Axis Communications Q7401 user manual UPnPTM, RTP/H.264, Bonjour

Page 51

AXIS Q7401 Video Encoder

System Options

SNMP

The Simple Network Management Protocol (SNMP) allows remote management of network devices. An SNMP community is the group of devices and management station running SNMP. Community names are used to identify groups.

To enable and configure SNMP in the Axis product, go to the System Options > Network > SNMP page.

Depending on the level of security required, select the version on SNMP to use.

Traps are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

Note

If HTTPS is enabled, SNMP v1 and SNMP v2c should be disabled.

Traps for SNMP v1/v2 are used by the Axis product to send messages to a management system on important events and status changes. Check Enable traps and enter the IP address where the trap message should be sent and the Trap community that should receive the message.

The following traps are available:

•Cold start

•Warm start

•Link up

•Authentication failed

SNMP v3 provides encryption and secure passwords. To use traps with SNMP v3, an SNMP v3 management application is required.

To use SNMP v3, HTTPS must be enabled, see HTTPS on page 44. To enable SNMP v3, check the box and provide the initial user password.

Note

The initial password can only be set once. If the password is lost, the Axis product must be reset to factory default, see Reset to Factory Default Settings on page 56.

UPnPTM

The Axis product includes support for UPnPTM. UPnPTM is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

UPnPTM can be disabled under System Options > Network > UPnPTM.

RTP/H.264

The RTP port range and multicast settings are configured under System Options > Network > RTP.

The RTP port range defines the range of ports from which the video/audio ports are automatically selected. For multicast streams, only certain IP addresses and port numbers should be used.

Select Always Multicast Video and/or Always Multicast Audio to start multicast streaming without opening an RTSP session.

Bonjour

The Axis product includes support for Bonjour. Bonjour is enabled by default and the product is automatically detected by operating systems and clients that support this protocol.

Bonjour can be disabled under System Options > Network > Bonjour.

