Enviro C-10135 owner manual Keep ASH PAN Free of RAW Fuel

Page 5

Introduction

Glass: Do not abuse the glass by striking or slamming the door. Do not attempt to operate the stove with broken glass. The stove uses ceramic glass. Replacement glass must be purchased from an ENVIRO dealer. Do not attempt to open the door and clean the glass while the unit is in operation or if glass is hot.

Flammable Liquids: Never use gasoline, gasoline-type lantern fuel, kerosene, charcoal lighter fluid, or similar liquids to start or “freshen up” a fire in the heater. Keep all such liquids well away from the heater while it is in use.

Smoke Detector: Smoke detectors should be installed and maintained in the structure when installing and operating a pellet burning appliance.

Operation: The ash pan and door must be closed securely for proper and safe operation of the pellet stove. Also ensure all gaskets on the door are checked and replaced when necessary.

KEEP ASH PAN FREE OF RAW FUEL.

DO NOT PLACE UNBURNED OR NEW PELLET FUEL IN ASH PAN. A fire in the ash pan may occur.

Installation: Be sure to maintain the structural integrity of your home when passing a vent through walls, ceilings, or roofs.

DO NOT INSTALL A FLUE DAMPER IN THE EXHAUST VENTING SYSTEM OF THIS UNIT. DO NOT CONNECT THIS UNIT TO A CHIMNEY FLUE SERVING ANOTHER APPLIANCE.

Fresh air: Must be connected to all units installed in Mobile Homes as well as “Air Tight Homes” (R2000). Fresh air intake is recommended on all installations. Failure to install intake air may result in poor performance, smoke, property damage, house fire, bodily injury, or death under certain conditions.

If you have any questions with regards to your stove or the above-mentioned information, please feel free to contact your local dealer for further clarification and comments.

SINCE SHERWOOD INDUSTRIES LTD. HAS NO CONTROL OVER THE INSTALLATION OF YOUR STOVE, SHERWOOD INDUSTRIES LTD. GRANTS NO WARRANTY IMPLIED OR STATED FOR THE INSTALLATION OR MAINTENANCE OF YOUR STOVE.

THEREFORE, SHERWOOD INDUSTRIES LTD. ASSUMES NO RESPONSIBILITY FOR ANY CONSEQUENTIAL DAMAGE(S).

SAVE THIS INSTRUCTION MANUAL FOR FUTURE REFERENCE

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Meridian Table of Contents Introduction Safety Warnings and Recommendations Important Safety DataCombustion. See Operation Slider/Damper Setting Rating Label LocationKeep ASH PAN Free of RAW Fuel Stove Controls Automatic Safety FeaturesOperating Instructions Thermostat Installation Components more clearly SLIDER/DAMPER SettingSpecial Notes Operating Your Pellet Stove Thermostat / Switch ModeDo not Operate the Unit with the Door or ASH PAN Ajar Turning Your Pellet Stove OFFDo not Place Unburned or RAW Pellet Fuel in ASH PAN Routine Cleaning and MaintenanceTools Required to Clean Unit Door Glass Post Season CLEAN-UPRemoving Your Pellet Appliance from the Pallet InstallationDeciding Where to Locate Your Pellet Appliance Floor Protection Freestanding Dimensions WidthHeight DepthBack Wall to Unit 3 inches Insert DimensionsVent Termination Requirements Freestanding Insert Mobile Home InstallationOutside Fresh AIR Connection Straight Through the Wall Through Wall InstallationThrough Wall with Vertical Rise Installations Straight Through Wall InstallationsVertical Installation Hearth Mount Installation Included in the Exterior Mounted Exhaust Blower KIT are Exterior Mounted Exhaust BlowerTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installing Hopper Cover and Adjusting Hopper Height Installation of Fireplace Insert Pedestal and Leveling LegsRemoval Assembly and Installation of Insert Surround PanelsQuantity Description Plated Trim InstallationRight cab side with upper and lower cabinet trims Top front with top trimInner side of Meridian door Plated Door InstallationDoor with louvers What to do if TroubleshootingDo not Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Part Description Number Parts ListMeridian DiagramFreestandingSteelPartsInsert Steel Parts DiagramMeridian ComponentsDiagramPartsTo the Distributor WarrantyTo the Dealer Name of Owner Address Installation Data Sheet

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents