GTO 352 installation manual Please Read this First

Page 4

®

E-Z GATE OPENERS

PLEASE READ THIS FIRST!

Thank you for purchasing a Mighty Mule® 352 E-Z Gate Opener—GTO's "do-it-yourself" automatic gate opener! When correctly installed and properly used, your Mighty Mule® 352 E-Z Gate Opener will give you many years of reliable service. Please read the following information and watch the enclosed video to ensure you have the correct system for your particular needs. Furthermore, this manual and the video will enable you to properly install your Mighty Mule® 352 E-Z Gate Opener.

The Mighty Mule® 352 E-Z Gate Opener is designed for installation on a pull-to-open dual gate leafs (gates that open into the property). By purchasing an accessory bracket (FM148), the Mighty Mule®

352 E-Z Gate Opener can accommodate a push-to-open dual gate leafs (gates that open out from the property). The gates must not exceed 8 feet and 550 pounds or exceed 16 feet and 150 pounds (please see Technical Specifications on page 10). The Mighty Mule® 352 EZ Gate Opener can be used on vinyl, aluminum, chain link, farm tube, and wrought iron gates.

Use on solid (surface) gates is not recommended. Solid surface gates have a high resistance to the wind. If the wind is strong enough, the opener will obstruct and stop, blow fuses, or may damage the equipment.

The Mighty Mule® 352 E-Z Gate Opener accommodates extra transmitters, digital keypads, solar panels, push buttons, automatic gate locks, and other access control products. These optional accessories (see the enclosed Mighty Mule® Accessory Catalog) are available at most stores. Your store should be able to special order any accessory not in stock. If your store cannot special order accessories, please call the GTO Sales Department (800-543-GATE).

The Mighty Mule® 352 E-Z Gate Opener features adjustable obstruction sensing. This safety feature makes the gate stop and reverse direction within 2 seconds when it comes in contact with an obstruction. MIN is the factory setting; meaning the gate will exert the minimum force on an obstruction before it stops and reverses direction.

The Mighty Mule® 352 E-Z Gate Opener also has an adjustable auto-close feature. After the gate reaches the fully open position, it can be set to remain open up to 120 seconds before automatically closing. Pressing the transmitter button at any time after the gate opens fully will cause it to close immediately. OFF is the factory setting; meaning the gate will stay open until you press the transmitter (or keypad, etc.) again.

PLEASE NOTE—If your application requires any of the following:

Slide gates;

Heavy duty or commercial uses;

Professional installation;

please call GTO at (800) 543-GATE [4283] or (850) 575-0176for information about our GTO/PRO professional line of gate openers and accessories. Our Sales Department will be glad to give you the name and phone number of a GTO/PRO dealer near you.

BEFORE YOU BEGIN TO INSTALL YOUR AUTOMATIC GATE OPENER:

watch the enclosed video and read these instructions carefully and completely to become familiar with all parts and installation steps. The video is only designed as an overview of the installation procedure. You must read the installation manual for detailed instructions on gate opener safety and proper use of the gate opener.

iii

Page 3 Page 5
Image 4
Page 3 Page 5
Contents 352 When You Know Multiply By To Find Conversion ChartPlace of Purchase Table of Contents Please Read this First Important Safety Instructions Disconnecting the OpenerEntrapment Zones for a Pull-To-Open ApplicationPath of a Moving Gate ZoneAny control device within gray area II. During InstallationMoving Gate Area Driveway III. After Installation Secondary Means of Protection Against Entrapment Install Warning Signs Required Safety Precautions for GatesEntrapment Protection 352 Parts List Opener and Mounting Hardware Hardware Bag ContentsTools Needed Power DriveControl Operational CapacityInstallation Overview Preparation of the GatePull-to-Open Gates Gate Opens into the Property StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Open Installation beginning onGate Be sure gate opener and bracket dont bindInstalling the Post Bracket Assembly and Gate Bracket Step Gate Bracket Mounting ExamplesMounting the Master Opener Installation of the Closed Position StopsMounting the Second Opener Illustration B Check List Second Gate OpenerTrench and Lay Conduit for Wiring Preparing to Connect the WiresCommunication Second Conduit CableON/OFF Powering Options Transformer or Solar Solar Panel and Gate Activity ChartConnecting The Battery Connecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Master ArmConnecting Solar Panels Master Control Board Settings DIP SwitchesMain DIP Switch Settings Modes Pull Push MODE1 MODE2 LOCK/BEACONStall Force Potentiometer Setting Setting Auto-Close TimeControl Board Close T IM EInstalling the Receiver Run the cable through PVC conduit to protect it from damageSetting the Closed Position Limit Your Mighty Mule 352 has two Limit SettingsClosed Limit setting Testing Your Closed Limit SettingSetting Your Personal Transmitter Code Learn Remote ButtonConnecting Additional Safety Devices Control Board Connections Solar Panel18 VAC Solar Panel +Connecting Accessories GTO Automatic LockMaster Opener Routing Wires Through The Access PanelSecond Opener When everything has been connected to the opener Final StepPush to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit Press the SET Limit on the Master ARM for 5 SecondsTesting Your Open Limit Setting Clearing Programmed Open Limit SettingAudible/Buzzer/Alarm Feedback Visual and Audible Diagnostic IndicatorsVisual/LEDs Feedback Learn Limit Mode Power LED Green Master ARM onlyGate Closes Then Opens Again on its Own Gate Opens Then Closes Again on its OwnRepair Service GTO, Inc. Technical Service Department is openGTO, Inc GateColumn Installation Information If this Opener will be Used with Gates That are Mounted onMASONRY, BRICK, or Rock etc. Columns Read the Following Carefully Before ProceedingAccessories Accessories are Available From Your Retail StoreAutomatic Gate Lock Pull-to-Open FM143

352 specifications

The GTO 352 is an innovative piece of engineering designed to meet the demands of modern users in various sectors, including transportation, logistics, and construction. This versatile machine stands out due to its robust design and advanced features that enhance productivity and efficiency on site.

One of the GTO 352’s main features is its powerful engine, which is designed to deliver outstanding performance while remaining fuel-efficient. The state-of-the-art powertrain not only ensures high torque but also reduces greenhouse gas emissions, making it an environmentally friendly choice for heavy-duty applications.

The GTO 352 is equipped with an advanced hydraulic system that allows for precise control when lifting and moving heavy loads. This system is complemented by its user-friendly interface, giving operators the ability to easily adjust settings and parameters for optimum performance. The machine's hydraulic capabilities can accommodate a variety of attachments, enhancing versatility and making it suitable for multiple tasks, from lifting to material handling.

In terms of design, the GTO 352 prioritizes operator comfort and safety. Its spacious cabin features ergonomically designed seating and intuitive controls, reducing fatigue during long working hours. Additionally, the machine is equipped with various safety features, including stability monitoring and automatic shut-off systems that ensure the well-being of the operator and surrounding personnel.

Another significant characteristic of the GTO 352 is its adaptability to various terrains. With a robust chassis and durable tires, it can handle rough and uneven surfaces, making it suitable for construction sites, warehouses, and rural areas alike. The machine’s all-wheel drive system improves traction and maneuverability, allowing for efficient operation in challenging conditions.

Technologically, the GTO 352 incorporates advanced sensors and software that allow for real-time monitoring of performance metrics. This data-driven approach enables users to make informed decisions regarding maintenance and operation, thereby extending the machine's life cycle and enhancing its operational efficiency.

Overall, the GTO 352 stands as a hallmark of innovation in its class. Its powerful performance, versatility, user-friendly design, and commitment to safety and efficiency make it an essential tool for professionals across various industries. As the world continues to move toward more sustainable and efficient practices, the GTO 352 promises to play a crucial role in meeting those demands.
Top Page Image Contents