Axis Communications Q7401 user manual Network, Basic TCP/IP Settings

Page 47

AXIS Q7401 Video Encoder

System Options

Network

Basic TCP/IP Settings

The Axis product supports IP version 4 and IP version 6. Both versions can be enabled simultaneously, and at least one version must always be enabled.

IPv4 Address Configuration

By default, the Axis product is set to use IPv4 (IP version 4) and to obtain the IP address automatically via DHCP. The IPv4 settings are configured under System Options > Network > TCP/IP > Basic.

DHCP (Dynamic Host Configuration Protocol) allows network administrators to centrally manage and automate the assignment of IP addresses. DHCP should only be enabled if using dynamic IP address notification, or if the DHCP can update a DNS server. It is then possible to access the Axis product by name (host name).

If DHCP is enabled and the product cannot be accessed, run AXIS IP Utility to search the network for connected Axis products, or reset the product to the factory default settings (see page 56) and then perform the installation again.

To use a static IP address, check Use the following IP address and specify the IP address, subnet mask and default router.

IPv6 Address Configuration

If IPv6 (IP version 6) is enabled, the Axis product will receive an IP address according to the configuration in the network router.

To enable IPv6, go to System Options > Network > TCP/IP > Basic. Other settings for IPv6 should be configured in the network router.

ARP/Ping

The product’s IP address can be assigned using ARP and Ping. For instructions, see Assign IP Address Using ARP/Ping on page 47.

The ARP/Ping service is enabled by default but is automatically disabled two minutes after the product is started, or as soon as an IP address is assigned. To re-assign IP address using ARP/Ping, the product must be restarted to enable ARP/Ping for an additional two minutes.

To disable the service, go to System Options > Network > TCP/IP > Basic and clear the option Enable ARP/Ping setting of IP address.

Pinging the product is still possible when the service is disabled.

Assign IP Address Using ARP/Ping

The product's IP address can be assigned using ARP/Ping. The command must be issued within 2 minutes of connecting power.

1.Acquire a free static IP address on the same network segment as the computer.

2.Locate the serial number (S/N) on the product label.

3.Open a command prompt and enter the following commands:

Linux/Unix syntax

arp -s <IP address> <serial number> temp ping -s 408 <IP address>

Linux/Unix example

arp -s 192.168.0.125 00:40:8c:18:10:00 temp ping -s 408 192.168.0.125

Windows syntax (this may require that you run the command prompt as an administrator) arp -s <IP address> <serial number>

47

Page 46 Page 48
Image 47
Page 46 Page 48
Contents Axis Q7401 Video Encoder Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis Q7401 Video Encoder Table of ContentsConnectors Performance Considerations Hardware Overview Connectors and Buttons Status LED Indication LED IndicatorsPower LED Indication Control ButtonAccess from a Browser Access the ProductSet the Root Password Access from the InternetManual Trigger Go to Setup EventsLive View Controls on the Live ViewAMC Audio Controls Axis Media Control viewer toolbarPTZ Controls To show the manual trigger buttons in the Live ViewPreset Positions on Axis Media Control AMC How to Stream H.264Media Streams QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductPixel Counter Set Up Video StreamsVideo and Audio 264 Pixel counter can be accessed fromClick Save to apply the new settings ImageVideo input Camera SettingsStream Profiles Image AppearanceGo to Video & Audio Overlay Image OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Events Action Rules Use Overlay Text in an Action RuleAudio Input Set Up AudioPrivacy Mask Audio ModesAudio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewOutput Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis Q7401 Video Encoder Guard Tour Preset PositionsPTZ Pan Tilt Zoom Go to PTZ Guard Tour and click Add Device SettingsAdvanced ControlsOSD Menu Install PTZ DriverOperator Same as administrator but with lower priority Control QueueGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q7401 Video Encoder Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesTriggers Recipient Types Add RecipientsActions Go to Events Schedules and click Add Set Up Email RecipientsCreate Schedules Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingClick Save to save and start the recording Languages IP Address Filter System OptionsSecurity UsersGo to System Options Security Ieee IeeeCertificates Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardCOM Port Ports & DevicesNetwork Share PortsSupport Overview MaintenanceSupport Port StatusFile Upload Plain ConfigLogs & Reports ScriptingReset to Factory Default Settings Check the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsEmergency Recovery Procedure Problems setting the IP addressBasic Product is accessible locally but not externallyProblems with streaming H.264 Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsVideo cannot be recorded Technical Specifications Weight Function/group Specifications System ApplicationPower ConnectorsFunction Pin Specifications ConnectorsAudio Output RS-485/422 ConnectorPerformance Considerations Audio InputAxis Q7401 Video Encoder M2.4
Related manuals
Manual 82 pages 36.24 Kb

Q7401 specifications

The Axis Communications Q7401 is a powerful and versatile video encoder designed for transforming analog video signals into high-quality digital streams. This device is part of Axis' comprehensive line of video surveillance solutions, catering to a broad array of applications ranging from retail and transportation to public safety and critical infrastructure monitoring.

One of the standout features of the Q7401 is its support for multiple video formats, including H.264 and Motion JPEG. This versatile encoding capability ensures that users can choose the video quality and bandwidth that best suit their needs. The H.264 compression, in particular, provides a significant reduction in bandwidth and storage requirements while maintaining exceptional video quality, making it an ideal choice for environments where efficiency is crucial.

Equipped with a two-way audio feature, the Q7401 enables real-time communication between the camera and the control center, enhancing situational awareness and response capabilities. This feature is increasingly valuable in security applications, allowing operators to interact proactively with on-site personnel or potential intruders.

The Q7401 also includes advanced features such as video motion detection, which allows the user to set up alerts based on detected motion within predefined areas. This capability reduces the need for constant monitoring, automatically notifying users of potential security breaches or events of interest.

In terms of connectivity, the Axis Q7401 is designed to integrate seamlessly with Axis' network video products. Its compatibility with various Axis applications enhances its functionality, allowing for advanced analytics and intelligent features that can further enhance security measures.

The robust design of the Q7401 ensures reliability in various environments. Its compact form factor allows for easy installation in space-constrained locations, and it operates efficiently in temperature variations, making it suitable for both indoor and outdoor use.

Additionally, the device supports Power over Ethernet (PoE), simplifying the installation process by allowing both power and data transmission through a single cable, thus reducing the amount of wiring required.

Overall, the Axis Communications Q7401 is an excellent choice for organizations looking to upgrade their surveillance systems to meet modern security demands while benefiting from advanced features and reliable performance.
Top Page Image Contents