Enviro C-10135 owner manual Operating Instructions, Stove Controls, Automatic Safety Features

Page 6

Operating Instructions

STOVE CONTROLS:

 



 



HEAT LEVEL INDICATOR: Shows the Heat Level output setting.

HEAT LEVEL ADJUSTMENT: This button will change the Heat Level output setting of the stove from low to high

ON/OFF BUTTON: Is used to turn the unit ON and OFF

SYSTEM LIGHT: The System Light is responsible for signaling the state of the control board. When the light is flashing during start-up, the stove is in an automatic start mode. When the light is solid, the Heat Level Setting can be altered.

MANUAL AUGER FEED: If the unit runs out of fuel this button can be used to “prime the auger system”. This button will turn off after 60 seconds and then must be released, then pressed again.

 

AUGER LIGHT: This light will flash when the auger motor is energized.

CONVECTION BLOWER CONTROL: Used to turn the convection blower ON/ OFF. If the Blower is left off, and the sensor located on the air jacket reaches 160° F (71° C), the Convection blower will automatically come on HI speed to cool the unit. Leave the convection blower ON for peak efficiency.

AUGER TRIM: The Auger Trim Button is used to increase or decrease the feed rate on LOW, ONLY. Push the Auger Trim button until the number 1 and 5 lights appear on the Heat Level Indicator.

This will increase the feed rate to 4 seconds ON time Auger pulse. This is done only on LOW to allow the burning of poor quality fuels. Push the button until the number 1 and 4 lights appear, this will reduce the Auger On time to 2 second. This setting is for high-grade fuel only. Push the button until just the number 1 light is on, this is for a 3 second on time (standard setting).

3 SECONDS “ON”

2 SECONDS “ON”

4 SECONDS “ON”

Standard Setting

 

 

AUTOMATIC SAFETY FEATURES:

Your pellet Stove has the following safety features:

A)The stove will shut off when the fire goes out and the exhaust temperature drops below 120°F (49°C).

B)The stove has a high temperature safety switch. If the temperature on the hopper reaches 200°F (93°C) the auger will automatically stop, and the stove will shut off when the exhaust temperature cools. If this happens call your local dealer to reset the 200°F (93°C) high limit switch. FIND THE REASONS WHY THE UNIT OVERHEATED.

6

Page 5 Page 7
Image 6
Page 5 Page 7
Contents Meridian Table of Contents Introduction Combustion. See Operation Slider/Damper Setting Important Safety DataSafety Warnings and Recommendations Rating Label LocationKeep ASH PAN Free of RAW Fuel Automatic Safety Features Operating InstructionsStove Controls Thermostat Installation SLIDER/DAMPER Setting Special NotesComponents more clearly Do not Operate the Unit with the Door or ASH PAN Ajar Thermostat / Switch ModeOperating Your Pellet Stove Turning Your Pellet Stove OFFRoutine Cleaning and Maintenance Tools Required to Clean UnitDo not Place Unburned or RAW Pellet Fuel in ASH PAN Post Season CLEAN-UP Door GlassInstallation Deciding Where to Locate Your Pellet ApplianceRemoving Your Pellet Appliance from the Pallet Height Freestanding Dimensions WidthFloor Protection DepthInsert Dimensions Back Wall to Unit 3 inchesVent Termination Requirements Mobile Home Installation Outside Fresh AIR ConnectionFreestanding Insert Through Wall Installation Straight Through the WallStraight Through Wall Installations Through Wall with Vertical Rise InstallationsVertical Installation Hearth Mount Installation Exterior Mounted Exhaust Blower Included in the Exterior Mounted Exhaust Blower KIT areTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installation of Fireplace Insert Pedestal and Leveling Legs Installing Hopper Cover and Adjusting Hopper HeightAssembly and Installation of Insert Surround Panels RemovalRight cab side with upper and lower cabinet trims Plated Trim InstallationQuantity Description Top front with top trimPlated Door Installation Door with louversInner side of Meridian door Troubleshooting Do notWhat to do if Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Parts List Part Description NumberDiagramFreestandingSteelParts MeridianParts Diagram Insert SteelComponentsDiagramParts MeridianWarranty To the DealerTo the Distributor Installation Data Sheet Name of Owner Address

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents