GTO 352 installation manual Important Safety Instructions, Disconnecting the Opener

Page 5

IMPORTANT SAFETY INSTRUCTIONS

Because automatic gate openers produce high levels of force, consumers need to know the potential hazards associated with improperly designed, installed, and maintained automated gate opener systems. Keep in mind that the gate opener is just one component of the total gate operating system. Each component must work in unison to provide the consumer with convenience, security, and safety.

This manual contains various safety precautions and warnings for the consumer. Because there are many possible applications of the gate opener, the safety precautions and warnings contained in this manual cannot be completely exhaustive in nature. They do, however, provide an overview of the safe design, installation, and use of this product. CAREFULLY READ AND FOLLOW ALL SAFETY PRECAUTIONS,

WARNINGS, AND INSTALLATION INSTRUCTIONS TO ENSURE THE SAFE SYSTEM DESIGN, INSTALLATION, AND USE OF THIS PRODUCT.

Precautions and warnings in this manual are identified with this warning symbol. The symbol identifies conditions that can result in damage to the opener or its components, serious injury, or death.

Because GTO automatic gate openers are only part of the total gate operating system, it is the responsibility of the consumer to ensure that the total system is safe for its intended use.

To Manually Open and Close the Gate, Follow the Procedure Below:

CAUTION: The gate will move freely and uncontrolled when the gate opener is removed from the gate. ONLY disconnect the opener when the opener power switch is OFF and the gate is NOT moving.

Disconnecting the Opener

1.Turn opener power switch OFF.

2.Remove hairpin clip, clevis pin, and bushing from the front mounting point.

3.Remove the opener from the mount.

The gate can be opened and closed manually when the opener is disconnected.

Front Mount

Clevis Pin

Gate Bracket

IMPORTANT: NEVER allow opener arm to hang by the front mount - it will break from the arm weight.

CAUTION: Because the Mighty Mule gate opener is battery powered, disconnect the opener ONLY when the power switch on the opener is turned OFF. Unplugging the transformer does not turn power to the opener OFF.

NOTE: Substitute a Pin Lock (FM133) for the clevis pin on the front mount only of the gate opener to prevent unauthorized removal of the opener from the gate (see Accessory Catalog).

0caVW\U

Hairpin Clip

M i g h t y M u l e 3 5 2

1

Page 4 Page 6
Image 5
Page 4 Page 6
Contents 352 Place of Purchase Conversion ChartWhen You Know Multiply By To Find Table of Contents Please Read this First Disconnecting the Opener Important Safety InstructionsPull-To-Open Application Entrapment Zones for aPath of a Moving Gate ZoneMoving Gate Area Driveway II. During InstallationAny control device within gray area III. After Installation Secondary Means of Protection Against Entrapment Entrapment Protection Required Safety Precautions for GatesInstall Warning Signs 352 Hardware Bag Contents Parts List Opener and Mounting HardwareTools Needed Drive PowerControl Operational CapacityPreparation of the Gate Installation OverviewPull-to-Open Gates Gate Opens into the Property StepRecommended Reinforcement Examples Installation of Mounting HardwareOpen Installation beginning on Post Bracket AssemblyBe sure gate opener and bracket dont bind GateGate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate Bracket StepMounting the Second Opener Installation of the Closed Position StopsMounting the Master Opener Illustration B Second Gate Opener Check ListPreparing to Connect the Wires Trench and Lay Conduit for WiringCable Communication Second ConduitON/OFF Solar Panel and Gate Activity Chart Powering Options Transformer or SolarConnecting The Battery Important Information about LOW Voltage Wire Connecting the TransformerMaster Arm Make sure the exposed wires do not touch each otherMaster Control Board Settings DIP Switches Connecting Solar PanelsMain DIP Switch Settings Modes Pull Push MODE1 MODE2 LOCK/BEACONSetting Auto-Close Time Stall Force Potentiometer SettingControl Board Close T IM ERun the cable through PVC conduit to protect it from damage Installing the ReceiverYour Mighty Mule 352 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Testing Your Closed Limit SettingLearn Remote Button Setting Your Personal Transmitter CodeConnecting Additional Safety Devices Solar Panel Control Board Connections18 VAC Solar Panel +GTO Automatic Lock Connecting AccessoriesSecond Opener Routing Wires Through The Access PanelMaster Opener Final Step When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationPress the SET Limit on the Master ARM for 5 Seconds Setting the Open Position LimitClearing Programmed Open Limit Setting Testing Your Open Limit SettingVisual/LEDs Feedback Visual and Audible Diagnostic IndicatorsAudible/Buzzer/Alarm Feedback Power LED Green Master ARM only Learn Limit ModeGate Closes Then Opens Again on its Own Gate Opens Then Closes Again on its OwnGTO, Inc. Technical Service Department is open Repair ServiceGTO, Inc GateIf this Opener will be Used with Gates That are Mounted on Column Installation InformationMASONRY, BRICK, or Rock etc. Columns Read the Following Carefully Before ProceedingAccessories are Available From Your Retail Store AccessoriesAutomatic Gate Lock Pull-to-Open FM143

352 specifications

The GTO 352 is an innovative piece of engineering designed to meet the demands of modern users in various sectors, including transportation, logistics, and construction. This versatile machine stands out due to its robust design and advanced features that enhance productivity and efficiency on site.

One of the GTO 352’s main features is its powerful engine, which is designed to deliver outstanding performance while remaining fuel-efficient. The state-of-the-art powertrain not only ensures high torque but also reduces greenhouse gas emissions, making it an environmentally friendly choice for heavy-duty applications.

The GTO 352 is equipped with an advanced hydraulic system that allows for precise control when lifting and moving heavy loads. This system is complemented by its user-friendly interface, giving operators the ability to easily adjust settings and parameters for optimum performance. The machine's hydraulic capabilities can accommodate a variety of attachments, enhancing versatility and making it suitable for multiple tasks, from lifting to material handling.

In terms of design, the GTO 352 prioritizes operator comfort and safety. Its spacious cabin features ergonomically designed seating and intuitive controls, reducing fatigue during long working hours. Additionally, the machine is equipped with various safety features, including stability monitoring and automatic shut-off systems that ensure the well-being of the operator and surrounding personnel.

Another significant characteristic of the GTO 352 is its adaptability to various terrains. With a robust chassis and durable tires, it can handle rough and uneven surfaces, making it suitable for construction sites, warehouses, and rural areas alike. The machine’s all-wheel drive system improves traction and maneuverability, allowing for efficient operation in challenging conditions.

Technologically, the GTO 352 incorporates advanced sensors and software that allow for real-time monitoring of performance metrics. This data-driven approach enables users to make informed decisions regarding maintenance and operation, thereby extending the machine's life cycle and enhancing its operational efficiency.

Overall, the GTO 352 stands as a hallmark of innovation in its class. Its powerful performance, versatility, user-friendly design, and commitment to safety and efficiency make it an essential tool for professionals across various industries. As the world continues to move toward more sustainable and efficient practices, the GTO 352 promises to play a crucial role in meeting those demands.
Top Page Image Contents