GTO 352 installation manual Illustration B

Page 21

Step 1

Attach the horizontal closed position stop plate to the MASTER gate leaf.

1Z]aSR>]aWbW]\Ab]^>ZObS[]c\bSR V]`Wh]\bOZZg]\[SbOZ^]abeWbVCP]Zba

Detach the gate operators from the gates and move the gates to their closed position (Illustration A). Using appropriate hardware for your type of gate (U-bolts for tube or chain link; screw or bolts for wood or metal - not supplied) attach the closed position stop plate (horizontally) about mid height on

the MASTER gate frame. Do not tighten it completely at this time. Slide the stop plate toward the frame of the SECOND gate leaf until they touch (Illustration B). Once you have

4@=<BD73E

;/AB3@5ObS4`O[S

A31=<25ObS4`O[S

moved the stop plate to the correct position, tighten its hardware completely.

Illustration B

B=>D73E

NOTE: The optional ground stop post is used to provide a secure point for the SECOND gate to close against. If you will be using the GTO Horizontal Gate Lock accessory with your gate opener system, the closed position ground stop is REQUIRED, as shown in Steps 2 and 3.

Closed Position Stop Plate mounted on the gate leaf that CLOSES FIRST

Step 2

Install a low profile ground stop (not provided) beneath the SECOND gate stop plate.

The ground stop needs to be positioned near the end of the gate as shown in Illustration A and may be made of metal or concrete and should be firmly secured in the ground (we recommend setting it in concrete).

VerticallyMount

FRONT VIEW

Illustration C

SIDE VIEW

Closed Position Stop Plate

Low Profile Ground Stop

in Near the Center of Driveway

Step 3

Attach a vertical closed position stop plate to the SECOND gate.

Using appropriate hardware for your type of gate attach the vertical closed position stop plate to the SECOND gate frame at the point where it will come in contact with the ground stop post. Do not tighten it completely at this time. You must slide the closed position stop plate toward the ground stop until they touch (Illustration C). Once you have moved the stop plate to the correct position, tighten its hardware completely.

NOTE: For a push-to-open installation (gates open out from the property) attach the closed position stop plate to the outside of the gate.

M i g h t y M u l e 3 5 2

17

Page 20 Page 22
Image 21
Page 20 Page 22
Contents 352 Conversion Chart When You Know Multiply By To FindPlace of Purchase Table of Contents Please Read this First Disconnecting the Opener Important Safety InstructionsPull-To-Open Application Entrapment Zones for aPath of a Moving Gate ZoneII. During Installation Any control device within gray areaMoving Gate Area Driveway III. After Installation Secondary Means of Protection Against Entrapment Required Safety Precautions for Gates Install Warning SignsEntrapment Protection 352 Hardware Bag Contents Parts List Opener and Mounting HardwareTools Needed Drive PowerControl Operational CapacityPreparation of the Gate Installation OverviewPull-to-Open Gates Gate Opens into the Property StepRecommended Reinforcement Examples Installation of Mounting HardwareOpen Installation beginning on Post Bracket AssemblyBe sure gate opener and bracket dont bind GateGate Bracket Mounting Examples Installing the Post Bracket Assembly and Gate Bracket StepInstallation of the Closed Position Stops Mounting the Master OpenerMounting the Second Opener Illustration B Second Gate Opener Check ListPreparing to Connect the Wires Trench and Lay Conduit for WiringCable Communication Second ConduitON/OFF Solar Panel and Gate Activity Chart Powering Options Transformer or SolarConnecting The Battery Important Information about LOW Voltage Wire Connecting the TransformerMaster Arm Make sure the exposed wires do not touch each otherMaster Control Board Settings DIP Switches Connecting Solar PanelsMain DIP Switch Settings Modes Pull Push MODE1 MODE2 LOCK/BEACONSetting Auto-Close Time Stall Force Potentiometer SettingControl Board Close T IM ERun the cable through PVC conduit to protect it from damage Installing the ReceiverYour Mighty Mule 352 has two Limit Settings Setting the Closed Position LimitClosed Limit setting Testing Your Closed Limit SettingLearn Remote Button Setting Your Personal Transmitter CodeConnecting Additional Safety Devices Solar Panel Control Board Connections18 VAC Solar Panel +GTO Automatic Lock Connecting AccessoriesRouting Wires Through The Access Panel Master OpenerSecond Opener Final Step When everything has been connected to the openerSwinging gates shall not open into public access areas Push to Open InstallationPress the SET Limit on the Master ARM for 5 Seconds Setting the Open Position LimitClearing Programmed Open Limit Setting Testing Your Open Limit SettingVisual and Audible Diagnostic Indicators Audible/Buzzer/Alarm FeedbackVisual/LEDs Feedback Power LED Green Master ARM only Learn Limit ModeGate Closes Then Opens Again on its Own Gate Opens Then Closes Again on its OwnGTO, Inc. Technical Service Department is open Repair ServiceGTO, Inc GateIf this Opener will be Used with Gates That are Mounted on Column Installation InformationMASONRY, BRICK, or Rock etc. Columns Read the Following Carefully Before ProceedingAccessories are Available From Your Retail Store AccessoriesAutomatic Gate Lock Pull-to-Open FM143

352 specifications

The GTO 352 is an innovative piece of engineering designed to meet the demands of modern users in various sectors, including transportation, logistics, and construction. This versatile machine stands out due to its robust design and advanced features that enhance productivity and efficiency on site.

One of the GTO 352’s main features is its powerful engine, which is designed to deliver outstanding performance while remaining fuel-efficient. The state-of-the-art powertrain not only ensures high torque but also reduces greenhouse gas emissions, making it an environmentally friendly choice for heavy-duty applications.

The GTO 352 is equipped with an advanced hydraulic system that allows for precise control when lifting and moving heavy loads. This system is complemented by its user-friendly interface, giving operators the ability to easily adjust settings and parameters for optimum performance. The machine's hydraulic capabilities can accommodate a variety of attachments, enhancing versatility and making it suitable for multiple tasks, from lifting to material handling.

In terms of design, the GTO 352 prioritizes operator comfort and safety. Its spacious cabin features ergonomically designed seating and intuitive controls, reducing fatigue during long working hours. Additionally, the machine is equipped with various safety features, including stability monitoring and automatic shut-off systems that ensure the well-being of the operator and surrounding personnel.

Another significant characteristic of the GTO 352 is its adaptability to various terrains. With a robust chassis and durable tires, it can handle rough and uneven surfaces, making it suitable for construction sites, warehouses, and rural areas alike. The machine’s all-wheel drive system improves traction and maneuverability, allowing for efficient operation in challenging conditions.

Technologically, the GTO 352 incorporates advanced sensors and software that allow for real-time monitoring of performance metrics. This data-driven approach enables users to make informed decisions regarding maintenance and operation, thereby extending the machine's life cycle and enhancing its operational efficiency.

Overall, the GTO 352 stands as a hallmark of innovation in its class. Its powerful performance, versatility, user-friendly design, and commitment to safety and efficiency make it an essential tool for professionals across various industries. As the world continues to move toward more sustainable and efficient practices, the GTO 352 promises to play a crucial role in meeting those demands.
Top Page Image Contents