Enviro C-10135 owner manual Assembly and Installation of Insert Surround Panels, Removal

Page 26

Installation

INSTALLATION AND REMOVAL OF CONTROL PANEL IN THE SURROUND PANEL:

When installing the circuit board control panel into the surround panel, the surround does not need to be assembled The circuit board will be found in the firebox.

����

Place the circuit board control panel on the backside of the right surround panel so the hinge is on the outside and the top and bottom holes on the control panel line up with those on the surround. Attach using two T20 screws through the front of the surround into the circuit board control panel.

After the surround has been assembled and is ready to be installed on the the unit plug the wiring harness into the control panel (see top left figure).

REMOVAL:

When maintenance is required on the unit the surround must be removed. Pull the surround straight up till it stops then pull it out about 4” (10cm) and rest the surround on top of the unit while the control panel is removed or disconnected.

If electrical connection is required for the maintenance remove the circuit board control panel from the surround.

If electrical connection is not required for the maintenance remove the wiring harness from the bottom of the circuit board control.

ASSEMBLY AND INSTALLATION OF INSERT SURROUND PANELS:

To assemble the surround panels, lay the panels face down on a soft flat surface and align the outer edges of the sides with the top panel. Using four T20 screws up through the side panels into the top (see top left figure).

Place the assembled surround panel around the stove; align the slots with the screw heads. Push surround in then down to engage the surround slots on the mounting screws (see right). Make sure the top surround panel sits flat behind the

stove top.

26

Page 25 Page 27
Image 26
Page 25 Page 27
Contents Meridian Table of Contents Introduction Combustion. See Operation Slider/Damper Setting Important Safety DataSafety Warnings and Recommendations Rating Label LocationKeep ASH PAN Free of RAW Fuel Stove Controls Automatic Safety FeaturesOperating Instructions Thermostat Installation Components more clearly SLIDER/DAMPER SettingSpecial Notes Do not Operate the Unit with the Door or ASH PAN Ajar Thermostat / Switch ModeOperating Your Pellet Stove Turning Your Pellet Stove OFFDo not Place Unburned or RAW Pellet Fuel in ASH PAN Routine Cleaning and MaintenanceTools Required to Clean Unit Post Season CLEAN-UP Door GlassRemoving Your Pellet Appliance from the Pallet InstallationDeciding Where to Locate Your Pellet Appliance Height Freestanding Dimensions WidthFloor Protection DepthInsert Dimensions Back Wall to Unit 3 inchesVent Termination Requirements Freestanding Insert Mobile Home InstallationOutside Fresh AIR Connection Through Wall Installation Straight Through the WallStraight Through Wall Installations Through Wall with Vertical Rise InstallationsVertical Installation Hearth Mount Installation Exterior Mounted Exhaust Blower Included in the Exterior Mounted Exhaust Blower KIT areTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installation of Fireplace Insert Pedestal and Leveling Legs Installing Hopper Cover and Adjusting Hopper HeightAssembly and Installation of Insert Surround Panels RemovalRight cab side with upper and lower cabinet trims Plated Trim InstallationQuantity Description Top front with top trimInner side of Meridian door Plated Door InstallationDoor with louvers What to do if TroubleshootingDo not Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Parts List Part Description NumberDiagramFreestandingSteelParts MeridianParts Diagram Insert SteelComponentsDiagramParts MeridianTo the Distributor WarrantyTo the Dealer Installation Data Sheet Name of Owner Address

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents