Enviro C-10135 owner manual Installation, Deciding Where to Locate Your Pellet Appliance

Page 12

Installation

DECIDING WHERE TO LOCATE YOUR PELLET APPLIANCE:

1.Check clearances to combustibles.

2.Do not obtain combustion air from an attic, garage, or any unventilated space. Combustion air may be obtained from a ventilated crawlspace.

3.Do not install the stove in a bedroom.

4.You can vent the stove through an exterior wall behind the unit or connect it to an existing masonry or metal chimney (must be lined if the chimney is over 6” (15.2cm) in diameter, or over 28 sq. inches (180.6 cm²) cross sectional area). An interior vent can be used with approved pipe passing through the ceiling and roof.

5.Locate the stove in a large and open room that is centrally located in the house. This will optimize heat circulation.

6.The power cord is 8 feet (2.43 m) long and may require a grounded extension cord to reach the nearest electrical outlet.

REMOVING YOUR PELLET APPLIANCE FROM THE PALLET:

To remove your new stove from its pallet, remove the two screws securing the bottom to the pallet. On the freestanding model one can be easily seen from behind but to access the second the ashpan must be removed. On the insert model there is one screw on either side of the bottom.

12

Page 11 Page 13
Image 12
Page 11 Page 13
Contents Meridian Table of Contents Introduction Important Safety Data Safety Warnings and RecommendationsCombustion. See Operation Slider/Damper Setting Rating Label LocationKeep ASH PAN Free of RAW Fuel Automatic Safety Features Operating InstructionsStove Controls Thermostat Installation SLIDER/DAMPER Setting Special NotesComponents more clearly Thermostat / Switch Mode Operating Your Pellet StoveDo not Operate the Unit with the Door or ASH PAN Ajar Turning Your Pellet Stove OFFRoutine Cleaning and Maintenance Tools Required to Clean UnitDo not Place Unburned or RAW Pellet Fuel in ASH PAN Post Season CLEAN-UP Door GlassInstallation Deciding Where to Locate Your Pellet ApplianceRemoving Your Pellet Appliance from the Pallet Freestanding Dimensions Width Floor ProtectionHeight DepthInsert Dimensions Back Wall to Unit 3 inchesVent Termination Requirements Mobile Home Installation Outside Fresh AIR ConnectionFreestanding Insert Through Wall Installation Straight Through the WallStraight Through Wall Installations Through Wall with Vertical Rise InstallationsVertical Installation Hearth Mount Installation Exterior Mounted Exhaust Blower Included in the Exterior Mounted Exhaust Blower KIT areTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installation of Fireplace Insert Pedestal and Leveling Legs Installing Hopper Cover and Adjusting Hopper HeightAssembly and Installation of Insert Surround Panels RemovalPlated Trim Installation Quantity DescriptionRight cab side with upper and lower cabinet trims Top front with top trimPlated Door Installation Door with louversInner side of Meridian door Troubleshooting Do notWhat to do if Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Parts List Part Description NumberDiagramFreestandingSteelParts MeridianParts Diagram Insert SteelComponentsDiagramParts MeridianWarranty To the DealerTo the Distributor Installation Data Sheet Name of Owner Address

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents