Genie 3064H manual Important Installation Instructions, Infrared Protection Function

Page 5

Begin here after the opener's physical assembly

and installation has been completed.

There are no assembly or installation steps included in this manual. Contact your Genie® Professional Dealer for an installation poster, if required, or visit www.geniecompany.com to download a PDF file.

The following mechanical assembly tasks must be completed before continuing.

Powerhead and rail are bolted to each other (An illustration is shown on page 11) Example illustrations of the following items are shown on pages 12 and 13

Rail end is attached to a header bracket which is attached to the garage door header

Powerhead is attached to a support frame suspended from the ceiling or ceiling joists

Both pieces of door arms are assembled and are attached to the garage door

Safe-T-Beam® sensors installed and wired

Wall console installed and wired (Shown on page 20)

Shuttle is engaged to Screw Drive Carriage (An illustration is shown on page 11)

Powerhead is plugged into an approved power outlet

Begin programming by setting Limits (see next page.)

A PDF VERSION INSTALLATION POSTER IS AVAILABLE AT WWW.GENIECOMPANY.COM

OR CALL 1-800-35-GENIE TO OBTAIN AN EMAIL PDF FILE

IMPORTANT INSTALLATION INSTRUCTIONS

WARNING:Toreducetheriskofsevereinjuryordeath:

1.READ AND FOLLOW ALL SAFETY, INSTALLATION AND OPERATION INSTRUCTIONS. (If you have questions or do not understand an instruction, call The Genie Company.)

2.Install only on a properly balanced sectional or one piece garage door. An improperly balanced door could cause severe injury. Have a trained door system technician make repairs or adjustments to cables, spring assemblies, and other hardware before installing the opener.

3.Remove all ropes and remove or make inoperative all locks connected to the garage door before installing opener.

4.Where possible, install the door opener 7 feet or more above the floor. For products having an emergency release, mount the emergency release 6 feet above the floor.

5.Do NOT connect the opener to source of power until instructed to do so.

6.Locate the wall console:

•Within sight of the garage door,

•At minimum height of 5 feet so small children are not able to reach it, and

•Away from all moving parts of the door.

7.Install the Entrapment WARNING Label next to the wall console in a prominent location.

8.After installing the opener, the door must reverse within 2 seconds when it contacts a 1-1/2 inch high object (or a 2 x 4 board laid flat) on the floor.

INFRARED PROTECTION FUNCTION

1.When garage door is opening, its movement will not be influenced if the Safe-T-Beam® is obstructed.

2.If the Safe-T-Beam® is obstructed before the garage door fully closes, the door will not close.

3.When the garage door is closing, if Safe-T-Beam® is interrupted by person or obstacle, the garage door will stop its downward travel and reverse automatically to its fully opened position.

4.Remove Safe-T-Beam® obstruction.

5.If the Safe-T-Beam® System fails, loses power, or is installed improperly, press and hold the wall console "open/close" button until the door reaches its fully closed position. If you release the "open/close" button on the wall console during the closing movement the door will reverse automatically to its fully opened position.

©2010 The Genie Company

12/2010

5

Page 4 Page 6
Image 5
Page 4 Page 6
Contents Operation and Maintenance Manual Prevention Potential HazardSafety Features Opener FeaturesTable of Contents Infrared Protection Function Important Installation InstructionsProgramming Limits & Force See long Blue LED flashing PressPress and Hold until door is Fully Open then Release Both LEDs flash Blue Go OFFTest AdjustmentIntelliCode 1 remotes Program Intellicode 2 Remote to PowerheadSee round Blue LED come on See both LEDs Flash Blue See both LEDs OFFGenie IntelliCode 1 remote Genie IntelliCode 1 wireless keypadSee one See long Purple LED flashingReference Powerhead & Rail Assembled View Typical Sectional Door Installation Typical ONE Piece Door Installation Programming Buttons location Overview of Powerhead ControlsOn powerhead Hold Overview Remotes and OptionsPress both Simultaneously onUse this Intellicode FeaturesNew IntelliCode 2 openers 2010 IntelliCodeTransmitter Compliance Statement Maintenance & TroubleshootingAdjustment Routine Monthly MaintenanceSafe-T-Beam System Check Door balance Contact reverse Door Balance Spring TensionReset OPEN/CLOSE Travel Limit Disconnect power to door openerChange Light Bulbs Shuttle ENGAGE/DISENGAGEWall Console Overview Wire routingOpen and closes door from inside garage Controls door opener lights from inside garageThis area left blank Remote Battery ReplacementPowerhead LEDs Round LED Long LED Adjustment Guide Speed SettingsChange Speed Setting Change Force Setting Adjustment Guide Force SettingsDown Force settings within the available range Force Level LED indicator colorsTroubleshooting Guide Operation Powerhead LED Possible Problem Solution Opening Cover May Cause Electric Shock Disconnect power from opener prior to removing coverTrilo

3064H, 3064 specifications

The Genie 3064 and 3064H are renowned models in the realm of compact aerial work platforms. These versatile machines are designed for indoor and outdoor construction, maintenance, and industrial applications. Their compact design and advanced technologies make them suitable for tight spaces, while their impressive lift capabilities ensure productivity and safety.

One of the defining features of the Genie 3064 series is its impressive working height. The 3064 model can reach heights of up to 36 feet, enabling operators to perform tasks high above the ground safely and efficiently. The 3064H variant, with its hybrid technology, allows for seamless transitions between electric and diesel power, making it exceptionally versatile for various job sites. The hybrid engine ensures minimal emissions, which is particularly beneficial for indoor applications where air quality is a concern.

The Genie 3064 series boasts a maximum capacity of 500 pounds. This makes it ideal for tasks that require multiple workers, tools, and equipment. The platform's extension offers increased reach, allowing users to work on a wider area without the need to reposition the lift frequently. This feature enhances productivity and minimizes downtime, crucial factors in any construction or maintenance project.

Both models come equipped with Genie’s signature technology, the Smart Link Control System, which provides intuitive operation and helps reduce training time for new operators. The user-friendly interface integrates critical information, including platform height, load capacity, and battery levels, ensuring that operators have all necessary data at their fingertips.

The machines are built with durability in mind. High-grade steel and robust components ensure they can withstand the rigors of challenging job sites. The steel chassis provides stability while the non-marking tires protect floors in sensitive indoor environments.

Safety is a top priority with the Genie 3064/3064H series. Features like guardrails, emergency stop buttons, and a tilt sensor are standard, ensuring compliance with stringent safety regulations. The design allows for rapid deployment, reducing setup time and enhancing accessibility.

In summary, the Genie 3064 and 3064H aerial work platforms combine innovative technology, robust construction, and user-friendly features. Their versatility, safety measures, and exceptional performance make them a preferred choice for contractors, maintenance teams, and anyone needing reliable access solutions in various environments.
Top Page Image Contents