GTO 352 installation manual Trench and Lay Conduit for Wiring, Preparing to Connect the Wires

Page 23

Trench and Lay Conduit for Wiring

Step 1

Trench and place 3/4 inch or larger PVC conduit from Master Opener Arm to Second Opener Arm. At this time you may also choose to trench and lay conduit from an AC power source to the gate for connecting the 18V transformer.

NOTE: If using solar power, trenching for the transformer is not necessary

Step 2

Route the 32 foot second battery harness cable and 32 foot Communication Cable through the PVC conduit running from the Second Opener Arm to the Master Opener Arm.

Second Opener

Master Opener

 

 

 

 

Trench cut across driveway for

3/4 inch or larger

routing of the Communication Cable

PVC Conduit

and Second Battery Harness Cable.

32 foot Second Battery Harness Cable and 32 foot Communication Cable routed through the PVC conduit.

IMPORTANT: After trenching driveway follow these guidelines for PVC installation and running wire.

•DON'T use too many curves in PVC. Use sweeping 90° angles. Wire should be easily removeable if needed.

•DON'T splice wire. This can cause a voltage drop and can interfere with sequencing and the rev counter.

•DON'T run wire in same conduit as AC wiring. This causes communication interference and electrical noise.

•DO use minimum of 3/4" ID (interior diameter) PVC conduit available at your local home improvement store.

Preparing to Connect the Wires

In order to have easy access to the control boards during the rest of the installation, remove the master and second openers and remount them upside down.

ON/OFF

Switch

Bottom

Access Panel

IMPORTANT:

Return opener arms to the upright position when installation is complete to prevent water damage to the control board.

ON

O FF

M i g h t y M u l e 3 5 2

19

Page 22 Page 24
Image 23
Page 22 Page 24
Contents 352 Place of Purchase Conversion ChartWhen You Know Multiply By To Find Table of Contents Please Read this First Disconnecting the Opener Important Safety InstructionsZone Entrapment Zones for aPull-To-Open Application Path of a Moving GateMoving Gate Area Driveway II. During InstallationAny control device within gray area III. After Installation Secondary Means of Protection Against Entrapment Entrapment Protection Required Safety Precautions for GatesInstall Warning Signs 352 Hardware Bag Contents Parts List Opener and Mounting HardwareTools Needed Operational Capacity PowerDrive ControlStep Installation OverviewPreparation of the Gate Pull-to-Open Gates Gate Opens into the PropertyRecommended Reinforcement Examples Installation of Mounting HardwareOpen Installation beginning on Post Bracket AssemblyBe sure gate opener and bracket dont bind GateGate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate Bracket StepMounting the Second Opener Installation of the Closed Position StopsMounting the Master Opener Illustration B Second Gate Opener Check ListPreparing to Connect the Wires Trench and Lay Conduit for WiringCable Communication Second ConduitON/OFF Solar Panel and Gate Activity Chart Powering Options Transformer or SolarConnecting The Battery Important Information about LOW Voltage Wire Connecting the TransformerMaster Arm Make sure the exposed wires do not touch each otherPull Push MODE1 MODE2 LOCK/BEACON Connecting Solar PanelsMaster Control Board Settings DIP Switches Main DIP Switch Settings ModesClose T IM E Stall Force Potentiometer SettingSetting Auto-Close Time Control BoardRun the cable through PVC conduit to protect it from damage Installing the ReceiverTesting Your Closed Limit Setting Setting the Closed Position LimitYour Mighty Mule 352 has two Limit Settings Closed Limit settingLearn Remote Button Setting Your Personal Transmitter CodeConnecting Additional Safety Devices Solar Panel + Control Board ConnectionsSolar Panel 18 VACGTO Automatic Lock Connecting AccessoriesSecond Opener Routing Wires Through The Access PanelMaster Opener Final Step When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationPress the SET Limit on the Master ARM for 5 Seconds Setting the Open Position LimitClearing Programmed Open Limit Setting Testing Your Open Limit SettingVisual/LEDs Feedback Visual and Audible Diagnostic IndicatorsAudible/Buzzer/Alarm Feedback Gate Opens Then Closes Again on its Own Learn Limit ModePower LED Green Master ARM only Gate Closes Then Opens Again on its OwnGate Repair ServiceGTO, Inc. Technical Service Department is open GTO, IncRead the Following Carefully Before Proceeding Column Installation InformationIf this Opener will be Used with Gates That are Mounted on MASONRY, BRICK, or Rock etc. ColumnsAccessories are Available From Your Retail Store AccessoriesAutomatic Gate Lock Pull-to-Open FM143

352 specifications

The GTO 352 is an innovative piece of engineering designed to meet the demands of modern users in various sectors, including transportation, logistics, and construction. This versatile machine stands out due to its robust design and advanced features that enhance productivity and efficiency on site.

One of the GTO 352’s main features is its powerful engine, which is designed to deliver outstanding performance while remaining fuel-efficient. The state-of-the-art powertrain not only ensures high torque but also reduces greenhouse gas emissions, making it an environmentally friendly choice for heavy-duty applications.

The GTO 352 is equipped with an advanced hydraulic system that allows for precise control when lifting and moving heavy loads. This system is complemented by its user-friendly interface, giving operators the ability to easily adjust settings and parameters for optimum performance. The machine's hydraulic capabilities can accommodate a variety of attachments, enhancing versatility and making it suitable for multiple tasks, from lifting to material handling.

In terms of design, the GTO 352 prioritizes operator comfort and safety. Its spacious cabin features ergonomically designed seating and intuitive controls, reducing fatigue during long working hours. Additionally, the machine is equipped with various safety features, including stability monitoring and automatic shut-off systems that ensure the well-being of the operator and surrounding personnel.

Another significant characteristic of the GTO 352 is its adaptability to various terrains. With a robust chassis and durable tires, it can handle rough and uneven surfaces, making it suitable for construction sites, warehouses, and rural areas alike. The machine’s all-wheel drive system improves traction and maneuverability, allowing for efficient operation in challenging conditions.

Technologically, the GTO 352 incorporates advanced sensors and software that allow for real-time monitoring of performance metrics. This data-driven approach enables users to make informed decisions regarding maintenance and operation, thereby extending the machine's life cycle and enhancing its operational efficiency.

Overall, the GTO 352 stands as a hallmark of innovation in its class. Its powerful performance, versatility, user-friendly design, and commitment to safety and efficiency make it an essential tool for professionals across various industries. As the world continues to move toward more sustainable and efficient practices, the GTO 352 promises to play a crucial role in meeting those demands.
Top Page Image Contents