system, making it convenient and easy to start.

The 40-TRCPM model showcases England's Stove Works' dedication to versatility. This multi-fuel stove can efficiently burn both wood pellets and corn, allowing homeowners the flexibility to choose their fuel source based on availability and cost. With an output capacity of 40,000 BTU, it is built to dominate larger areas while maintaining a steady heat output. The unit features a sophisticated combustion system that maximizes fuel efficiency and minimizes emissions, aligning with environmentally sustainable practices.

All three models utilize advanced engineering and technology to ensure an optimal burning experience. They come equipped with efficient air circulation systems and adjustable airflow to promote complete combustion, which results in less smoke and creosote buildup. This not only enhances safety but also contributes to the longevity of each unit.

Overall, England's Stove Works has established a strong reputation for producing reliable, efficient, and aesthetically pleasing stoves. The 49-SCHPM, 10-CPM, and 40-TRCPM exemplify the brand's commitment to quality and innovation, making them solid choices for anyone looking to enhance their home's heating system.