GTO 352 Entrapment Zones for a, Pull-To-Open Application, Path of a Moving Gate

Page 6

IMPORTANT SAFETY INSTRUCTIONS

For The Consumer

WARNING: To reduce the risk of injury or death:

1.READ AND FOLLOW ALL INSTRUCTIONS. Failure to meet the requirements set forth in the instruction manual could cause severe injury and/or death, for which the manufacturer cannot be held responsible.

2.When designing a system that will be entered from a highway or main thoroughfare, make sure the system is placed far enough from the road to prevent traffic congestion.

3.The gate must be installed in a location that provides adequate clearance between it and adjacent structures when opening and closing to reduce the risk of entrapment. Swinging gates must not open into public access areas.

4.The gate and gate opener installation must comply with any applicable local codes.

I. Before Installation

1.Verify this opener is proper for the type and size of gate, its frequency of use and the proper class rating.

2.Make sure the gate has been properly installed and swings freely in both directions. Repair or replace all worn or damaged gate hardware prior to installation. A freely moving gate will require less force to operate and will enhance the performance of the opener and safety devices used with the system.

3.Review the operation of the system to become familiar with its safety features. Understand how to disconnect the opener for manual gate operation (see page 1).

4.This gate opener is intended for vehicular gates ONLY. A separate entrance or gate must be installed for pedestrian use (see page 6).

5.Always keep people and objects away from the gate and its area of travel. NO ONE SHOULD CROSS

THE PATH OF A MOVING GATE.

6.Pay close attention to the diagram below and be aware of these areas at all times.

 

ZONE 1

 

ZONE 2

 

ZONE 2

ZONE 5

 

ZONE 5

ZONE 3

 

ZONE 3

ZONE 4

Driveway

ZONE 4

Gate in the

Entrapment Zones for a

Gate in the

Open Position

Pull-To-Open Application

Open Position

 

 

2

M i g h t y M u l e 3 5 2

 

Page 5 Page 7
Image 6
Page 5 Page 7
Contents 352 Conversion Chart When You Know Multiply By To FindPlace of Purchase Table of Contents Please Read this First Important Safety Instructions Disconnecting the OpenerPath of a Moving Gate Entrapment Zones for aPull-To-Open Application ZoneII. During Installation Any control device within gray areaMoving Gate Area Driveway III. After Installation Secondary Means of Protection Against Entrapment Required Safety Precautions for Gates Install Warning SignsEntrapment Protection 352 Parts List Opener and Mounting Hardware Hardware Bag ContentsTools Needed Control PowerDrive Operational CapacityPull-to-Open Gates Gate Opens into the Property Installation OverviewPreparation of the Gate StepInstallation of Mounting Hardware Recommended Reinforcement ExamplesPost Bracket Assembly Open Installation beginning onGate Be sure gate opener and bracket dont bindInstalling the Post Bracket Assembly and Gate Bracket Step Gate Bracket Mounting ExamplesInstallation of the Closed Position Stops Mounting the Master OpenerMounting the Second Opener Illustration B Check List Second Gate OpenerTrench and Lay Conduit for Wiring Preparing to Connect the WiresCommunication Second Conduit CableON/OFF Powering Options Transformer or Solar Solar Panel and Gate Activity ChartConnecting The Battery Connecting the Transformer Important Information about LOW Voltage WireMake sure the exposed wires do not touch each other Master ArmMain DIP Switch Settings Modes Connecting Solar PanelsMaster Control Board Settings DIP Switches Pull Push MODE1 MODE2 LOCK/BEACONControl Board Stall Force Potentiometer SettingSetting Auto-Close Time Close T IM EInstalling the Receiver Run the cable through PVC conduit to protect it from damageClosed Limit setting Setting the Closed Position LimitYour Mighty Mule 352 has two Limit Settings Testing Your Closed Limit SettingSetting Your Personal Transmitter Code Learn Remote ButtonConnecting Additional Safety Devices 18 VAC Control Board ConnectionsSolar Panel Solar Panel +Connecting Accessories GTO Automatic LockRouting Wires Through The Access Panel Master OpenerSecond Opener When everything has been connected to the opener Final StepPush to Open Installation Swinging gates shall not open into public access areasSetting the Open Position Limit Press the SET Limit on the Master ARM for 5 SecondsTesting Your Open Limit Setting Clearing Programmed Open Limit SettingVisual and Audible Diagnostic Indicators Audible/Buzzer/Alarm FeedbackVisual/LEDs Feedback Gate Closes Then Opens Again on its Own Learn Limit ModePower LED Green Master ARM only Gate Opens Then Closes Again on its OwnGTO, Inc Repair ServiceGTO, Inc. Technical Service Department is open GateMASONRY, BRICK, or Rock etc. Columns Column Installation InformationIf this Opener will be Used with Gates That are Mounted on Read the Following Carefully Before ProceedingAccessories Accessories are Available From Your Retail StoreAutomatic Gate Lock Pull-to-Open FM143

352 specifications

The GTO 352 is an innovative piece of engineering designed to meet the demands of modern users in various sectors, including transportation, logistics, and construction. This versatile machine stands out due to its robust design and advanced features that enhance productivity and efficiency on site.

One of the GTO 352’s main features is its powerful engine, which is designed to deliver outstanding performance while remaining fuel-efficient. The state-of-the-art powertrain not only ensures high torque but also reduces greenhouse gas emissions, making it an environmentally friendly choice for heavy-duty applications.

The GTO 352 is equipped with an advanced hydraulic system that allows for precise control when lifting and moving heavy loads. This system is complemented by its user-friendly interface, giving operators the ability to easily adjust settings and parameters for optimum performance. The machine's hydraulic capabilities can accommodate a variety of attachments, enhancing versatility and making it suitable for multiple tasks, from lifting to material handling.

In terms of design, the GTO 352 prioritizes operator comfort and safety. Its spacious cabin features ergonomically designed seating and intuitive controls, reducing fatigue during long working hours. Additionally, the machine is equipped with various safety features, including stability monitoring and automatic shut-off systems that ensure the well-being of the operator and surrounding personnel.

Another significant characteristic of the GTO 352 is its adaptability to various terrains. With a robust chassis and durable tires, it can handle rough and uneven surfaces, making it suitable for construction sites, warehouses, and rural areas alike. The machine’s all-wheel drive system improves traction and maneuverability, allowing for efficient operation in challenging conditions.

Technologically, the GTO 352 incorporates advanced sensors and software that allow for real-time monitoring of performance metrics. This data-driven approach enables users to make informed decisions regarding maintenance and operation, thereby extending the machine's life cycle and enhancing its operational efficiency.

Overall, the GTO 352 stands as a hallmark of innovation in its class. Its powerful performance, versatility, user-friendly design, and commitment to safety and efficiency make it an essential tool for professionals across various industries. As the world continues to move toward more sustainable and efficient practices, the GTO 352 promises to play a crucial role in meeting those demands.
Top Page Image Contents