Enviro C-10135 owner manual Troubleshooting, Do not, What to do if

Page 29

Troubleshooting

DO NOT:

●Service the stove with wet hands. The stove is an electrical appliance, which may pose a shock hazard if handled improperly. Only qualified technicians should deal with possible internal electrical failures.

●Do not remove from the firebox any screws without penetrating oil lubrication.

WHAT TO DO IF:

The stove will not start.

The stove will not operate when hot.

The exhaust blower will not function normally.

The convection blower will not function normally.

Ignitor : The pellets will not light.

The auger motor does not function normally.

Control settings (heat level) has no effect on fire.

The stove will not shut off.

The stove keeps going out.

*NOTE: All troubleshooting procedures should be carried out by qualified technicians or installers.

The stove will not start

üMake sure the stove is plugged in and the wall outlet is supplying power..

üIf the Control Board has been placed in the ON /OFF thermostat mode, then turn the thermostat up to call for heat.

üCheck the Heat Level Indicator. - If the # 2 light is flashing (see the # 2 light is flashing)

üIf the unit still does not start, contact your local service dealer for service.

The stove will not operate when hot

üCheck the Heat Level Indicator if a fire is not detected, or if the fire has gone out the #3 light will flash because the Exhaust Temperature Sensor’s contacts have opened.

üCheck the hopper for fuel.

üIncorrect air damper setting. - Excessive air may consume the fire too quickly before the next drop of fuel, leaving completely unburned fuel in the burn pot liner. - Insufficient air will cause build up, further restricting the air flow through the Burn Pot Liner. This in turn will cause the fuel to burn cold and very slowly. Fuel may build up and smother the fire. (NOTE: unit may require a change to the vent system or installation of fresh air to correct Air to Fuel ratio problems).

üCombustion Blower failure. - The Combustion Blower is not turning fast enough to generate the proper vacuum in the fire box. Visual Check – is the blower motor turning.

29

Page 28 Page 30
Image 29
Page 28 Page 30
Contents Meridian Table of Contents Introduction Safety Warnings and Recommendations Important Safety DataCombustion. See Operation Slider/Damper Setting Rating Label LocationKeep ASH PAN Free of RAW Fuel Stove Controls Automatic Safety FeaturesOperating Instructions Thermostat Installation Components more clearly SLIDER/DAMPER SettingSpecial Notes Operating Your Pellet Stove Thermostat / Switch ModeDo not Operate the Unit with the Door or ASH PAN Ajar Turning Your Pellet Stove OFFDo not Place Unburned or RAW Pellet Fuel in ASH PAN Routine Cleaning and MaintenanceTools Required to Clean Unit Door Glass Post Season CLEAN-UPRemoving Your Pellet Appliance from the Pallet InstallationDeciding Where to Locate Your Pellet Appliance Floor Protection Freestanding Dimensions WidthHeight DepthBack Wall to Unit 3 inches Insert DimensionsVent Termination Requirements Freestanding Insert Mobile Home InstallationOutside Fresh AIR Connection Straight Through the Wall Through Wall InstallationThrough Wall with Vertical Rise Installations Straight Through Wall InstallationsVertical Installation Hearth Mount Installation Included in the Exterior Mounted Exhaust Blower KIT are Exterior Mounted Exhaust BlowerTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installing Hopper Cover and Adjusting Hopper Height Installation of Fireplace Insert Pedestal and Leveling LegsRemoval Assembly and Installation of Insert Surround PanelsQuantity Description Plated Trim InstallationRight cab side with upper and lower cabinet trims Top front with top trimInner side of Meridian door Plated Door InstallationDoor with louvers What to do if TroubleshootingDo not Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Part Description Number Parts ListMeridian DiagramFreestandingSteelPartsInsert Steel Parts DiagramMeridian ComponentsDiagramPartsTo the Distributor WarrantyTo the Dealer Name of Owner Address Installation Data Sheet

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents