GTO 352 installation manual Post Bracket Assembly, Open Installation beginning on

Page 17

Determining the Mounting Position

of the Post Bracket Assembly and the Gate Bracket

Step 3

Insert the 3/8" x 2" bolt through the center hole of the post brackets and post pivot bracket as shown. Fasten a

3/8" washer, 3/8" lock

washer and 3/8" nut on the end of the bolt. DO NOT overtighten the nut because the post pivot bracket will have to be adjusted later.

Post Bracket Assembly

3/8" x 2" Bolt

Post Bracket

Post Pivot Bracket

Post Bracket

3/8" Washer

3/8" Lock Washer

3/8" Nut

NOTE: The following steps are intended for pull-to-opengate installations. If you are mounting your opener on a push-to- open gate (e.g., a gate on a sloped driveway) you will need to purchase a Push To Open bracket (FM148) (see Accessory

catalog). Also, see Push-to-

Open Installation beginning on page 36.

Step 4

Attach post bracket assembly and gate bracket to the opener with the clevis pins and bushings. Secure the clevis pins with hairpin clips.

Clevis Pin

Rear Mount

Bushing

Opener

Hairpin Clip

Post Bracket Assembly

Front Mount

Clevis Pin

Gate Bracket

Bushing

Hairpin Clip

Step 5

With the gate in the open position (up to 110º from its closed position), and the opener fully retracted, adjust the post bracket assembly and gate bracket until the opener is level. While holding the opener level, use C-clamps to temporarily keep the post bracket assembly and gate bracket in their respective positions on the fence post and gate.

Post Bracket Assembly

Level Opener

Gate In Open Position

Fence Post

Gate Bracket

M i g h t y M u l e 3 5 2

13

Image 17
Contents 352 Place of Purchase Conversion ChartWhen You Know Multiply By To Find Table of Contents Please Read this First Disconnecting the Opener Important Safety InstructionsPull-To-Open Application Entrapment Zones for aPath of a Moving Gate ZoneMoving Gate Area Driveway II. During InstallationAny control device within gray area III. After Installation Secondary Means of Protection Against Entrapment Entrapment Protection Required Safety Precautions for GatesInstall Warning Signs 352 Hardware Bag Contents Parts List Opener and Mounting HardwareTools Needed Drive PowerControl Operational CapacityPreparation of the Gate Installation OverviewPull-to-Open Gates Gate Opens into the Property StepRecommended Reinforcement Examples Installation of Mounting HardwareOpen Installation beginning on Post Bracket AssemblyBe sure gate opener and bracket dont bind GateGate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate Bracket StepMounting the Second Opener Installation of the Closed Position StopsMounting the Master Opener Illustration B Second Gate Opener Check ListPreparing to Connect the Wires Trench and Lay Conduit for WiringCable Communication Second ConduitON/OFF Solar Panel and Gate Activity Chart Powering Options Transformer or SolarConnecting The Battery Important Information about LOW Voltage Wire Connecting the TransformerMaster Arm Make sure the exposed wires do not touch each otherMaster Control Board Settings DIP Switches Connecting Solar PanelsMain DIP Switch Settings Modes Pull Push MODE1 MODE2 LOCK/BEACONSetting Auto-Close Time Stall Force Potentiometer SettingControl Board Close T IM ERun the cable through PVC conduit to protect it from damage Installing the ReceiverYour Mighty Mule 352 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Testing Your Closed Limit SettingLearn Remote Button Setting Your Personal Transmitter CodeConnecting Additional Safety Devices Solar Panel Control Board Connections18 VAC Solar Panel +GTO Automatic Lock Connecting AccessoriesSecond Opener Routing Wires Through The Access PanelMaster Opener Final Step When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationPress the SET Limit on the Master ARM for 5 Seconds Setting the Open Position LimitClearing Programmed Open Limit Setting Testing Your Open Limit SettingVisual/LEDs Feedback Visual and Audible Diagnostic IndicatorsAudible/Buzzer/Alarm Feedback Power LED Green Master ARM only Learn Limit ModeGate Closes Then Opens Again on its Own Gate Opens Then Closes Again on its OwnGTO, Inc. Technical Service Department is open Repair ServiceGTO, Inc GateIf this Opener will be Used with Gates That are Mounted on Column Installation InformationMASONRY, BRICK, or Rock etc. Columns Read the Following Carefully Before ProceedingAccessories are Available From Your Retail Store AccessoriesAutomatic Gate Lock Pull-to-Open FM143

352 specifications

The GTO 352 is an innovative piece of engineering designed to meet the demands of modern users in various sectors, including transportation, logistics, and construction. This versatile machine stands out due to its robust design and advanced features that enhance productivity and efficiency on site.

One of the GTO 352’s main features is its powerful engine, which is designed to deliver outstanding performance while remaining fuel-efficient. The state-of-the-art powertrain not only ensures high torque but also reduces greenhouse gas emissions, making it an environmentally friendly choice for heavy-duty applications.

The GTO 352 is equipped with an advanced hydraulic system that allows for precise control when lifting and moving heavy loads. This system is complemented by its user-friendly interface, giving operators the ability to easily adjust settings and parameters for optimum performance. The machine's hydraulic capabilities can accommodate a variety of attachments, enhancing versatility and making it suitable for multiple tasks, from lifting to material handling.

In terms of design, the GTO 352 prioritizes operator comfort and safety. Its spacious cabin features ergonomically designed seating and intuitive controls, reducing fatigue during long working hours. Additionally, the machine is equipped with various safety features, including stability monitoring and automatic shut-off systems that ensure the well-being of the operator and surrounding personnel.

Another significant characteristic of the GTO 352 is its adaptability to various terrains. With a robust chassis and durable tires, it can handle rough and uneven surfaces, making it suitable for construction sites, warehouses, and rural areas alike. The machine’s all-wheel drive system improves traction and maneuverability, allowing for efficient operation in challenging conditions.

Technologically, the GTO 352 incorporates advanced sensors and software that allow for real-time monitoring of performance metrics. This data-driven approach enables users to make informed decisions regarding maintenance and operation, thereby extending the machine's life cycle and enhancing its operational efficiency.

Overall, the GTO 352 stands as a hallmark of innovation in its class. Its powerful performance, versatility, user-friendly design, and commitment to safety and efficiency make it an essential tool for professionals across various industries. As the world continues to move toward more sustainable and efficient practices, the GTO 352 promises to play a crucial role in meeting those demands.