51

Page 50 Page 52
Image 51
Page 50 Page 52
Contents Axis Q7401 Video Encoder Intellectual Property Rights About this documentLegal Considerations LiabilityLearn More SupportAxis Q7401 Video Encoder Table of ContentsConnectors Performance Considerations Hardware Overview Connectors and Buttons Status LED Indication LED IndicatorsPower LED Indication Control ButtonAccess from a Browser Access the ProductSet the Root Password Access from the InternetManual Trigger Go to Setup EventsLive View Controls on the Live ViewAMC Audio Controls Axis Media Control viewer toolbarPTZ Controls To show the manual trigger buttons in the Live ViewPreset Positions on How to Stream H.264 Media StreamsAxis Media Control AMC QuickTimeTM. The following paths can be used Alternative Methods of Accessing the Video StreamJava applet supports simplex audio with G.711 encoding Access Audio StreamsBasic Setup Set Up the ProductSet Up Video Streams Video and AudioPixel Counter 264 Pixel counter can be accessed fromClick Save to apply the new settings ImageVideo input Camera SettingsStream Profiles Image AppearanceGo to Video & Audio Overlay Image OverlayOverlay Image Go to Video & Audio Video Stream and select the Image tabGo to Events Action Rules Use Overlay Text in an Action RuleAudio Input Set Up AudioPrivacy Mask Audio ModesAudio Output Audio ClipsDefault Viewer for Browsers Configure the Live ViewOutput Buttons Viewer SettingsGo to Setup Live View Config User Defined LinksAxis Q7401 Video Encoder Preset Positions PTZ Pan Tilt ZoomGuard Tour Go to PTZ Guard Tour and click Add Device SettingsAdvanced ControlsOSD Menu Install PTZ DriverOperator Same as administrator but with lower priority Control QueueGo to Detectors Camera Tampering DetectorsCamera Tampering Motion DetectionParameter Object Size History Sensitivity Description Set Up Motion Detection WindowsMotion Detection Parameters Go to Detectors Motion DetectionAudio Detection Application Licenses Install ApplicationGo to Setup Applications ApplicationsAxis Q7401 Video Encoder Go to Events Action Rules and click Add Set Up Action RulesEvents Convert Event Types to Action RulesTriggers Add Recipients ActionsRecipient Types Set Up Email Recipients Create SchedulesGo to Events Schedules and click Add Go to Events Recurrences and click Add Set Up RecurrencesGo to Recordings List RecordingsRecording List Continuous RecordingClick Save to save and start the recording Languages IP Address Filter System OptionsSecurity UsersIeee CertificatesGo to System Options Security Ieee Audio Support Go to Setup System Options Security CertificatesClick Install certificate and upload the certificate Date & TimeNetwork Basic TCP/IP SettingsDNS Configuration Advanced TCP/IP SettingsAxis Internet Dynamic DNS Service Axis Internet Dynamic DNS Service requires IPv4NAT traversal port mapping for IPv4 NTP ConfigurationHost Name Configuration Link-Local IPv4 AddressFTP QoS Quality of ServiceBonjour UPnPTM can be disabled under System Options Network UPnPTMUPnPTM RTP/H.264Format SD Card StorageSD Card Mount and Unmount SD CardCOM Port Ports & DevicesNetwork Share PortsSupport Overview MaintenanceSupport Port StatusFile Upload Plain ConfigLogs & Reports ScriptingReset to Factory Default Settings Check the Firmware TroubleshootingUpgrade the Firmware Firmware To upgrade the product’s firmwareProduct cannot be accessed from a browser Symptoms, Possible Causes and Remedial ActionsEmergency Recovery Procedure Problems setting the IP addressProduct is accessible locally but not externally Problems with streaming H.264Basic Settings Status and Network indicator LEDs are flashing red rapidlyVideo and image problems, general Setup Video & Audio Camera SettingsVideo cannot be recorded Technical Specifications Weight Function/group Specifications System ApplicationPower ConnectorsFunction Pin Specifications ConnectorsAudio Output RS-485/422 ConnectorPerformance Considerations Audio InputAxis Q7401 Video Encoder M2.4
Related manuals
Manual 82 pages 36.24 Kb

Q7401 specifications

The Axis Communications Q7401 is a powerful and versatile video encoder designed for transforming analog video signals into high-quality digital streams. This device is part of Axis' comprehensive line of video surveillance solutions, catering to a broad array of applications ranging from retail and transportation to public safety and critical infrastructure monitoring.

One of the standout features of the Q7401 is its support for multiple video formats, including H.264 and Motion JPEG. This versatile encoding capability ensures that users can choose the video quality and bandwidth that best suit their needs. The H.264 compression, in particular, provides a significant reduction in bandwidth and storage requirements while maintaining exceptional video quality, making it an ideal choice for environments where efficiency is crucial.

Equipped with a two-way audio feature, the Q7401 enables real-time communication between the camera and the control center, enhancing situational awareness and response capabilities. This feature is increasingly valuable in security applications, allowing operators to interact proactively with on-site personnel or potential intruders.

The Q7401 also includes advanced features such as video motion detection, which allows the user to set up alerts based on detected motion within predefined areas. This capability reduces the need for constant monitoring, automatically notifying users of potential security breaches or events of interest.

In terms of connectivity, the Axis Q7401 is designed to integrate seamlessly with Axis' network video products. Its compatibility with various Axis applications enhances its functionality, allowing for advanced analytics and intelligent features that can further enhance security measures.

The robust design of the Q7401 ensures reliability in various environments. Its compact form factor allows for easy installation in space-constrained locations, and it operates efficiently in temperature variations, making it suitable for both indoor and outdoor use.

Additionally, the device supports Power over Ethernet (PoE), simplifying the installation process by allowing both power and data transmission through a single cable, thus reducing the amount of wiring required.

Overall, the Axis Communications Q7401 is an excellent choice for organizations looking to upgrade their surveillance systems to meet modern security demands while benefiting from advanced features and reliable performance.
Top Page Image Contents