Genie 3064H manual Adjustment Guide Force Settings, Change Force Setting, Blue Purple

Page 23

ADJUSTMENT GUIDE - FORCE SETTINGS

CAUTION

Door closing force is FACTORY set and requires no adjustment for normal operation.

Never increase the door closing force to compensate for a damaged door or a binding door track.

Never adjust force to compensate for a broken door spring.

Perform monthly CONTACT REVERSE TEST as described on page 18.

Force settings are pre-programmed at the factory and "learned" during the Open/Close Limit settings steps. Some additional Force may be increased. For normal use, Force settings should not need adjustment with this unit.

However, conditions that might suggest an adjustment is necessary are;

Doors with very stiff weather seals.

Doors that start down, then STOP and reverse before they close.

Doors that start up, but STOP before they completely open.

FOR HELP-1-800-35-GENIE OR WWW.GENIECOMPANY.COM

CHANGE FORCE SETTING

Use this guide to ADJUST powerhead FORCE settings. NOTE: There are nine (9) force levels.

PROGRAM

1.Press on the powerhead and hold until both

SET

lights turn steady ON. Release button.

Lights go out and Round BLUE light comes ON.

2.Press three times, Round RED light comes ON.

PROGRAM

3.Press once to enter the Force Programming menu.SET The round LED will flash BLUE 3 times, then the current Force setting for UP force will display on the LEDs. See table below.

4.(If current UP Force setting is good, skip to Step

5.) Press to increase or to decrease UP Force

settings within the available range.

PROGRAM

5.Press SET to set UP Force level. The long LED will flash BLUE 3 times, then the current Force setting for DOWN force will display on the LEDs.

6.(If current DOWN Force setting is good, skip to Step 7.) Press to increase or to decrease

DOWN Force settings within the available range.

PROGRAM

7.Press SET to set DOWN Force level. Both LEDs flash BLUE to confirm.

Force Level

Powerhead LEDs

Round LED Long LED

Default LED display is the current Force setting

LED indicator colors

OFF,

Blue,

Purple,

Red

Force Level LED indicator colors

Force Level 1

Force Level 2

Force Level 3

Force Level 4

Force Level 5

Force Level 6

Force Level 7

Force Level 8

Force Level 9

Blue

OFF

ON

 

OFF

Blue

ON

 

Blue

Blue

ON

ON

Purple

OFF

ON

 

OFF

Purple

ON

 

Purple

Purple

ON

ON

Red

OFF

ON

 

OFF

Red

ON

 

Red

Red

ON

ON

©2010 The Genie Company

12/2010

23

Image 23
Contents Operation and Maintenance Manual Prevention Potential HazardSafety Features Opener FeaturesTable of Contents Infrared Protection Function Important Installation InstructionsProgramming Limits & Force Both LEDs flash Blue Go OFF PressSee long Blue LED flashing Press and Hold until door is Fully Open then ReleaseTest AdjustmentSee both LEDs Flash Blue See both LEDs OFF Program Intellicode 2 Remote to PowerheadIntelliCode 1 remotes See round Blue LED come onSee long Purple LED flashing Genie IntelliCode 1 wireless keypadGenie IntelliCode 1 remote See oneReference Powerhead & Rail Assembled View Typical Sectional Door Installation Typical ONE Piece Door Installation Programming Buttons location Overview of Powerhead ControlsOn powerhead Simultaneously on Overview Remotes and OptionsHold Press both2010 IntelliCode Intellicode FeaturesUse this New IntelliCode 2 openersTransmitter Compliance Statement Maintenance & TroubleshootingDoor Balance Spring Tension Routine Monthly MaintenanceAdjustment Safe-T-Beam System Check Door balance Contact reverseShuttle ENGAGE/DISENGAGE Disconnect power to door openerReset OPEN/CLOSE Travel Limit Change Light BulbsControls door opener lights from inside garage Wire routingWall Console Overview Open and closes door from inside garageThis area left blank Remote Battery ReplacementPowerhead LEDs Round LED Long LED Adjustment Guide Speed SettingsChange Speed Setting Force Level LED indicator colors Adjustment Guide Force SettingsChange Force Setting Down Force settings within the available rangeTroubleshooting Guide Operation Powerhead LED Possible Problem Solution Opening Cover May Cause Electric Shock Disconnect power from opener prior to removing coverTrilo

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.