Enviro C-10135 Plated Door Installation, Door with louvers, Inner side of Meridian door

Page 28

Installation

 

REMOVAL OF LOUVER BAR SET:

 

 

Door must be open. The three arrows in figure 3 point to three of the

 

nuts that hold the louvers on. There are three nuts on each end. Remove

 

the six nuts by hand; if the nuts are tight, a 11/32” socket can be used.

 

When removing the louvers, pull one end of the louver up over the stud.

 

If it is difficult to remove the louver, push on one side from the front, then

 

pull the other end off the second stud.

 

REPLACEMENT OF LOUVER BAR SET:

 

Place one slotted end of new louver over a stud, then slide the other slot

 

over the corresponding stud; replace the nuts and hand tighten. Close

 

door when all three louvers are replaced.

 

CLEANING THE TRIMS:

 

Painted surfaces should be wiped with a damp cloth periodically. It

 

is important to note that fingerprints and other marks can leave a

Door with louvers.

permanent stain on plated finishes. To avoid this, give the surface a

quick wipe with denatured alcohol on a soft cloth BEFORE lighting the fireplace. Never clean surfaces when they are hot. Do not use other cleaners or abrasives as they may leave a residue or scratches, which can become permanently etched into the surface.

PLATED DOOR INSTALLATION:

TO AVOID PERSONAL INJURY DO NOT REMOVE OR REPLACE COVER WHEN PELLET STOVE IS HOT!

TOOLS REQUIRED:

●11/32” socket or wrench

REMOVAL OF DOOR COVER:

When stove is off and cool, open the door. Remove the four #8 hex nuts around the inside of the glass retainer shown in Figure 1.

Remove door cover from door by gently sliding the studs out of the holes. If it is difficult to remove the cover, the glass retainer may be pinching the threads on the studs. Slightly loosen the four screws (by each of the studs).

REPLACEMENT OF DOOR COVER:

Slide new door cover into place and hand tighten the four #8 hex nuts around the inside of the glass retainer. Ensure the four screws are also

hand tight and close door.

 

CLEANING THE DOOR COVER:

Inner side of Meridian door.

 

Painted surfaces should be wiped with a damp cloth periodically. It is important to note that fingerprints and other marks can leave a permanent stain on plated finishes. To avoid this, give the door a quick wipe with denatured alcohol on a soft cloth BEFORE lighting the stove. Never clean surfaces when hot. Do not use other cleaners or abrasives as they may leave a residue or scratches, which can become permanently etched into the surface.

28

Page 27 Page 29
Image 28
Page 27 Page 29
Contents Meridian Table of Contents Introduction Important Safety Data Safety Warnings and RecommendationsCombustion. See Operation Slider/Damper Setting Rating Label LocationKeep ASH PAN Free of RAW Fuel Operating Instructions Automatic Safety FeaturesStove Controls Thermostat Installation Special Notes SLIDER/DAMPER SettingComponents more clearly Thermostat / Switch Mode Operating Your Pellet StoveDo not Operate the Unit with the Door or ASH PAN Ajar Turning Your Pellet Stove OFFTools Required to Clean Unit Routine Cleaning and MaintenanceDo not Place Unburned or RAW Pellet Fuel in ASH PAN Post Season CLEAN-UP Door GlassDeciding Where to Locate Your Pellet Appliance InstallationRemoving Your Pellet Appliance from the Pallet Freestanding Dimensions Width Floor ProtectionHeight DepthInsert Dimensions Back Wall to Unit 3 inchesVent Termination Requirements Outside Fresh AIR Connection Mobile Home InstallationFreestanding Insert Through Wall Installation Straight Through the WallStraight Through Wall Installations Through Wall with Vertical Rise InstallationsVertical Installation Hearth Mount Installation Exterior Mounted Exhaust Blower Included in the Exterior Mounted Exhaust Blower KIT areTo Supply Power to the Exhaust Blower Through Wall Vertical Installation Masonry Fireplace Insert Installation Installation of Fireplace Insert Pedestal and Leveling Legs Installing Hopper Cover and Adjusting Hopper HeightAssembly and Installation of Insert Surround Panels RemovalPlated Trim Installation Quantity DescriptionRight cab side with upper and lower cabinet trims Top front with top trimDoor with louvers Plated Door InstallationInner side of Meridian door Do not TroubleshootingWhat to do if Exhaust motor will not function normally Auger light flashes but auger motor does not turn at all Wiring Diagram Parts List Part Description NumberDiagramFreestandingSteelParts MeridianParts Diagram Insert SteelComponentsDiagramParts MeridianTo the Dealer WarrantyTo the Distributor Installation Data Sheet Name of Owner Address

C-10135 specifications

Enviro C-10135 is a cutting-edge solution that has emerged to address the growing concerns in environmental management and sustainability. Designed to meet the demands of modern industries, it incorporates a wide array of features and technologies that set it apart in the field.

One of the standout characteristics of Enviro C-10135 is its innovative waste management capabilities. The system employs advanced sorting and recycling technologies that enable efficient separation of contaminants from recyclable materials. This not only streamlines the recycling process but also significantly reduces the volume of waste sent to landfills. With a focus on circular economy principles, Enviro C-10135 helps industries adopt more sustainable practices while minimizing their environmental footprint.

The technology behind Enviro C-10135 is grounded in real-time data analytics. Integrated sensors monitor environmental conditions and waste composition continuously. This data is processed using advanced algorithms that provide actionable insights for waste management strategies. As a result, users can optimize operational efficiency, reduce costs, and enhance compliance with regulatory requirements.

Another key feature of Enviro C-10135 is its adaptability. The system can be customized to fit the specific needs of various industries, ranging from manufacturing to hospitality. Manufacturers can modify its settings to handle different types of waste, while facilities in the hospitality sector benefit from tailored solutions for food waste and packaging materials. This versatility makes Enviro C-10135 an attractive choice for businesses of all sizes.

Energy efficiency is also a salient characteristic of the Enviro C-10135. The system is engineered to minimize power consumption without compromising performance. It employs energy recovery technologies that harness excess energy generated during waste processing, which can be redirected for operational needs. This aspect not only lowers operational costs but also contributes to sustainability goals.

In addition to its technological prowess, Enviro C-10135 is user-friendly. The interface is designed to provide intuitive navigation for operators, easing the learning curve and ensuring efficient operation. Training programs and support are also available to assist users in maximizing the system's potential.

In summary, Enviro C-10135 is at the forefront of environmental technology, offering advanced waste management features, real-time monitoring and analytics, adaptability for various applications, energy efficiency, and user-friendly operation. As industries strive to meet sustainability targets, Enviro C-10135 stands as a vital asset in achieving these goals and fostering a cleaner, more sustainable future.
Top Page Image Contents