Enviro C-10135 owner manual Thermostat Installation

Page 7

Operating Instructions

C)This unit has a convection fan control over-ride. This function causes the convection fan to reach its full speed when the temperature at the back of the firebox reaches 160° F (71° C). This is a normal safety feature of your unit.

D)The unit is equipped with a vacuum switch to monitor the venting; if it becomes blocked the vacuum switch will turn off the auger and the #2 light on the control board will flash.

THERMOSTAT INSTALLATION:

This stove can be placed into two different thermostat modes:

HI / LOW OPERATION: If the unit has been placed in the HI / LOW mode. The unit will operate on the low setting when the thermostat is not calling for heat. When the thermostat calls for heat, the unit will go to your selected setting which

is displayed on the control board Heat Output Indicator.

ON / OFF OPERATION: If the unit has been placed in the ON /OFF thermostat mode, when the thermostat calls for heat, the unit will go through an ignition sequence and light the stove. Once lit the unit will operate at the selected setting displayed on the control board Heat Output Indicator. Once the thermostat stops calling for heat, the unit will stop feeding pellets and begin its’ shut down sequence until cold then turn off.

1.Install the Low Voltage Thermostat (max 24V) in a location that will effectively monitor the desired area to be heated.

2.Open the right cab side to expose thermostat wires and disconnect. Install 18 gauge (see wiring diagram) or heavier wire through the grommet in the back, from the stove to the thermostat. Connect thermostat wires to red wires provided.

3.To set the thermostat jumper to the desired mode, remove the two screws holding the circuit board control panel in place. Lower the board and pull out to change jumper.

A)HI / LOW: when the jumper is placed on only one of the J9

pins, then the control board is in a HI / LOW mode of thermostat operation (factory setting).

B) ON / OFF: If both pins of J9 are jumped (covered) then the control board is in an ON / OFF mode of thermostat operation.

7

Page 6 Page 8
Image 7
Page 6 Page 8
Contents Meridian Table of Contents Introduction Rating Label Location Important Safety DataSafety Warnings and Recommendations Combustion. See Operation Slider/Damper SettingKeep ASH PAN Free of RAW Fuel Operating Instructions Automatic Safety FeaturesStove Controls Thermostat Installation Special Notes SLIDER/DAMPER SettingComponents more clearly Turning Your Pellet Stove OFF Thermostat / Switch ModeOperating Your Pellet Stove Do not Operate the Unit with the Door or ASH PAN AjarTools Required to Clean Unit Routine Cleaning and MaintenanceDo not Place Unburned or RAW Pellet Fuel in ASH PAN Door Glass Post Season CLEAN-UPDeciding Where to Locate Your Pellet Appliance InstallationRemoving Your Pellet Appliance from the Pallet Depth Freestanding Dimensions WidthFloor Protection HeightBack Wall to Unit 3 inches Insert DimensionsVent Termination Requirements Outside Fresh AIR Connection Mobile Home InstallationFreestanding Insert Straight Through the Wall Through Wall InstallationThrough Wall with Vertical Rise Installations Straight Through Wall InstallationsVertical Installation Hearth Mount Installation Included in the Exterior Mounted Exhaust Blower KIT are Exterior Mounted Exhaust BlowerTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installing Hopper Cover and Adjusting Hopper Height Installation of Fireplace Insert Pedestal and Leveling LegsRemoval Assembly and Installation of Insert Surround PanelsTop front with top trim Plated Trim InstallationQuantity Description Right cab side with upper and lower cabinet trimsDoor with louvers Plated Door InstallationInner side of Meridian door Do not TroubleshootingWhat to do if Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Part Description Number Parts ListMeridian DiagramFreestandingSteelPartsInsert Steel Parts DiagramMeridian ComponentsDiagramPartsTo the Dealer WarrantyTo the Distributor Name of Owner Address Installation Data Sheet

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents